|
|
The Femto-LiteTM is an 11 mm wide hot runner nozzle ideal for small closures, flip-top caps, personal care and multi-material / multi-colour products.
Engineered for applications requiring inside gating and tight pitch designs, its 19 mm pitch and a flange to tip heat profile make it suitable for a wide variety of thermoplastic resins.
Features at a glance:
Standard lengths from 73 to 163 mm, with a 3.5 mm runner diameter and 12 mm well bore makes it suitable for close gate-to-gate spacing.
Available in five gating options for both tip and sprue gates.
|
|
| Precision-engineered and made in Switzerland, Herzog® brand machine nozzles can help you make better parts, and more of them... day in and day out. Xaloy is the sole authorized distributor of genuine Herzog® nozzles and spare parts throughout the Americas and Asia-Pacfic regions. |
|
hotslot® bases on the proved principle of hotspring® coil heaters (type WRP/Mini resp. WRP/Micro, other on request). Pressed into nearly any slot e. g. on a turning part or carrier plate, hotslot® grants an optimal power distribution.
A requested temperation according to the application-specific requirements can be realised by this principle.
The carrier material out off brass resp. stainless steel can be provided with special holes or cut outs as per desired specification.
A very special innovation is the hotslot® with its minimum wall thickness of 1 mm along the complete heating element (connection area included).
With a surface load of a maximum of 12.5 W/cm2 resp. 10 W/cm2 and flexible connection voltage hotslot® precisely heat: Reliable, process-sure and absolutely space-saving! |
|
| ... products without technical information |
| |
URR
The URR water nozzle produces a pressurized water spray which canbe continuously adjusted from a powerful straight jet, to a 160° round water curtain with a 11 meter (36 feet) diameter.
Please note the capacity changes in these two extreme operating conditions.
A strong rubber ring circles the diameter immediately behind the orifice, to avoid damages due to shocks.
URS
These lances make it possible to insantly switch among three different conditions, that is closed %u2013 straight jet %u2013 adjustable full cone spray.
The two larger size models can be supplied complete with an optional water curtain, to avoid the fire fighter beoing exposed to radiant heat from the open flame. |
|
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
... see all the products in the category
Hoses
|
Bulk materials are frequently stored in hoppers and silos. To do different
environemental conditions and divers product caracteristics the discharge
and empting of such hoppers and silos can cause troubles.
On the market different discharge pads are offered. Gericke uses, beside of
its RA Bin Discharger and vibrating Bin Dischargers, aeration nozzles (flow
pad). This nozzles inject the 10 Nm3 air per hour and per nozzle in to the
hopper. By this measure the airflow fluidises the product and cleanes the
inside of the compartment.
The installation of the flow pad is very easy and simple just drill a hole
with diameter 53mm and fix the flow pad with 4 screws.
|
|
| Low-maintenance spray marking system produces neat circles and stripes between from .2%u201D to 1.2%u201D wide. A programmable air delay after each cycle prevents clogging, which greatly reduces maintenance and downtime. |
|
The ThermJet is a nozzle-mix burner designed to fire an intense stream of hot gases through a combustor using combustion air temps up to 600° F. (315° C.)
The high velocity of the gases improves temperature uniformity, product quality and system efficiency.
The TJ burner comes in two types: High Velocity (HV) and Medium Velocity (MV)
The gas velocity can be as high as 500 ft/s (150 m/s) for the HV, and 250 ft/s (75 m/s)for the MV.
|
|
| The MAXON VALUPAK® gas burner provides a convenient, packaged solution for direct fired heating applications in ovens and dryers. The burner fires cleanly into applications with balanced pressure where high turndown of over 40:1 is required for precise temperature control. Durable steel construction provides years of reliable service. VALUPAK® is available in wide variety of packaged forms to suit your application for a bolt-on solution. |
|
Selas nozzle mix burners offer many advantages over typical flame-type burners. They are designed to thoroughly mix combustion air and fuel gas at the nozzle so that it can burn quickly and completely. Combustion occurs within the nozzle, so the heat exiting from the nozzle cup is uniform, stable and highly controlled. This rapid combustion creates a quick release heat, radiated from fully reacted gases that are closer to a theoretical flame temperature, but with no danger of flame impingement on the workpiece.
Selas nozzle mix burners are ideal for smaller furnaces. Since there is no chance of flame impingement, the distance from the burner to the workpiece is shorter. You'll also save money on fuel costs with Selas nozzle mix burners because they require less air to fuel combustion. |
|
| MAXON APX® Natural Gas Burners are packaged nozzle mixing line burners designed for fresh or low temperature re-circulated air heating applications. The APX® Industrial Burner is a value engineered design utilizing a single aluminum extrusion for both its air and fuel manifolds. Its single-piece, joint-less body design provides standard straight gas burners up to 40 feet, H-shaped burners, and grid shaped burners engineered to your specification. APX® burner construction provides years of maintenance free operation and lower cost of ownership than any other alternative. |
|
| ... products without technical information |
| |
45° spiral flute :
This type of taper reamer is indispensable to moulders for making injection nozzles in rational fashion.
flute number :2 up to Ø14mm - 3 over.
Straight flute :
The straight flute taper reamers with chipbreaker are recommended when faultless conical holes are desired. It is then possible to avoid any special copyin phenomenon.
flute ni=umber : 3 up to Ø4 - 5 over.
Material : HSS-E Cobalt
Diameters : Ø2.0mm to Ø30.0mm
page 102 from Magafor 701 |
|
Nozzle Oscillation Type Brushless Inslot Winding Machine
CIT-0150-S / CIT-0150-M / CIT-0150-L
High productivity, due to 3-nozzle synchronized winding for 3-phase motor.
Numerically controled, synchronized 3-nozzle traverse.
Servo-driven for nozzle traverse, stroke change and core indexing. High slot fill is possible.
High speed and minimized sound, due to newly-developed mechanism to reduce vibration.
High accuracy and durability.
NOL-0160 / NOL-0260
Applicable core : Inside slot motor/Outside slot motor
Nittoku has developed a new machine to wind small outside slot stator cores. Each machine includes Nittoku`s original controller and newly developed AC servomotor technology. The machine has been developed with compact design and easy changeover in mind.
Features
Winding is executed by rotating the nested part on the S-axis, while X, Y, & Z-axis are controlled by the wire nozzle. Different specifications including stack height change, number of poles and number of turns can be altered via PC.
Layered winding is possible due to newly developed wire feed methods.
Nozzle position and wire feeding can be changed throughout every layer of the winding process. This reduces slack, therefore creating better winding condition.
Winding time is reduced as a result of wire feed method. This is possible through intermittent nozzle feed and changing nozzle position throughout the winding process.
Precise positioning of the bridge wire from pole to pole is possible due to the AC servomotor.
This series can be linked with our other machines via our Free Flow transfer system. Processes before or after winding can be fully automated. |
|
Rotary Atomizers
The production-proven, patented Nordson RA-20 and RA-20R rotary atomizers deliver painting efficiency and superior finishing quality and operating safety for a wide range of finishing applications. With no minimum sparking distance, they can be positioned close to parts for optimal coverage and minimal overspray. The fine atomization and soft spray apply thin, controllable film builds with minimal paint bounceback.
With an internal powder supply (IPS), the RA-20R rotary atomizer features lightweight, flexible low-voltage cables that experience less wear in robotic applications.
Close-in painting for superior performance
Excellent spray-pattern control
Sprays a variety of coating materials
Air-bearing turbine ensures reliability
FM-listed as non-incendiary
Patented atomizing cup design for operating versatility
Choice of power supplies for operating flexibility
Easy retrofit to existing painting systems
|
|
|
|
