|
|
In-Line Tube Fans (R)
made of steel
from 100- 400 mm tube diameter
max. V= 5.330 m³/h
max. pt= 900 Pa
easy electrical connection
100% speed controlable
can be installed in any position
Application:
ventilation for residential and industrial zones
In-Line Tube Fans (RS)
made of plastic
from 100- 315 mm tube diameter
max. V= 1.760 m³/h
max. pt= 720 Pa
completely corrosion resistant
100% speed controlable
high pressure
Application:
ventilation for residential and industrial zones
|
|
Axial duct fans EZR/DZR for commercial use: durable, powerful and robust
For ventilation or air extraction of
· Showrooms
· Foreman%u2019s offices
· Workshops
· Production sites
As well as for machine extraction
High degree of protection IP55
Can be fitted in any position
Duct sleeve made of galvanised sheet-steel, with flanges on both sides
Single phase AC version (EZQ/EZS) and three-phase AC version (DZQ/DZS)
Pole-changeable version, for two speeds
Special versions available on request
Air flow volume up to 15,000 m³/h
|
|
| ... products without technical information |
| |
... see all the products in the category
Axial fans
|
| ... products without technical information |
| |
The RXZ-High-Performance separator as a duct element is intended to be installed in ventilation ducts with polluted air. Airvolumes of up to 100000m³/h. The separators can not only be integrated in the ducts but also, for example in a central for the exhaust air. All devices have chamber of inspection doors which are easily accessible. For maintenance purposes the filters can be completely removed.
Used as general air separator, the RXZ-High-Performance separator takes in air, both from one side and two sides , and cleans it in its basic element. Depending on the air flow volume the general air separator can be equiped with several basic elements. The discharge of the pollutants is by a common pipe. The elements are also available as complete units with fan.
|
|
Richco's Slit Harness Wrap (SHR) is the answer to cable management problems in industrial applications, where the jumble of cables can be unsightly and dangerous.
The SHR is a revolutionary system that enables cabling to be tidied and managed in seconds via the use of a special applicator tool. The SHR can be removed at any time and is totally reusable.
|
|
|
Tubing protection with closing system for mecanical, EMI/RFi or thermal protection Diameter between 9 and 100 mm
|
|
Optical Fiber Flexible Guide System
Features
●Fully modular system giving complete fiber
management and protection at PCB level applications
●For use with 250 and 900 micron fiber
●Fibercan enter and exit at any point, without risk of fibersnagging or kinking
●Angled and straight lugs located along the top of the guide preventing fiberfrom springing out
●‘Snake’the guide through and over components, where space is limited
●Flat and raised supports available, other support post heights and panel thicknesses available by special order
|
|
These divisible connectors are suitable for repairs or where cable protection systems have to be installed after wiring.
The divisible connectors in connection with the divisible conduits and divisible lock nuts are responsible for the highest possible mounting flexibility.
|
|
Combustion Chambers
standard or custom-built combustion chambers.
especially designed to allow a flame inside
short heat-up and cool-down times
designed for optimum burner performance.
available in various materials.
adapted to customers process.
Commissioning & After Sales Service
MAXON combustion systems and equipment have been engineered for a minimum of maintenance.
MAXON can provide technical support during and after commissioning in almost every corner of the world through a broad international network of offices and representatives.
All MAXON offices have a stock of common spare parts, allowing MAXON to respond quickly to parts requests.
|
|
ECOSTAR DUCT, PROCESS BURNERS
Production as per DIN 4787-4788 and European standards
CE other certificates
- Low emission values
- Silent operation
- Superior Design
- High efficiency
- High technology
|
|
|
The M.A.S. injection system creates single air jets. Between these air jets zones with negative pressure are created. In this way hot secondary air is drawn strongly into the flame. Thus provides a quick and homogenous mixing of secondary air with fuel and combustion gases, a rapid ignition, a hot sharp flame, best heat transfer to the clinker bed and excellent burn out conditions.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
tesa offers a variety of coated cloth tapes and non-woven tapes, whose characteristics include flexibility, residue-free removal, and high adhesive levels on many surfaces. They have high physical and chemical resistance and are ideal for applications requiring abrasion resistance and waterproof traits.
|
|
* All cloth tapes are strong and offer good conformability
* All cloth tapes from Advance Tapes have non-corrosive adhesives keeping any reaction with the surface applied down to a minimum
* Some cloth tapes will peel clean from surfaces, usually polycoated tapes perform better in this respect although surfaces should be tested if this is critical
* If you wish to write on the tape for identification purposes, uncoated cloth tapes may be the best choice. Alternatively, tapes with a matt surface will perform better than gloss coated tapes. Please request a sample to test if this is an important factor in choosing the tape
* Cloth tapes should be applied at between +10°C and +40°C
* Surfaces should also be as clean and dry with any loose material and dust removed as far as possible
* Tapes should be stored at a temperature of no lower than +5°C. If tape is left in a van or unheated warehouse in the winter months, it will need time to warm up prior to application
* The most popular colours for cloth tapes are black, silver and white. For a much wider range of colours, polycoated tapes offer the best choice.
|
|
tesa offers a variety of coated cloth tapes and non-woven tapes, whose characteristics include flexibility, residue-free removal, and high adhesive levels on many surfaces. They have high physical and chemical resistance and are ideal for applications requiring abrasion resistance and waterproof traits.
|
|
|
Cleaning with a robot has many advantages. The operator can see where the robot is travelling, what needs to be cleaned and what has been cleaned. A high resolution colour camera placed on a flexible arm enables the camera to be positioned where it is best suited. Positioning the camera behind the robot platform gives the operator a full view of both sides of the brushes and the ductwork that is being cleaned...
|
|
|
This bench shearing machine cuts plastic covers and raceways up to 125 mm wide perfectly without burring.
|
|
|
Design2FAB is a flexible, easy-to-learn and easy-to-use solution for creating HVAC duct, mechanical, kitchen, industrial, roofing or specialty fitting layouts. Engineered to dramatically reduce the time it takes to develop and lay out flat patterns, Design2FAB is known for its superb versatility. You can create complex custom fitting layouts in minutes, not hours! Design2FAB provides you with the ability to create HPGL and DXF output formats. You can use a plotter to print the HPGL layout for manual cutting by hand or use a CNC cutting machine to produce fittings from the DXF files. Prior to CNC cutting, DXF files may be exported to TurboNest or ProNest nesting software for optimal material utilization.
|
|
| ... products without technical information |
| |
|
The Jetvent Duct Cleaner by Triventek is the result of many years experience in the ductcleaning industry. It combines the strength of a powerful industrial engine with a light weight compact design which together with special shaft technology provides a long term solution for safe and comprehensive cleaning of ductwork...
|
|
|
