|
|
Features
... fibre-optic cables
High-quality glass fibre-optic cables with silicon-, metal- or PU-coating
Resistant to high temperature (from -40°C to +180°C)
High resolution
Large scanning or sensing ranges
Flexible probes
Lateral light outlet
Silicone-metal sleeve for high mechanical loads and high protection class
Auxiliary optics can be used
Fibre layout rectangular, coaxial, statically mixed
... fibre-optic amplifiers
Robust die-cast zinc casing
Application as diffuse reflective sensor or through beam sensor
Scanning ranges up to 200 mm, sensing ranges up to 1800 mm
Sensitivity, scanning range and sensing range adjustment via multi-turn potentiometer or teach function
High operating frequency
High ambient light immunity due to pulsed emitted light
Green light variety for glass detection
Output function switchable or antivalent
Devices with timer function using time module
Short circuit and incorrect connection protection
Customer-specific versions
|
|
Manlight proposes a wide variety of Erbium (1,5µm) or Ytterbium (1µm) doped fiber amplifiers either using PM or non PM fiber.
Available in OEM module of different sizes depending on the power (with power up to 35dBm at 1,5µm and up to 43dBm at 1µm) as such as in benchtop 3U 1/2 19" (up to 40dBm at 1,5µm) or 3U 19" (up to 43dBm at 1µm), you will necessary find the product that you need for your application.
|
|
general data actual range Sb (FSE 200C1002) 160 mm
sensing distance Tw (FUE 200C1003) 45 mm
light source pulsed red LED
light indicator LED yellow
alignment / soiled lens indicator flashing light indicator
adjustment Pot 270°
wave length 660 nm
suppression of reciprocal influence yes
electrical data response time / release time < 1 ms
voltage supply range +Vs 10 ... 30 VDC
current consumption max. 30 mA
current consumption typ. 20 mA
voltage drop Vd < 1,8 VDC
output function light / dark operate
output current < 100 mA
short circuit protection yes
reverse polarity protection yes
mechanical data width / diameter 10,4 mm
height / length 27 mm
depth 14 mm
type rectangular
housing material plastic (ASA)
ambient conditions operating temperature -25 ... +55 °C
protection class IP 40
|
|
general data version fast version
actual range Sb (FSE 200C1002) 140 mm
sensing distance Tw (FUE 200C1003) 40 mm
light source pulsed red LED
light indicator LED green
alignment / soiled lens indicator LED green, flashing
output indicator LED yellow
adjustment Teach-in
wave length 660 nm
electrical data response time / release time < 0,05 ms
voltage supply range +Vs 10 ... 30 VDC
current consumption max. 45 mA
current consumption typ. 40 mA
voltage drop Vd < 1,8 VDC
output function light / dark operate switchable
output circuit PNP
output current < 100 mA
short circuit protection yes
reverse polarity protection yes
mechanical data width / diameter 12 mm
height / length 33,2 mm
depth 60 mm
type rectangular
housing material PBT / PC
connection types connector M8, 4 pin
ambient conditions operating temperature -25 ... +55 °C
protection class IP 65
|
|
|
|
|
|
Special features
Easy, intuitive adjustment
Bright 2x 4 digit display
Version with M8-connector
Integrated lock functions
Version with external teach-in and integrated teach-in feedback
The newest Series 67 line of fiber optic sensors is attracting much attention thanks to its simple, intuitive operator interface. Simply pressing the teach-in key twice allows two different objects or contrasts to be "learned" by the sensor. The bright, 2x4 digit display simultaneously shows the taught switching point as well as the relative receiving light level. Just like a potentiometer, the switching point can be changed at any time by using the +/- key. Two different security features protect the sensor against unintentional manipulation during ongoing operation: One is a complete lock, while the other option only allows access to the teach-in and manual switching point adjustment, while locking out all other adjustments such as light/dark operation, timer functions or the operating mode with defined response time. The new fiber optic sensor also boasts a wide variety of application possibilities. With a response time of only 50 microseconds it is among the fastest fiber optic sensors available on the market and therefore lends itself to high-speed processes. The integrated 12-bit A/D converter provides high resolution even in large ranges up to 4 m.
|
|
Main Features & Applications:
- 1529-1563 nm Bandwidth
- Fast Transient Gain Control Up to 12 dB
- Up to 12dB Mid-Stage Loss budget
- Compact Package
- Variable Gain
- Excellent Flatness APC, AGC, ACC modes
- For: Long-Haul and Ultra Long-Haul Applications
|
|
|
The EFA-series of benchtop EDFAs are repackagedversions of the high-performance optical amplifiers found in MPB's repeaterless-link telecom equipment. These wall-plug units include preamplifiers with high gain and near-quantum-limited noise figure, as well as power amplifier models with saturated output powers up to 23 dBm.
|
|
The Manlight High Power Amplifier for CATV and FTTx applications
offers a cost effective solution in bringing the bandwidth closer to the end users. With a unique design based on Manlights in-house pump combiner and optical know-how, the high power amplifiers are optimized to offer high power and low noise figure with proven reliability and quality. The output power can be distributed
between 1 to 16 output ports.
The use of efficient and reliable uncooled pump diodes allows the Manlight amplifiers to reach high output powers with low overall power consumption. The control electronics featuring alarms, automatic
shutdown, and RS-232 communication interface is driven by a 5 / 24 VDC power supply.
|
|
BaySpec's IntelliGain® and IntelliSense® Erbium-doped Fiber Amplifiers (EDFA) are designed and manufactured in the U.S.A. to meet stringent Telcordia GR-1312 requirements for reliability and performance.
A compete line of EDFA gain modules are available, designed to meet various amplification requirements for single-channel, narrowband, and DWDM transmission in metro, long-haul and ultra long-haul networks.
Features:
- Output power from 10 to 26 dBm
- Fast transient response
- Gain flatness
- Very low noise figure
- Variable gain
- Mid-stage access
- Selection of industry standard packages
- Ultra low power consumption
|
|
| ... products without technical information |
| |
Manlight proposes a wide variety of Erbium (1,5µm) or Ytterbium (1µm) doped fiber amplifiers either using PM or non PM fiber.
Available in OEM module of different sizes depending on the power (with power up to 35dBm at 1,5µm and up to 43dBm at 1µm) as such as in benchtop 3U 1/2 19" (up to 40dBm at 1,5µm) or 3U 19" (up to 43dBm at 1µm), you will necessary find the product that you need for your application.
|
|
Main Features & Applications:
- 1529-1563 nm Bandwidth
- Fast Transient Gain Control Up to 12 dB
- Up to 12dB Mid-Stage Loss budget
- Compact Package
- Variable Gain
- Excellent Flatness APC, AGC, ACC modes
- For: Long-Haul and Ultra Long-Haul Applications
|
|
|
The EFA-series of benchtop EDFAs are repackagedversions of the high-performance optical amplifiers found in MPB's repeaterless-link telecom equipment. These wall-plug units include preamplifiers with high gain and near-quantum-limited noise figure, as well as power amplifier models with saturated output powers up to 23 dBm.
|
|
The Manlight High Power Amplifier for CATV and FTTx applications
offers a cost effective solution in bringing the bandwidth closer to the end users. With a unique design based on Manlights in-house pump combiner and optical know-how, the high power amplifiers are optimized to offer high power and low noise figure with proven reliability and quality. The output power can be distributed
between 1 to 16 output ports.
The use of efficient and reliable uncooled pump diodes allows the Manlight amplifiers to reach high output powers with low overall power consumption. The control electronics featuring alarms, automatic
shutdown, and RS-232 communication interface is driven by a 5 / 24 VDC power supply.
|
|
BaySpec's IntelliGain® and IntelliSense® Erbium-doped Fiber Amplifiers (EDFA) are designed and manufactured in the U.S.A. to meet stringent Telcordia GR-1312 requirements for reliability and performance.
A compete line of EDFA gain modules are available, designed to meet various amplification requirements for single-channel, narrowband, and DWDM transmission in metro, long-haul and ultra long-haul networks.
Features:
- Output power from 10 to 26 dBm
- Fast transient response
- Gain flatness
- Very low noise figure
- Variable gain
- Mid-stage access
- Selection of industry standard packages
- Ultra low power consumption
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
