|
|
| ... products without technical information |
| |
Mechanical presses with excentric drive offer a motion diagram very close to a sinus curve.
Stroke can reach 1000 mm or more; nominal press capacities can be available even 80 or 100 mm over bottom dead center.
his drive is the most traditional one and since years it remains the right answer to a wide range of stamping operations. |
|
... see all the products in the category
Presses
|
Modern IS machines rely on Take Out Arms to efficiently and accurately transfer hollow glassware from the dead plate to the machine conveyor. When functioning properly, the take out arm is synchronized with blow molds and glassware is uniformly spaced on the conveyor. As production rates and line speeds increase, the proper functioning of the take out arm becomes especially critical.
- Fully compatible with most IS machines
- Built in overload protection option
- Maintenance free
- Greatly improved drive life
- Complete drive or retrofit kits available
- Reduced downtime and maintenance
- Suitable for 4.25" to 9.25" bottle spacing
|
|
The new products in the PC-RSD-PCI Series are plugged each into a PCI bus slot on the PC to serve as a new type of silicon disk drive using a CompactFlash (CF) card in the same as a hard disk.
The PC-RSD-PCI Series has two CF card slots on the board, one of which comes standard with a CF card. The other slot is available between the PCI board brackets, allowing an additional CF card to be plugged and unplugged as a removable disk with the board installed on the PC. The second slot can extend the range of applications, such as separating the OS and data areas.
The PC-RSD-PCI board uses a highly reliable CF card (fixed disk mode), which can be partitioned into two or more drives. The PC-RSD-PCI board can also accommodate an optional additional CF card to add an additional drive or drives (thereby increasing the total capacity), in which case the two CF cards can be configured into a RAID by striping (RAID level 0), mirroring (RAID level 1), or spanning (JBOD) using a utility. The PC-RSD-PCI Series is a line of 1 GB, 2 GB, and high-capacity 4 GB and 8 GB models. These are designed environment-conscious to be lead-free and to (be scheduled to) conform to the RoHS Directive.
|
|
KRAL pumps with magnetic coupling are hermetically tight, the pump station as well as the site itself stays clean. As magnetic couplings work without wear and maintenance-free, the life cycle costs are favourable comparative to conventional sealing systems.
Please consider that we are a manufacturer of high quality displacement pumps and flowmeters for liquids. The products (pumps with magnetic couplings, high pressure flowmeters and flowmeters – chemically resistant) mentioned on this portal are only part of our product range. Please find more detailed information on our website or directly from us. |
|
| The ISA range of Inverter power supplies provides the highest level of control available today in large scale resistance welding. The ISA-500AR, ISA-1000AR and ISA-2000AR are intelligently packaged in “NEMA” style enclosures and are designed to deliver robust performance in the harshest of production environments. The ISA models can deliver 500, 1000 and 2000 amps of primary welding current, respectively. |
|
| Sumitomo's Cyclo Helical Buddybox (Cyclo HBB) combines the long-proven Cyclo reducer and a single stage offset parallel helical gearbox in a rugged integral, shaft-mounted design. The HBB incorporates the strength and flexibility of the Cyclo reducer with the adaptability of a shaft-mounted, reducer. With a 24-month warranty, regardless of hours of operation, the Cyclo HBB is an excellent choice for applications in material handling, shredders, specialty machine industries, conveyors, and other applications requiring a simple, convenient shaft mount reducer. |
|
The CPU-H Unit is distinguished above all by its large, central hollow shaft. The hollow shaft can be used to pass cables, shafts, welding wire, compressed air, vacuum, grease, oil or even Laser beams through the centre of the gear. In addition this Unit exhibits improved gear accuracy, higher maximum rotational speeds and a large, stiff and precise output bearing that functions simultaneously as housing. Improved corrosion protection allows use even in extreme environments.
Advantages:
- Gear Transmission accuracy improved by up to 50%
- Newly developed extremely precise, high capacity and high stiffness output bearing
- Complete corrosion protection
- Viton shaft seals for the output bearing with additional protective lip
- Output compatibility with the various CPU and CHA Series
- Zero backlash, high torsional stiffness and excellent repeatability
- High torque capacity
- Compact design and light weight
- Long operating life
- High efficiency
- Quick assembly and simple installation
- Maintenance-free with lifetime grease lubrication |
|
Paramax® helical and bevel gears of the standard Paramax range and the various special Paramax versions are the outcome of six decades of experience in drive engineering. By virtue of the modular design, they permit use under difficult and severe conditions even in the most diverse applications. The Paramax® product range consists of the standardized 9000 series as well as the special SFC designs for cooling tower drives and compressors and SEC for extruder drives.
With 26 sizes in the Paramax® 9000 series, an application can be precisely designed according to the performance, torque and velocities, thus ensuring a long service life and cost effective, powerful operation. |
|
| The Sumitomo Helical Shaft Mount (HSM) Speed Reducer provides a convenient installation and removal method for speed reduction by mounting directly on the drive shaft. Sumitomo's Taper-Grip® bushing design provides simple keyless mounting and easy removal. HSM is readily adaptable for CEMA screw conveyer and shaft mount options. The HSM features carburized gear teeth with optimal gear geometry and wide gear faces, allowing maximum loading and highest efficiency torque output, for higher rating capacity in the most compact design. |
|
Mini reducer under casing CSF
A component last generation (standard HFUC) associated with a powerful bearing of exit (at 4 contact points). From 20 with 48mm for a couple max from 1,4 to 28 Nm.
Benefit produced:
* Reducer with null play. It is particularly compact with a bearing of exit at 4 contact points and a strong integration of the reducer in the casing
* Particularly compact with a bearing of exit at 4 contact points and a strong integration of the reducer in the casing.
Characteristics produced:
* C max from 1,4 to 28 Nm
* Report/ratio of reduction from 30 to 100
* Diameter X length of 20x17 with 51x45
* Very high compactness (component last generation) and bearing of exit at 4 contact points.
* 3 versions: - adaptation engine in entry and flask of exit (2XH-F),
- adaptation engine in entry and output shaft (2XH-J),
- tree of entry and output shaft (1U)
Sectors of use:
* Robotics,
* Special machines,
* Semiconductors,
* Machines of assembly. |
|
REDUCER CPU-M
Reducer under casing associating a reducer without play Harmonic Drive with a bearing of exit of large diameter with cross rollers.
Range CPU is a family of product, the version - M adapts to all the engines of the market. We adapt the hub to your driving shaft. The driving whole + reducing under casing CPU-M is particularly compact.
Benefit produced:
* Adaptability with all the engines of the market.
* Compactness of the assembly.
* High strength of the bearing of exit of large diameter to cross rollers
Characteristics produced:
* Couples of exit until 1840Nm,
* Radial force on the bearing of exit until 38.400N, length max 84mm.
* Utmost precision,
* Compactness of the assembly, adaptability to all the engines.
Sectors of use:
* Robotics,
* Machine tools,
* Special machines |
|
Cone Drive has a range of gear coupling solutions to meet our Customer's requirements for integration into our gearboxes or to supply on a replacement basis.
A torsionally rigid, lubricated design that offers high torque capacity, application versatility, and where high torque loads exist or shaft diameters exceed 100mm, the lowest initial cost. Available in 28 sizes, and all featuring triple-crowned teeth, David Brown gear couplings offer the industry leading torque ratings (over 8 million Nm) and the largest bore capacities (up to 1025 mm).
- Type GC02 & GC05 Continuous Sleeve Couplings - Features a one-piece, low profile sleeve encompassing the hubs. Economical and compact they are available in both close coupled and floating shaft models.
- Type G/GF32 Spacer Coupling - For pumps and compressor applications, provide ease of servicing 'connected' equipment.
- Type G/GF52 Floating Shaft Coupling - Used when distance between equipment is too great for spacer couplings. Two single engagement couplings with interconnecting shaft. Also available for vertical mounting.
- Type G/GF20 Close - Coupled Double Engagement Coupling - Design with 2 flex halves to accommodate both offset and angular misalignment. Also available for vertical mounting. |
|
| With safety becoming an increasingly important factor in the design and manufacture of equipment, it has become necessary to add a brake to many critical machine functions. In response to that concern, White Drive Products offers the BK10 Series brake. All internal components, including roller bearings, brake disks, springs and seals were chosen for maximum durability. To further extend the life of the unit and reduce noise, all internal components run in an oil bath. Two brake release ports are also provided to simplify plumbing and bleeding of the brake release circuit during installation. All of these features combine to make the BK10 Series brake the top choice for any static brake application requiring 10,000 lb-in of holding torque. |
|
|
... see all the products in the category
Brakes
|
FD - FLOW DIVIDER / 950 Series
White Drive Products flow dividers represent an ingenious use of the patented Roller Stator® gerotor assembly. These highly effective devices use a common housing to supply the input flow to two gerotor assemblies linked by a common drive link. By linking the two gerotor assemblies together, accurate splitting of the flow is assured. These flow dividers use no bearings or rotating seals, eliminating the typical failures in other designs. By using the highly efficient Roller Stator® gerotor elements, high efficiencies are maintained, even at low flows. Because White Drive Products flow dividers work at much lower RPMs than most gear dividers, they are noticeably quieter. These flow dividers are an excellent way to synchronize cylinders or motors. Because they tolerate higher output pressure differentials than other designs, they may also be used for pressure intensification by connecting one output to tank.
|
|
Horizontal, vertical, diagonal. This tried and tested semi-automatic welding machine can be used universally. The increased welding speed compared with hand welding gives rise to higher productivity.
• Overlap welding of PVC-P, ECB, EPDM, CSPE and TPO roofing membranes
• Faster and more efficient than hand welding
• Small and compact
• Steplessly adjustable speed for high welding seam quality
• Can be used in the most confined spaces
• Different welding seam widths
|
|
|
|
