{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
Voltage: 12 V
Current: 170 mA
Frequency: 20 MHz - 7,000 MHz
The PAM-0207 is a preamplifier from A.H. Systems. The beneficial product has 20MHz-7000MHz frequency range, less-noise feature, individual calibration with gain calibration, and low VSWR. This apparatus has a hassle-free ...
Voltage: 15 V
Current: 275 mA
Frequency: 18 GHz - 40 GHz
The A.H. Systems' Preamplifier Line comes with high gain within rugged construction. The device features easy and simple soldering with its power leads. It also equipped with a 15-volt DC regulated power source. By using ...
Voltage: 275 mV
The OPLabBox is suitable for wide variety of ultrasonic applications, due to its wide bandwidth amplifier with switched bandpass filter and integrated pulser. Its bandwith ranges from 40 kHz up to 22 MHz. This product functions as a scope ...
Voltage: 9 V
Current: 80, 100 mA
PIP is the programmable smart preamplifier. Due to the modern internal configuration, it offers extreme flexibility combined with superior signal parameters and high reliability. Included voltage monitor allows user to ...
VIGO System
Voltage: 9, 15 V
Current: 50 mA
SIP is the ultra small transimpedance, AC or DC coupled preamplifier. It is dedicated for OEM applications and requires external heat sink (see Recommended Accessories). SIP is designed for operation with either biased ...
VIGO System
Voltage: 9, 15 V
Current: 50 mA
... or DC coupled preamplifier. It is dedicated for BenchTop applications. Package type F is equipped with fan and does not require additonal heat sink. Pacakage type NF requires additional heat dissipation (provided by user). MIP ...
VIGO System
Voltage: 28 V
... Microphone Preamplifier Type 1706 enables you to make acoustical measurements at temperatures up to 125°C (257°F) with a constant-current line drive (CCLD) input module. You can connect ½″ prepolarized microphones to ...
Bruel and Kjaer
Voltage: 1.7 V - 25 V
Under the range of analog and mixed signal solutions, we have our TI analog Microphone Preamplifier audio products. On this page you can obtain samples, notes for applications, data sheets, and generally search for a ...
Voltage: 10 V
Current: 100 mA
The SIM918 is a flexible preamplifier that features auto-zeroing that can be controlled remotely or from the front panel suitable for sensitive applications requiring minimal input offset voltage. Measured and nulled ...
Voltage: 2.4 V - 5.5 V
Current: 0.02 A - 3.1 A
... high-performance microphone amplifier. It contains an automatic gain control and low-noise microphone bias. The low-noise preamplifier features a 12dB gain while the VGA gain features an automatic adjustment in a range ...
Our In-Line series of preamplifiers are small (approximately 1” x 1” x 2.2”), low-cost devices that are well-suited for applications where there is a known, specific preamplifier requirement. They have ...
Physical Acoustics
What do you do when your favorite pH/ORP electrode isn't available with a built-in preamplifier, but you need to send the signal a few hundred feet? Hook up to this external preamp and you can go 1000 feet if necessary! ...
Voltage: 15 V - 25 V
Current: 0.5 mA - 5 mA
* Constant Current Operation Applicable Microphone MI-1233 / MI-1234 / MI-1431 / MI-1432 Frequency Bandwidth 10 Hz to 20 kHz Gain -2 dB ± 1 dB (At 1 kHz) Input Impedance Approximately 5 G Ohm Intrinsic Noise ...
Voltage: 12 V - 24 V
Current: 4 mA - 30 mA
The CANBERRA Model 2003BT charge sensitive FET input preamp is designed for optimum performance with Silicon Surface Barrier (SSB) detectors. Operating as a charge to voltage converter, the unit accepts charge carriers produced in the ...
Voltage: 10 V
Current: 50 mA
... between force sensor and control cabinet is often higher than the permissible length of cable. For these applications is the preamplifier PAM is especially suitable. The low level of the strain gauge sensor signals will ...
• Constant current powered measuring microphone preamplifier PA-01 with electret condenser microphone capsule type MP40. The current powered 1/2" Measuring Microphone offers facilities for the use of a high-quality noise ...
Constant current powered measuring microphone preamplifier for electret condenser microphone capsules with memory microphone identification The current powered 1/4 measuring microphone preamplifier MV ...
Microtech Gefell GmbH
Voltage: 14.8 V
Applications: Works with all Bangos acoustic emission sensors.
Tehnološki Koncepti d.o.o.
Voltage: 400 mV
The PA200-10 preamplifier module is engineered for utilization with Photek detectors with the help of numerous micro passage dishes as they generate a short instant electrical pulse for every photon and piece flowing ...
Voltage: 6 V
The A250 is a hybrid state-of-the-art Charge Sensitive Preamplifier for use with a wide range of detectors having capacitance from less than one, to several thousand picofarads. Such detectors include silicon, CdTe, CZT, ...
Microsemi's amplifiers and pre-amplifiers can be used in multiple applications that require high efficiency and low-noise. The product family includes operational amplifiers, Class-D Audio amplifiers and Microphone pre-amplifiers.
Voltage: 14 V
4048 Phantom Powered Measurement/Studio Microphone Preamp * 3 Pin Male SLR Industry StandardModel 4048 PreAmp Configuration * 18-48 Vdc Phantom * Low Noise <2 uV dBA @ 22pF Max Output 14 Vp-p (5 Vrms) * 1/2 Inch Microphone ...
ACO Pacific, Inc.
The G.R.A.S. ½-inch Preamplifi er Type 26CA is ageneral purpose preamplifi er optimized for use withprepolarized condenser microphones. It is a small,robust unit and uses a G.R.A.S. CCP power supply(ICP ®), e.g. Type 12AL. It has a very ...
G.R.A.S. Sound & Vibration
Preamplifier Overview A preamplifier with high input impedance and lew output impedance is required in order to faithfully transfer the voltage converted by the microphone to the subsequent amplifier. In ...
... cables available including flat tape types to pass under doors etc. It has an M3 thread hole in the preamplifier body, allowing easy mounting of the preamplifier for various measurement applications.
Norsonic AS
The single-channel preamplifi er is used for signal transmission between a dispensing valve with pressure sensor and a downstream Loctite controller 97152 or 97153. The amplifying factor is adjusted depending on the viscosity of the product ...