|
|
|
|
|
|
Application
The oil mist separator OMS is designed for cleaning the air from oil mist during production processes. It is especially
recommended for extraction the oil particles of cooling-lubricating fl uids, that are used for metal machining (e.g., turning,
milling, drilling).
The appliance is not appropriate for capturing the caustic substances that can have a bad infl uence on the device and for
compounds creating explosive mixtures with the air.
Structure
The separator is divided in three chambers, and the air stream is fl owing subsequently through following chambers:
– oil sedimentation chamber – equipped with connection for the oil-saturated air,
– fi ltering chamber equipped with three fi ltering sections,
– fan chamber with a fan with radial impeller and control panel,
– silencer.
In the fi ltering chamber proceeds the three-stage cleaning process of the contaminated air.
First the air stream goes through the labyrinthine fi lter, next is the net fi lter and fi nally through the pocket fi lter of oil-resist-
ant polypropylene. Each fi lter can be easily disassembled and cleaned. The captured oil volume is accumulating in the oil
sedimentation chamber. Underneath this chamber is located the oil drainage valve from where it is collected in a contain-
er* for oil.
In order to reduce the noise level is used a silencer.
During the use a continuous technical supervision is not necessary.
Oil mist separator – OMS-2
* The container for oil is not a standard equipment of the oil mist separator.
|
|
Absolents oil-smoke filter ODR is well suited for use in applications such as:
• Heat-treatment
• Cold-drawing
• Gear cutting
• Grinding with straight oil
• CNC turning with straight oil
• Forging operations and cold pressing
|
|
ARPX Series
POLLUTANTS: DRY DUST - SMOKE -FUMES - ODOURS
AIRFLOW RATE: 2000 ÷ 3200 m3/h
This trailer-mounted series is suitable for suction and purification of dust produced during dry machining processes, when good airflow rates are required and no large amount of dust is created.
Its versatility of use, modularity and mobility make this unit perfect for workshops where the machined materials change periodically.
The AE version is equipped with a High Efficiency HEPA fiter, suitable for the removal of microdust and smoke.
The CA version is suited for the removal of fumes and odours.
The N version is equipped with a drainage and a tank to collect re-condensed coolant.
Pre-arranged to be equipped with an Articulated Self-supporting Suction Arm.
|
|
MISTKOP's proven design couples simplicity with efficiency. No spinning filter to waste horse-power or cause vibrations due to unbalanced filters. Mist and contaminants are captured at the source rather than after they are dispersed as with unducted or electronic units. Easily replaced, low cost filters. Collected fluid drains to your process or container. Usually hung near the source, but all models are available "inverted" such as VC-51 for direct or floor mounting. Secondary filters can be added for smoke.
Easy to install
Increase production efficiency
Low initial cost
Reclaim valuable lubricants
No rotating filters to get out of balance
Non-electronic
MISTKOP with Exhaust Shell vents filtered fumes, gases, or heat to the outside. Available for all models, standard or inverted. Can also be supplied with HEPA filters for efficiency up to 99.97% at 0.3 micron.
|
|
The WS series represents a quality solution for the collection of coolant and oil mist. With 5 sizes, ranging from 250 to 2000 m3/h, it is characterized by a sophisticated design, compact
dimensions and standard accessories.
Specifically developed for the elimination of mist, vapour, smoke and odours typical of wet machining operations these mechanical filters can also be employed in mixed application (wet/dry) and for EDM machines
|
|
Gemini represents the perfect solution for all cases where the customer in little spaces has the need of both a pre and post-filtration.
Thanks to the compact shape, Gemini adaptes very easely to all type of machine tools.
Gemini is supplied with a prefiltration stage and another filter with specific efficiency depending on the needs of the customer (>95% or >99,95% - Norms CEN EN 179/1822).
GEMINI has a particular design, already patented, which makes maintenance operations and filters replacement very easy.
Gemini is really customizable in fact it is possible to have different combinations of filters depending on the desired efficiencies and maintenance intervals even after the first installation.
|
|
ECO Series
POLLUTANTS: OIL MIST - MICRODUST - SMOKE
AIRFLOW RATE: 500 ÷ 750 m3/h
A quality, reasonably sized solution. Suitable for suction and purification of oil mist, microdust and smoke produced during damp and dry machining processes.
The unit is equipped with a drainage for the recovery of recondensed coolant liquid.
|
|
ARF Series
POLLUTANTS : MICRODUST – SMOKE – FUMES - ODOURS
AIRFLOW RATE : 750 m3/h
Suitable for suction and purification of microdust and smoke produced during damp and dry machining processes.
The perfect solution for Laser Machines and Machines for Spark Erosion.
The suctioned air first passes through a sequence of metallic and synthetic filters, which retain the particles with higher granulometry.
Subsequently, the air goes through an Absolute HEPA Filter H13 - tested in accordance with Euro Norms EN 1822 - and is emitted perfectly purified in the environment.
The FA version is equipped with an ACTIVED CARBON cell to eliminate fumes and odours.
|
|
ARNO Series
DESIGNED FOR HIGH-DUTY PRODUCTION MACHINE TOOLS
WORKING ON 3 SHIFTS
guarantee of:
- constructive solidity of its mechanical parts
- 5 filter stages, which can be diversified according to the type of pollutant and kind of machining process
- residual concentration of pollutant in the air at unit exhaust < 0,1 mg/m3
POLLUTANTS: OIL MIST- SMOKE- MICRODUST
AIRFLOW RATE: 1000 ÷ 4000 m3/h
SUITABILITY: ALL TYPES OF MACHINE TOOLS
MACHINING CENTRES - LATHES - GRINDING MACHINES- LASER MACHINES - BORING MACHINES - MILLING MACHINES - THREADING MACHINES – SHARPENING MACHINES - MACHINES FOR SPARK EROSION - COLD HEADING MACHINES - ETC...
|
|
|
|
|
|
Oil mist and fume "compact" filter for centralized plants, capacity 6.000-30.000 m3/h.
SO.TEC "compact" plants are studied to have a little size and a very high separation efficiency.
The filtering process consists of two stages:
• In the former stage graphite and oil particles bigger than 1 micron, as well as any other impurities, are separated from the air flow;
• In the latter stage such submicrone oil particles, making up 90% of total oil present in suction air, are separated by coalescence according to an efficiency factor as per table below:
- 99,9 % efficiency for bigger than 1 micron particles
- 99 % efficiency for bigger than 0,5 micron particles
- 95 % efficiency for bigger than 0,2 micron particles
(high efficiency achieved thanks to the special Microless® filtering elements).
Our well-established know-how and the reliability of our plants enable us to meet our Customers’ needs for extremely low emissions:
- in case of separation of oil mist from hot brass stamping process we guarantee
- in case of filtering of oil mist from machine tool machining, we guarantee an emission oil content lower than 2 mg/Nm3 (expected value lower than 1 mg/Nm3).
|
|
|
|
|
|
Oil mist and fume "supercompact" filter for centralized plants, capacity 20.000-180.000 m3/h.
SO.TEC "supercompact" plants, thanks to the optimum use of the space inside the filter and to the acces doors placed on both sides, are able to garantee high flows capacity with reduced obstruction, maintaining an high separation efficiency.
The filtering process consists of two stages:
• In the former stage graphite and oil particles bigger than 1 micron, as well as any other impurities, are separated from the air flow;
• In the latter stage such submicrone oil particles, making up 90% of total oil present in suction air, are separated by coalescence according to an efficiency factor as per table below:
- 99,9 % efficiency for bigger than 1 micron particles
- 99 % efficiency for bigger than 0,5 micron particles
- 95 % efficiency for bigger than 0,2 micron particles
(high efficiency achieved thanks to the special Microless® filtering elements).
Our well-established know-how and the reliability of our plants enable us to meet our Customers’ needs for extremely low emissions:
- in case of separation of oil mist from hot brass stamping process we guarantee
- in case of filtering of oil mist from machine tool machining, we guarantee an emission oil content lower than 2 mg/Nm3 (expected value lower than 1 mg/Nm3).
|
|
Oil mist and fume Mini-Max filter, capacity 1.500-7.000 m3/h.
The new Mini-Max series filters are studied to be located in proximity of tooling machines or in proximity of hot metal stamping presses with eventual cetralized solutions. Mini-Max filters are composed by a pre-filtration section, by a very high efficiency filtration section for oil mist and fume and by possible further stages for absolute filtration (H13).
Basically the privilege of SO.TEC coalescence filters is the long operating time, continue high filtration efficiency, without any maintenance requirements. On suction from tooling and machining operations, with oil or water-based lubricant, we can also guarantee more than 5 years’ operating time for the coalescence filtration section.
|
|
Oil mist and fume Mini-Max filter, capacity 500-1.500 m3/h.
The new Mini-Max series filters are studied to be located in proximity of tooling machines. Mini-Max filters are composed by a pre-filtration section, by a very high efficiency filtration section for oil mist and fume and by possible further stages for absolute filtration (H13).
Basically the privilege of SO.TEC coalescence filters is the long operating time, continue high filtration efficiency, without any maintenance requirements. On suction from tooling and machining operations, with oil or water-based lubricant, we can also guarantee more than 5 years’ operating time for the coalescence filtration section.
|
|
ECO-WORKCABIN Drawing 1620
Equipped with a PRE-FILTRATION SYSTEM FOR SWARF
It allows the highest degree of cleanliness of the working environment.
Its ergonomic design and the protective screen made of transparent Lexan are essential elements to safeguard the machine operator.
An easily removable swarf collector prevents the diffusion of the removed particles in the working environment and on the clean workpieces.
The cabin is pre-arranged to be equipped on board with an air cleaner for suction and purification of oil mist produced during the process of polishing. As an alternative, oil mist could be removed by the air cleaner installed on the machine tool.
The support trailer can be supplied either with wheels made of rubber or with feet.
The unit can be made soundproof to reduce noise pollution.
In the picture: ECO-WORKCABIN equipped with an ECO air cleaner.
|
|
Centrifugal filter for oil mist CLEANMIST® Filter body, divided into two parts, eases service operations; the inlet is provided with a mesh to avoid aspiration of solid materials and a conic diffuser for uniforming distribution of fogs within the wheel. Fog and vapour particles are centrifuged at high speed inside the wheel and, crossing the filtering panels, undergo a coalescence effect becoming small drops which, joined in a pressure flow, are discharged with the specific drainage.
Cleaned air is discharged in the environment, passing through the upper part of the filter.
|
|
UNIFIL air cleaners stand out for easy installation, easy operation and easy maintenance. Thanks to the well-devised design and the utilization of high quality filter elements, the units achieve long operating times and a collection efficiency of 99.997% for particles >0.3µm
- Modular design:
In case of changing an application, UNIFIL can be adapted any time in a budget-saving way (e.g. further pre-filter plates or gas sorption stages can be connected for the elimination of odours %u2013 in modular design!)
- Flow optimized fans in special collocation:
Optimum inflow into the main filter and use of the entire surface. Replacement of the main filter is only necessary if full load has been achieved, energy consumption is extremely low.
- Easy maintenance:
UNIFIL applies slide-in units for standardized filter elements. This makes maintenance easy and a replacement is done in few minutes
|
|
S-Series tubular bag filter
The Dantherm S-Series budget dust collector range is a simplified version of the long established and respected Dantherm NF wood waste filter family. Quick to install and easy to operate, it is the ideal solution for the smaller workshop. It is designed for indoor locations and can be readily re-located as required
Key features
• Neat, compact, unobtrusive
• Quick and easy to install
• Bag or steel bin dust collection options
• Standard units in three sizes
• One bag size fits all
• Quiet running efficient 1450 RPM fans
• Simple maintenance
• Dantherm QF versatile clip together duct connections
Typical applications
• Woodwork, dust extraction from small and medium workshops
• Mixed workshop applications
• Educational workshops – ceramics, crafts, woodwork,
|
|
| ... products without technical information |
| |
WST fume extraction torches
Air Liquide Welding has developed a range of "all-in-one" tools that provides the main features of MIG/MAG welding torches and effective fixed-collector extraction system for healthy environment for welders and compliance with regulations.
|
|
MIG/MAG-Fume Extraction Torch RAB Plus
MIG/MAG-Fume Extraction Torch RAB Plus 24 KD (air-cooled)
The clean solution for use throughout the metalworking industry.
Arguments speaking for themselves:
- Direct extraction at the arc - for fume removal
- Trouble-free installation in all existing MIG/MAG welding stations
- Small extraction tube diameter - better accessibility
- Handle with extraction control and swivel joint - optimized handling
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
