|
|
Manlight proposes a wide variety of Erbium (1,5µm) or Ytterbium (1µm) doped fiber amplifiers either using PM or non PM fiber.
Available in OEM module of different sizes depending on the power (with power up to 35dBm at 1,5µm and up to 43dBm at 1µm) as such as in benchtop 3U 1/2 19" (up to 40dBm at 1,5µm) or 3U 19" (up to 43dBm at 1µm), you will necessary find the product that you need for your application.
|
|
|
Glass fi bre optic cables are used for narrow spaces at extreme temperatures. Thanks to their small casing design, plastic fi bre-optic cables can be used in even the narrowest spaces.
|
|
FEATURES & BENEFITS
* Operating band in C,L-bands
* High power and high reliability
* Low noise figure
* Bench top type amplifier module for R&D
* Custom-designed gain-brock
APPLICATIONS
* DWDM transmission systems
* Testing of Optical systems
|
|
RiKO FZ1 Fiber Amplifier
Qualified Sensors From Taiwan RiKO
FZ1 Fiber Amplifier. Small size, 10mm thickness, can be mounted in a small space. Several sensors can be mounted side by side. 20-TURNS TRIMMER. The optimum sensitivity can be set easily. Off-delay timer adjustable for 0ms, 40ms and 400ms.
Custom design is welcome.
We have updated our new catalogues on our website.
|
|
FL 20 R-PSM3
Miniature line
Teach-in by push of a button/control line
Contamination indicator
Red light 660 nm
N.O./N.C. selectable
For fibre optics diamter 2.2 mm
Key lock function
Also available with 4-pin connector
|
|
general data actual range Sb (FSE 200C1002) 160 mm
sensing distance Tw (FUE 200C1003) 45 mm
light source pulsed red LED
light indicator LED yellow
alignment / soiled lens indicator flashing light indicator
adjustment Pot 270°
wave length 660 nm
suppression of reciprocal influence yes
electrical data response time / release time < 1 ms
voltage supply range +Vs 10 ... 30 VDC
current consumption max. 30 mA
current consumption typ. 20 mA
voltage drop Vd < 1,8 VDC
output function light / dark operate
output current < 100 mA
short circuit protection yes
reverse polarity protection yes
mechanical data width / diameter 10,4 mm
height / length 27 mm
depth 14 mm
type rectangular
housing material plastic (ASA)
ambient conditions operating temperature -25 ... +55 °C
protection class IP 40
|
|
general data version fast version
actual range Sb (FSE 200C1002) 140 mm
sensing distance Tw (FUE 200C1003) 40 mm
light source pulsed red LED
light indicator LED green
alignment / soiled lens indicator LED green, flashing
output indicator LED yellow
adjustment Teach-in
wave length 660 nm
electrical data response time / release time < 0,05 ms
voltage supply range +Vs 10 ... 30 VDC
current consumption max. 45 mA
current consumption typ. 40 mA
voltage drop Vd < 1,8 VDC
output function light / dark operate switchable
output circuit PNP
output current < 100 mA
short circuit protection yes
reverse polarity protection yes
mechanical data width / diameter 12 mm
height / length 33,2 mm
depth 60 mm
type rectangular
housing material PBT / PC
connection types connector M8, 4 pin
ambient conditions operating temperature -25 ... +55 °C
protection class IP 65
|
|
|
|
|
|
Special features
Easy, intuitive adjustment
Bright 2x 4 digit display
Version with M8-connector
Integrated lock functions
Version with external teach-in and integrated teach-in feedback
The newest Series 67 line of fiber optic sensors is attracting much attention thanks to its simple, intuitive operator interface. Simply pressing the teach-in key twice allows two different objects or contrasts to be "learned" by the sensor. The bright, 2x4 digit display simultaneously shows the taught switching point as well as the relative receiving light level. Just like a potentiometer, the switching point can be changed at any time by using the +/- key. Two different security features protect the sensor against unintentional manipulation during ongoing operation: One is a complete lock, while the other option only allows access to the teach-in and manual switching point adjustment, while locking out all other adjustments such as light/dark operation, timer functions or the operating mode with defined response time. The new fiber optic sensor also boasts a wide variety of application possibilities. With a response time of only 50 microseconds it is among the fastest fiber optic sensors available on the market and therefore lends itself to high-speed processes. The integrated 12-bit A/D converter provides high resolution even in large ranges up to 4 m.
|
|
Main Features & Applications:
- 1529-1563 nm Bandwidth
- Fast Transient Gain Control Up to 12 dB
- Up to 12dB Mid-Stage Loss budget
- Compact Package
- Variable Gain
- Excellent Flatness APC, AGC, ACC modes
- For: Long-Haul and Ultra Long-Haul Applications
|
|
The polarization maintaining (PM) single polarization EDFA is made for applications where the signal has to be amplified to overcome insertion losses of PM components like amplitude and phase modulators or other PM photonic devices. The PM EDFA features single polarization input and output isolators to assure high polarization extinction ratio and stable polarization of the amplified output.
Key features and advantages
-Single polarization PM output
-High polarization extinction ratio
-Single polarization input and output isolators
-Stable output polarization
-Low noise figure
-High saturated output power
-High power stability
-Integrated control electronics
-Robust OEM enclosure with integrated heat sink
-Benchtop instrument version available on request
|
|
The Erbium–doped Fiber Amplifier (EDFA–C band) is a general–purpose optical amplifier for the C band. This single pump optical amplifier features over 17 dBm of saturated optical output power, together with a high small–signal gain and low noise figure. A benchtop instrument version is also available on request.
-Key features and advantages
-High saturated output power
-High power stability
-Integrated control electronics
-Robust OEM enclosure with integrated heat sink
-Choice of connector type
-Custom specifications on request
-Benchtop instrument version available on request
|
|
The Erbium–doped Fiber Amplifier (EDFA–C band) is a general–purpose optical amplifier for the C band. This single pump optical amplifier features over +17 dBm of saturated optical output power, together with a high small–signal gain and low noise figure. Several front panel analog control options are available, including variable output power control and variable pump current control. A built-in power coupler with front panel connector is also available as an option. An OEM module version is also available on request.
Key features and advantages
-High saturated output power
-High power stability
-Integrated control electronics
-Choice of connector type
-Custom specifications on request
-OEM module version available on request
|
|
The Ytterbium–doped Fiber Amplifier (YBFA–PM) is a general purpose polarization maintaining single polarization optical amplifier for the wavelength region 1030 nm–1070 nm. The amplifier is a dual stage PM Ytterbium–doped Fiber Amplifier. Performance is optimized for 1064 nm at maximum setting of each pump laser diode. This double pump optical amplifier features over +16 dBm of saturated optical output power, together with a high small–signal gain and low noise figure. Several front panel analog control options are available, including variable pump current control for each pump diode (shown in picture above). An OEM module version is also available on request.
Key features and advantages
-Single polarization PM output
-High polarization extinction ratio
-Stable output polarization
-Low noise figure
-High saturated output power
-High power stability
-Integrated control electronics
-Custom specifications on request
-OEM module version available on request
|
|
|
The EFA-series of benchtop EDFAs are repackagedversions of the high-performance optical amplifiers found in MPB's repeaterless-link telecom equipment. These wall-plug units include preamplifiers with high gain and near-quantum-limited noise figure, as well as power amplifier models with saturated output powers up to 23 dBm.
|
|
The Manlight High Power Amplifier for CATV and FTTx applications
offers a cost effective solution in bringing the bandwidth closer to the end users. With a unique design based on Manlights in-house pump combiner and optical know-how, the high power amplifiers are optimized to offer high power and low noise figure with proven reliability and quality. The output power can be distributed
between 1 to 16 output ports.
The use of efficient and reliable uncooled pump diodes allows the Manlight amplifiers to reach high output powers with low overall power consumption. The control electronics featuring alarms, automatic
shutdown, and RS-232 communication interface is driven by a 5 / 24 VDC power supply.
|
|
BaySpec's IntelliGain® and IntelliSense® Erbium-doped Fiber Amplifiers (EDFA) are designed and manufactured in the U.S.A. to meet stringent Telcordia GR-1312 requirements for reliability and performance.
A compete line of EDFA gain modules are available, designed to meet various amplification requirements for single-channel, narrowband, and DWDM transmission in metro, long-haul and ultra long-haul networks.
Features:
- Output power from 10 to 26 dBm
- Fast transient response
- Gain flatness
- Very low noise figure
- Variable gain
- Mid-stage access
- Selection of industry standard packages
- Ultra low power consumption
|
|
|
|
|
|
Meech Air Technology High Thrust Jets are designed to provide a high power blast of air whilst reducing compressor demand and lowering noise levels. The High Thrust Jets use a very small amount of compressed air to generate a high power blow off force. This is achieved by forcing compressed air through an adjustable internal circular slot. The high velocity air from the slot generates an area of low pressure at the rear of the jet that entrains ambient air at a ratio of 4:1. This maximises the high power blow off.
Meech Air Technology Energy Saving Air Amplifiers provide large airflows whilst only consuming a minimal volume of compressed air. A tiny amount of compressed air is released through an adjustable circular slot inside the Air Amplifier creating a 'tube' of air. The 'tube' of air then travels towards the front creating areas of low pressure behind and in front that entrains ambient air at a ratio of 12, 20 and 25:1 depending on the size of air amplifier. Meech Air Amplifiers are available in three sizes in Stainless Steel or Aluminium to suit a wide range of applications.
|
|
Adjustable Air Amplifier - Nex Flow™:
- Adjustable Air Amplifier from Nex Flow™ is used for a variety of applications - either coated aluminum or stainless steel for high temperature and corrosive environments.
- Adjustable Air Amplifier is easy to mount and maintain. Compressed air consumption and noise levels are reduced.
- Adjustable Air Amplifier takes energy from a small volume of compressed air to produce high velocity, high volume, low pressure output airflow.
- Adjustable Air Amplifier is quiet, efficient and can amplify flows up to 20 times their input air consumption rate.
Specifications:
Stainless steel or coated aluminum are materials of construction. Three standard outlet (outside) diameters: 1-1/4" (31mm), 2" (51mm), 4" (200mm). Other sizes available upon request.
Come with a standard .002" (.05mm) gap that is adjustable. If greater force is required, the gap may be adjusted for greater flow.
|
|
Streamtek's Adjustable Air Amplifiers are a simple, low cost way to move, smoke, fumes, air, and light materials. Using a small amount of compressed air as their power source, our Adjustable Air Amplifiers pull in large volumes of air from the surrounding environment to produce high velocity, high volume outlet flows. Quiet, efficient Air Amplifiers will create output flow sup to 30 times their consumption rate.
ADVANTAGES OF AIR AMPLIFIERS
- Easy to mount and maintain.
- Instant ON/OFF with no moving parts, no electricity or explosion hazard.
- Adjustable output without tools or shims
- Quiet Operation
- Compressed air operated
> > > > (SPECIFICATIONS)
Stainless steel or aluminum are materials of construction. Four standard outlet (outside) diameters: 1-1/4" (31mm), 2" (51mm), 2-1/2" (64mm), 4" (200mm). Other sizes available upon request.
|
|
|
|
|
|
HAA31 Models
Single-acting, single-stage air pressure amplifiers
3 models with ratios of (2.5:1), (3.5:1) & (4.5:1)
Maximum inlet pressure of 125 psi
Maximum outlet pressures from 320 psi to 600 psi
AA Models
Single-acting, single-stage air pressure amplifiers
3 models with ratios of (8:1), (15:1) & (30:1)
Maximum inlet pressures from 1,250 psi to 4,500 psi
Maximum outlet pressures from 2,500 psi to 4,500 psi
AAD Models
Double-acting, single-stage air pressure amplifier provides outlet flow on each stroke of cycle and gains "lift" from inlet pressure
4 models with ratios of (2:1), (5:1), (15:1) & (30:1)
Maximum inlet pressures from 300 psi to 4,500 psi
Maximum outlet pressures from 300 psi to 5,000 psi
AAT Models
Two-stage air pressure amplifier provides two high pressure pistons of different ratios within a single unit for maximum efficiency at higher outlet pressures
3 models with ratios of (7/30), (15/30) & (30/50)
Maximum inlet pressures from 300 psi to 3,000 psi
Maximum outlet pressures from 4,500 psi to 5,000 psi
|
|
FEATURES - BENEFITS - APPLICATIONS
- Compact: installs off the floor, out of the way, in any position.
- 2 connections: plant air in, amplified air out. (Pilot air connection is ptional for start-stop control with a PCV valve or solenoid valve and pressure switch).
- Can replace a dedicated air compressor: 10 HP size in a typical large plant spot requirement for 100 PSI when only 80 PSI is available. (Model 5A-DS-2)
- Replace bottled nitrogen: up to 700 PSI for air testing, lab or production. (Model 5A-DS-5)
TYPICAL APPLICATIONS FOR HIGHER AIR PRESSURE
- Valve actuators
- Air starters
- Bin vibrators
- Pneumatic drill motors
- Air clamps
- Air brakes
- Off road tires
- Pneumatic nailers,staplers, straping machines
- Air/oil hoists
- Air presses
|
|
|
ITW Vortec’s Round Transvectors use a small amount of filtered compressed air to deliver a large airflow for a wide range of conveying, ventilation, drying and cooling applications. The high-flow, bladeless blowers don’t require machine guards and are especially useful for removing plastic scrap and metal chips, ventilating fumes or smoke, and conveying small parts, pellets, powders and dust. As a vacuum or blowoff device, these air amplifiers are more compact and less expensive than variable-speed blowers and fans, provide instant on/off performance, and operate at low noise levels to meet OSHA requirements. Round Transvectors are easily mounted and, with no moving parts to wear out or break, are virtually maintenance-free. Used in ducted and unducted applications, Round Transvectors are available in several sizes, in both aluminum and stainless steel, and can deliver flow rates from 32 to 2300 SCFM.
|
|
|
Air amplifier is easy to mount and maintain reducing both compressed air consumption and noise levels. It takes energy from a small volume of compressed air to produce a high velocity, high volume, low pressure output air flow.
|
|
|
Air driven amplifiers are used to bring shopair pressure to a higher level. Compression ratios of 1:2, 1:4 or even higher are possible. Amplifiers can be built as a system or with a reservoir. Applications are increasing cylinderforce, pressurising shopair locally and saving the lifetime of your compressor by reducing your maximum pressure.
|
|
MAXIMATOR PLV series air amplifiers are suitable for the compression of pressurised air or nitrogen. The units are capable of increasing normal pressures of 4 bar or 6 bar to the desired final pressures. The PLV Air Amplifiers are operated with normal shop air and are provided with a variety of amplification ratios.
All PLV Air Amplifiers can be supplied with an air control unit comprising a filter, pressure regulator with pressure gauge and an air shut-off valve. The desired operating pressure can be preset by means of the air control unit in correspondence with the different pressure ratios. We can offer you a choice between a standard PLV Air Amplifier Station or a customised solution.
|
|
A simple, low cost way to move air, smoke, fumes, and light materials.
Air Amplifiers utilize the coanda effect, a basic principle of fluidics,
to create air motion in their surroundings. Using a small amount of compressed air as their power source, Air Amplifiers pull in large volumes of surrounding air to produce high volume, high velocity outlet flows. Quiet, efficient Air Amplifiers will create output flows up to 25 times their consumption rate.
|
|
The Diaphragm Amplifier is a miniature interface device that performs the same function as a piloted 3-way valve, but with low outlet flow rates. Pneumatic signals of several inches water gauge applied to the input will control an output pressure of up to 35 PSI in both digital and analog systems. They can be used at fluidic signal levels for providing isolation and in timing circuits.
Five models are available, providing a variety of actuating pressures for the valve. Maximum supply pressure is 25 to 35 PSI depending on the size of the supply orifice.
|
|
SERIES MF
Alfamatic pressure intensifier series MF is a unit consisting of a pneumatic cylinder and a high pressure chamber.
* Working without lubrication
* Possibility to turn fluid connections around 360 degrees
* End stroke deceleration
|
|
Features
* Flow capacity of 45 SCFM (76.5 m3/HR)
* Ten available pressure ratios
* Optional Adjustable By-Pass Needle Valve option includes bubble tight exhaust valve.
* Optional Fixed Negative Bias.
* A separate Control Chamber isolates the diaphragm from the main flow.
* Unit construction.
* Mounting Bracket available
* Canadian Registration Number (CRN) Certification.
|
|
|
Energy Saving Safety Blowguns from Meech combine an ergonomic lightweight gun handle with the Meech Air Saver Nozzle. The innovative nozzle design forces compressed air through an adjustable circular slot and then directs it at high velocity over the outside of the nozzle cone. The design amplifies the output airflow by entraining the ambient air at a 25:1 ratio. Meech blowguns typically save up to 70% of compressed air usage compared to conventional types of blowgun whilst dramatically reducing noise levels.
|
|
|
|
see the results for the following category : 
