|
|
APPLICATION:
To control the flow of Hot Liquids, Hot Gases, Cryogenics** and any other fluids not reactive with construction materials and free of sediment. Cryogenic fluids include Liquid Oxygen (-297°F), Liquid Argon (-303°F) and Liquid Nitrogen (-320°F). Valve operates from zero to maximum differential pressure indicated in table. Valve must be mounted in horizontal pipe with solenoid enclosure vertical and on top.
OPERATION:
Valve closes when energized and opens when de-energized. When the coil is energized the plunger presses the poppet, closing the pilot orifice, and opens a bleed passageway to permit pressure to build above the piston and seal it. Upon de-energizing the coil, the pilot orifice is opened, relieving the pressure above the piston allowing it to leave its seat. The bottom spring allows the valve to operate at zero pressure drop.
|
|
APPLICATION:
To control the flow of Corrosive Fluids, Deionized Water, Condensate, Ammonias, Vegetable Oils, Fuel Oils, Cryogenics**, Flammable Liquids. Cryogenic fluids include liquid oxygen (-297ºF), liquid argon (-303ºF) and liquid nitrogen (-320ºF). Valve operates from zero to maximum differential pressure indicated in table. Valve must be mounted in horizontal pipe with solenoid enclosure vertical and on top.
OPERATION:
Valve opens when energized and closes when de-energized. When the coil is energized the pilot valve opens, relieving the pressure above the piston, which is then lifted from its seat by the plunger. Upon de-energizing the coil, a spring closes the pilot valve and opens a bleed passageway to permit pressure to build above the piston and seat it.
|
|
APPLICATION:
To control the flow of Water, Air, Gas, Solvents, Vacuum and any other fluids not reactive with construction materials and free of sediment. Buna N seating of the main orifice make the valves ideal for TIGHT SEATING, LOW PRESSURE and LOW FLOW conditions. Valve operates from zero to maximum differential pressure indicated in table. Valve must be mounted in horizontal pipe with solenoid enclosure vertical and on top.
OPERATION:
Valve opens when energized and closes when de-energized. In this direct acting valve the disc holder assembly is lifted from its seat by the plunger.
|
|
APPLICATION:
To control the flow of Water, Oil, Air, Gas, Solvents, Brine, Vacuum and any other fluids not reactive with construction materials and free of sediment. Valve operates from zero to maximum differential pressure indicated in table. Valve must be mounted in horizontal pipe with solenoid enclosure vertical and on top.
OPERATION:
Valve opens when energized and closes when de-energized. When the coil is energized the pilot valve opens, relieving the pressure above the piston, which is then lifted from its seat by the plunger. Upon de-energizing the coil, a spring closes the pilot valve and opens a bleed passageway to permit pressure to build above the piston and seat it.
|
|
|
|
|
|
The Magna Flow Control Valve with an easy to read micrometer dial offers an amazing 1100 precise set points to accurately control flow of gases or liquids. The extremely high CV of the Magna Flow control valve enables very high flows for whatever media is being controlled, up to 200 PSIG pressure or full vacuum. Linear flow characteristics provide easy to set and precise metering of gases and liquids for almost any application where accurate results are required.
Available in either light weight impact resistant nylon or clear polycarbonate construction, the Magna Flow Control Valve offers superior strength and corrosion resistance, making it ideal for use in hundreds of different applications. Simplicity of construction, with removable top and bottom caps, provides easy disassembly for cleaning or maintenance without removing the valve from service. Proven O-ring seals provide a positive zero tight shut-off. Replacement of seals, if required, is quick and easy because disassembly is simple and fast. The Magna Flow Control Valve offers all these features at a very affordable price.
|
|
|
These valves are specifically designed to use for safe pressure gauge installation. The bleed or vent screw is used to vent the pressure with out opening the connections.
|
|
Description:
The Becker Series CVE & 41005 Globe Valve Regulator’s innovative design makes it among the most versatile natural gas contral valves in the world. Its cage-guided design utilizes multi-interchangeable trim styles, eliminating the need to change body styles. The Becker Globe valve is available with balanced or un-balanced trim for natural gas regulating applications such as pressure and flow control. Body styles provide a choice of flanged, buttweld, or threaded valve end connections.
|
|
V-Series Two-way and Three-way Globe Valve Bodies
The high quality V-Series two-way and three-way globe valves are manufactured to exact specifications and are designed to provide years of reliable service. The assemblies are designed for heating/cooling applications using steam, water, glycol or other non-corrosive fluids. The V-Series assemblies should not be used with combustible fluids such as natural gas. The V-Series products are available as complete assemblies but most users purchase the bodies, actuators and linkages separately for convenient local assembly.
Features
- Heating and cooling applications for non-corrosive fluids
- Steam and hot water flow control
- Complete valve assemblies or components available
- Electric actuators and linkages
- Two-way flow and three-way mixing and diverting valves
- 1/2" to 6" valve sizes
|
|
Features
* High flow capacity & rangebility
* Large type of trim designs for various duty conditions
* Top opening for easy trim inspection without disturbing the piping.
* Tight closure even in extreme operating conditions
* Designed and tested to deliver 100% performance under specified operating conditions
* Wide selection of actuators to meet most requirements
|
|
2-Way & 3-Way
Screw & Flanged Style Bodies for Temperature Controls & HVAC, Hot Water, Steam & Chilled Water
|
|
Globe Valves, PN16
Bronze body, screwed topwork in brass
Part No. 03021.X.0160
Part No. 03021.X.5160 Globe/Check Valve
Flanged connection acc. to DIN EN 1092-1 PN16
Applications:
Suitable for non-toxic, non-inflammable fluids, gases and vapours.
The laws, regulations and standards are to observe for the range of application.
Working temperatures and pressures:
up to max. 16.0 bar: -10°C / +14°F (263K) up to +80°C / +176°F (353K)
up to max. 10.0 bar: -10°C / +14°F (263K) up to +120°C / +248°F (393K)
up to max. 6.0 bar: -10°C / +14°F (263K) up to +160°C / +320°F (433K)
|
|
21000 Series
Masoneilan's 21000 Series control valve is a heavy top guided globe valve design featuring noise attenuation and anti-cavitation trim options. It is the most versatile single ported control valve on the market today, well suited to handle a wide variety of process control applications.
41005 Series
Masoneilan's 41005 Series control valve is a cage-guided globe valve design with balanced trim configurations. This product line is engineered to efficiently handle demanding process conditions, including applications with high-pressure drops and large temperature variations.
|
|
ARI-FABA Long Life
Application: Industry, powerstations, flue gas purification plant, processing technology, gas supply, vapour facilities, recycling facilities, vacuum facilities, hot water, heating technology, district heating, thermal oil applications, general plant manufacturing, etc.
Medium: Steam, gases, hot water, thermal oil, process water, vacuum facilities, ammonia etc.
Application (Stainless Steel): Recycling facilities, chemical industry, hospital technology, process water installations, installations with aggressive media
Medium (Stainless Steel): Process water, aggressive media, etc.
eClass-No.: 37010201
|
|
GLOBE VALVE,
SS316/304/WCB BODY,
FLANGED END OR THREADED END,
PRESSURE PN16/40, ANSI150/300 OR
200WOG
|
|
|
Bronze Globe Valves for use in commercial and industrial applications. Typical services include; hot and cold water, HVAC, steam, compressed air, gas and other general utility services.
|
|
Flowserve's Vogt Globe and Angle valves are suitable for throttling as well as shut-off. They are customarily installed so that the media pressure and preferred flow direction is under the disc. Flow above the disc is also accecptable.
Vogt Globe Valves are available with a variety of bonnet types, body and trim materials and stem packings in addition to a broad range of pressure classes, and end connections including extended bodies.
Our facility is qualified under the most stringent ISO 9001 quality standards and European Pressure Equipment Directive and meets specifications including ASME B16.34, API602 and NACE.
Features
* Quick Lead Times
* Valves for services including: Nuclear, Alkylation, Sour Service, Cryogenic, Low Temp. and more.
* Qualified under the ISO 9001 Quality System & European Pressure Equipment Directive
* Hard Faced Seats
* Spiral Wound Gasket or Bellowseal
* Bolted Bonnet or Seal Weld Bonnet
|
|
Emerson's ACK check valve is a normally closed magnetic check valve that prevents reverse refrigerant flow in liquid lines and compressor discharge lines.
The ABV Refrigeration Ball Valve isolates suction, discharge, and liquid line pipework during maintenance shutdown periods.
|
|
- Hand operated or air operated valves.
- Working pressures up to 14.000 bar / 200,000 psi.
- Large orifices at rated pressures.
- Excelent flow capacity performance.
- Safety quaranteed by special safety cover.
- Smooth operation under pressure.
- High quality stainless steel.
- Panel mounting or in line connection.
- Suitable for fluids or gases.
WE ARE LOOKING FOR A DISTRIBUTOR IN ITALY. Please contact us if you are interested!
|
|
|
This type of valves are designed for heavy duty applications. These valves are widely used in the high pressure testing equipments. Other design features are similar to ANV 1
|
|
The VMP30H is a multipurpose, mini poppet, pneumatic dispensing valve designed for dispensing low to mid-high viscosity fluids, such as silicone dispensing, RTV dispensing, epoxy dispensing, rubber adhesive dispensing, grease dispensing and dispensing of fluids with fillers.
Features
• Designed for low to mid-high viscosity materials
• Stroke adjustment provides shot size control
• Suck-Back eliminates post-dispense "dripping"
• Separated wetted parts reduces maintenance
• Ideal for filled material
|
|
Microvalves
Nominal orifice 2.5 mm
Nominal flow rate at 6 bar 100 Nl/min
Temperature range max +60°C
Working pressure 2 ... 10 bar
Actuating force ~ 6 N
Fluid 50µ filtered, lubricated or non lubricated air
Materials
* Body: aluminium 11S
* Internal parts: brass OT 58
* Seals: NBR
* Springs: stainless steel
|
|
General description :
Electronicaly controlled electromotive dosing valve Series M 3521 C is designed for accurate dosing of gas chlorine into the water.
Electromotive dosing valve Series M 3521 C is made of: compact plastic, resistant to high concentration of chlorine, precision silver dosing valve and quality driving motor.
O-rings and diphragms are made of fluourocarbonic hydrogens ( VITON, TEFLON, EPDM) resistant to agressive gases. All this guarantees a long and accurate functioning of electromotive dosing valve.
|
|
- DN 40 up to DN 300
- PN 16 up to PN 160
- Large material selection
- Different types
- Electrical actuator with 1500 kgf
Applications
For throttling. mixing and distribution of liquids and gases
Main attributes
Cast Iron GG25 (only PN 16)
Spheroidal graphite iron GGG 40.3 up to PN 25
Cast steel GS-C 25 or up to PN 160
Stainless steel (1.4401) up to PN 40
Cast alloy steel GS17 CrMo 55 from PN 64
|
|
Motor valve for on/off- and control operation with neutral and aggressive fluids. Universal actuator designs and flexible accessories. Alternative to a pneumatic valve to avoid compressed air supply.
|
|
|
The H99 & H99HP Series offers a general-service valve of rugged design and construction. It is available in stainless steel to suit a wide range of services. Capable of withstanding high pressures (10,000 psig max and high temperature), this valve is typically used in severe service, high pressure sampling systems, high pressure shut down systems and test stands.
|
|
KOFLOC 2204
The KOFLOC Variable Primary Pressure Flow Controller MODEL 2204 SERIES is a control valve for precise control of minute gas flow and maintaining constant flow under fluctuating primary pressure (inlet), provided the secondary (outlet) pressure remains constant. This characteristic makes it a must-have preliminary valve in many flow control mechanisms. Constructed using high precision parts, the design of the MODEL 2204 SERIES transforms the rotation of the regulating screw to into linear motion of the needle without subjecting it to gaps and vibrations produced by the screw, to ensure stable and even control of minute flow.
FEATURES
♦ Excellent flow stabilization
♦ Clean construction
♦ Independent from supply pressure fluctuations
APPLICATIONS
♦ Scientific instruments
♦ Environmental analysis
♦ Atomic absorption spectrometry
♦ Gas chromatography
♦ R&D
♦ General industrial use
|
|
|
|
|
|
Pin valves
This pin valve is the evolution of article 009, one of the first articles projected and constructed by Ratti.
It immediately differentiates from other valves on the market due to the fact that there is no packing between the body, the valve and the support of the stem.
This solution, introduced over 30 years ago, has allowed us to guarantee a longer life of the valve, in fact the lack of an elastometer in such a critical position, and the realization of a metallic support, provides the valve with greater reliability in terms of tightness.
The only packing present in these valves is the PTFE compass, positioned on the top to support the stem.
The external part of the valve body has been completely re-designed from a "square" shape to a more "round" shape, in order to eliminate the external edges, thus reaching a better shape and making the constructive process more efficient, reliable and economical.
The valve is filed from a full sturdy 316L full bar of European certified make.
In the "053" version the connections are gas cylinder female die screw-cut and the diameters available are as follows: 1/4", 3/8",1/2",3/4", and 1".
In the "049" version the connections are of 3/4", 1", 1.1/2" and 2" "Tri-Clamp" type and the gauges are the same of the diaphragm valve (Art. 061) to favour interchangeability without modifying the plant.
Upon request, Articles 053 and 049 may be furnished with fastenings to be welded.
|
|
|
These needle valves are an ideal option for isolation or throttling application. The self centering non rotating stem ensures perfect seating. These rigid valves are designed for repetitive bubble tight shut off, easy maintenance & long trouble free life.
|
|
'PRIME' Needle valves are made for various operating pressure and temperatures. Looking at ever increasing demand and variety of applications, we have developed special purpose valves for instrumentation and flow control application.
DESIGN: Needle valves are also known as isolation valve, shut off valve or regulatory valve. Rotating angle tipped spindle, which in turn moves axially over the orifice seat, controls flow of the fluid. At the lower most position or closed position of the spindle, inlet orifice is completely blocked and thus isolates the fluid flow. In open condition Teflon or Grafoil packing seal restricts the leakage from the bonnet end.
|
|
|
|
