|
|
Rosedale High Efficiency Filter Bags
Our HI-E series of bag filters meets the most stringent needs for fine process, hydraulic fluid, and lubricant filtration. All are made of unique microfiber materials, designed to increase the efficiency and dirt-holding capacities of these bags.
Microfiber Material Construction
Polyester or polypropylene microfibers and standard fibers are variably calendered to produce a single layer of microfiber material. Our unique construction can provide filtration to a 1 micron rating. Polyester microfiber material should be used where oil adsorption is not desirable or where higher temperatures are required.
Filtration Level
These bags have been tested by an independent laboratory to determine the filtration efficiency and dirt holding capabilities for each. They have been manufactured so that the efficiencies for both polyester and polypropylene are identical.
|
|
These cartridge-filter housings are rugged and low in cost. They hold five cartridges, in 10-inch, 20-inch, 30-inch, or 40-inch lengths, using industry standard designs (222, SOE, or DOE). The unique, “quick-opening” clamp design uses a standard gasket.
Standard Features
- Low pressure drop
- Permanently piped housings are opened without disturbing the piping or requiring tools
- Quick-opening, clamp-type cover
- Carbon or stainless steel housings
- Adjustable-height tripod legs
- Holds 5 cartridge elements
- Accommodates cartridge elements in four lengths: 10”, 20”, 30”, 40”
- 125-psi rated housing
- 3/4-inch clean-dirty/gage ports
- 2-inch female NPT ports
- V posts or threaded-center posts
- Standard hardware V-post and spring seals are 316 stainless steel.
- O-ring seals: Buna N, EPR, Viton®
|
|
|
GS Series Polyethersulfone Membrane Cartridges are designed for general industrial service where the need for cost effective filtration is a must. These cartridges utilize a pleated membrane design, incorporating the maximum amount of media that can be used in a cartridge. These units, manufactured for general industrial use, are manufactured to the same high standards as our special application cartridges. Pore sizes start at 0.03 µm with a polyethersulfone membrane.
|
|
Liquid Filters
AMERICAN FABRIC FILTER CO. provides a complete range custom manufactured liquid filter bags for all standard and most custom vessels in plain or glazed felts from ½ to 100 micron and mesh from 5 to 800 micron.
Construction options include plastic, carbon, stainless and PVC-coated steel rings; handles, draw strings and muslin or mesh (multi-layer) covers.
All filters are custom manufactured to meet your requirements. Please have the filter style designation or measure the length, flat width of the bag and ring diameter (if used when requesting a quote. For unusual or difficult to measure applications, a sample bag that you know fits is most desirable.
|
|
|
AAF AmerKleen filter cartridges are protected at all times by an all metal, filter housing. The AmerKleen housing is equipped with an anti-surge assembly consisting of a wire form attached to the back of each sealing frame. By holding the cartridge firmly in place, the housing protects it against turbo-surge. The AmerKleen cartridge is designed to be changed at the normal 90-day maintenance cycle, with an adequate safety margin should the locomotive encounter delays in servicing. When the time comes, installation is a fast and easy process. By the simple removal of two bolts and a sealing frame, the AmerKleen cartridge is front-loaded. Replacing the sealing frame automatically forms an air-tight seal. Normal air flow through the filter insures that all seals remain tight without the need for time-consuming alignment.
|
|
High efficiency terminal filters for highest requirements for air purity and hygiene.
High efficiency terminal filters are used as final filters in areas with the highest requirements for air purity and hygiene such as in the medical, biological and pharmaceutical industries as well as in other sensitive areas.
Both HEPA and ULPA filters can be used.
These filters can be combined with different ceiling diffusers from the TROX standard product range.
- Particulate air filter ceiling diffuser
- Main filter for high air purits and sterility
- Ceiling diffusers are a comfortable way to generate mixed air flow quietly,
even for large quantities of air.
|
|
1. Element diameter is 63.5 mm with cover.
2. Pressure drop calculations based on 20 micron elements.
3. Element length is for mesh pack and does not include end fitting.
4. Polymer viscosity is 250 Pas (2500 Poise).
5. Design conditions are 241.5 Bar (3500 psi) and 343.5C (650F).
6. Vessel material is 304SS and system is designed per ASME Code.
7. System configuration is MPST's patented close-coupled design.
8. System includes manual vent valves and hydraulically automated diverter valves with control panel.
9. System prices are Ex Works Maag Factory.
|
|
|
|
|
|
Polymer candles
Polymer candles are the choice of the processor when it is important to have the lowest capital cost combined with ease of replacement, lower downtimes and overheads. Candles are available in pleated stainless steel fibre (e.g. for PET film, fibre and resin) or cylindrical woven meshes (e.g. for BOPP film) utilising stainless or speciality steels. Our designs encompass the fully welded, REMPAKTM and re-coverable versions, with the last two options representing a lower cost product where the valuable hardware can be reused when the media has reached the end of its life.
Our candles are available in industry standard designs, or can be custom designed to fit any particular housing. With high strength, they are available in filtration ratings from 3-100 microns, and would normally be supplied with an outer guard both to protect the media. Our range of high strength, highly permeable steel stainless fibre media gives candles with low initial pressure drops and long on- stream life.
Our candles are readily cleanable with current technology and we would be happy to advise on appropriate cleaning methods available.
|
|
CPD pleated polypropylene depth cartridges are designed for clarifying applications requiring high flow capacity. The depth media utilized in the CPD product line is high loft Melt-blown polypropylene which gives exceptional flow characteristics and high dirt holding capacity because of its high internal porosity. Fine polypropylene fibers are bonded together to ensure no fiber release in a fiber matrix that maintains high porosity. Rated at 99.9% efficiencies make it a cost effective filter designed to extend final filter life.
|
|
|
|
|
|
The reliability and efficiency of any filtration system is chiefly dependent on the quality of the cartridges used in it. Our full line of quality HILCO cartridges includes various sizes, filtration efficiencies and dirt-holding capacities for virtually every application. HILCO can restore many oils and coolants to a like-new condition.
All cartridges are developed to provide long service life and high quality. Many different media are specially selected, formulated and fine tuned on a regular basis to provide the most effective combination of fluid compatibility, particle-separation efficiency, low pressure drop and structural properties.
Controlled radius pleats are designed to maximize filtration area and dirt-holding capacity while resisting pinching, distortion and rupture. Gasket materials and adhesives are selected based on their compatibility with fluids and operating temperatures of each application. Cartridges feature rugged, fiberglass filled nylon and plated steel centertubes which resist collapse at high pressure differentials.
Fuel gas, process gas, seal gas, H2O injection, and transformer oil applications can also be accommodated by HILCO. We also make HILCO-quality replacements for other brands of cartridges used in lube oil and fuel oil applications.
|
|
Claris® Series Filter Cartridges
High Consistency Polypropylene Melt Blown Cartridge
Graded Pore Structure Enhances Dirt Holding Capacity
E-core, an Extruded Fibrous Core, Provides Excellent Strength
Unique Proprietary Process
Easy and Safe Cartridge Incineration and Disposal
All Polypropylene Construction
Free of Surfactants, Binders, and Adhesives
NSF Certified
Plastic and Metal Spring Assembly End Configurations Available
Performance Specifications
Filter Grades:
1, 3, 5, 10, 20, 30, 50, 75 µm
Maximum Differential Pressure:
50 psid (3.45 bar) @ ambient
25 psid (1.72 bar) @ 140°F (60°C)
Recommended Change Out Differential Pressure1:
35 psid (2.4 bar)
Purity:
Claris Series filter cartridges are free of surfactants,
anti-static agents, binders, and adhesives.
|
|
|
General grade membrane cartridges are designed for general purpose use wherever a cost effective membrane filter is required and is offered in polyethersulfone, nylon, Teflon, and polypropylene. Designed to hold the maximum amount of filter media that can be completely and effectively utilized in a cartridge, General grade membrane filters lower the cost of filtration . Membrane cartridges are flushed with 17+ megohm-cm water to remove potential extraneous manufacturing debris. These cartridge modules are also individually tested. Priced below special purpose cartridges, General grade membrane cartridges are still manufactured with the same careful attention to both quality and performance.
|
|
|
|
|
|
3-inch and 4-inch diameter modules available in 10-foot and 12-foot lengths.
The use of KMS SUPER-COR® membranes for juice processing eliminates the need for pretreatment and associated handling equipment-no more centrifuges, screens, rotary drums, diatomaceous earth, or fining agents. It also does away with the maintenance associated with pretreatment processes, saving you time and money. The latest SUPER-COR® modules have a robust backing structure that supports the extended processing requirements of today's juice processing plants.
SUPER-COR®, designed around the needs of juice processors worldwide:
• Higher product yield
• No preprocessing required-eliminates diatomaceous earth and fining agents
along with their associated maintenance and disposal costs.
• Transparent module housing for ease of inspection
• Long membrane life
SUPER-COR® Systems, combined with last stage of SUPER-G® modules, clarify juices at extremely high yield rates. Up to 98% yield can be achieved without adding diafiltration water.
|
|
Biofil PES
Incorporating a hydrophilic membrane, the Biofil cartridge has a unique mirrored asymmetric structure which gives the media added strength and very low clean pressure drops. This helps to ensure that cartridge integrity is maintained when repeatedly steam sterilised. The characteristics of the membrane also results in excellent resistance to hydrolysis, along with low protein binding and colour stripping. Furthermore Biofil PES cartridges have excellent chemical compatibility across the full range of pH values.
Biofil PES cartridges have been validated and are ideal for applications ranging from the production of beverages to the filtration of blood and serum. They compare favourably in many applications with alternative cartridges manufactured using Nylon, Cellulose and PVDF.
|
|
TARGA® industrial water cartridges provide compact pretreatment for ultrapure water systems.
8-inch TARGA® cartridge
TARGA® industrial water ultrafiltration cartridges are produced for general water treatment applications. They are particularly effective for pretreatment to reverse osmosis membranes.
• pH Tolerant
• Chlorine Resistant up to 200 PPM at 10.5 pH
• Temperature range of 32 degrees - 104 degrees F
8-inch diameter cartridges are available in two lengths: 48-inches and 72-inches.
TARGA® cartridges have a broad range of applications, including:
• Carbonated Soft Drinks and Bottled Water
• Boiler Make-up Water
• Microelectronics
• Pharmaceuticals
|
|
CIH multi cartridge V-band clamp closure housings are a proven design suited for commercial and industrial applications. Offered in 4,5,7,12,and 21 round configurations and in 304 SS or 316L SS. All CIH housings are designed with Universal cartridge cups, allowing you to use DOE style cartridges or 222 SOE cartridges with fin or flat end. This gives you one housing that can meet your nominal and absolute filter needs and provides quick cartridge change outs. Housing is standard with EP gasket and also offered in other materials and port sizes, allowing the CIH to meet a wide spectrum of applications. Every housing is supplied with a mounting kit and operations manual.
|
|
The Hilco TurboFlo Duplex Filter line is easy to operate and maintain with a low turning torque and no jacking of the sealing pads. Welded-in transfer valves and high flow synthetic elements save space, and flow is under the filter cartridge which does not impinge on the filter elements. With no flanges between the transfer valve and filter housing, there are fewer potential leak points.
Features includes:
• ASME Code construction
• O-ring sealed covers
• Coreless elements
• Standard carbon steel and 316 stainless steel
The TurboFlo Duplex Filter is also available in 1-1/2” to 8” inlet and outlet connections for flows up to 2000 gpm and pressures up to 5000 psi.
For complete product information, request bulletins TBF-2 and TEB-2.
Other Filter Housing products include:
• Integral Duplex Filters
• Standard Housings for High Flow Synthetic Elements
• Standard Non-Code Housings
• Bag Filter Housings
• Seal Gas Duplex Filter Housings
|
|
FM4X1-1: 4-round 10 in. Cartridges, 1 in. NPT; 25 gpm max; (Legs Optional)
Description:
100% stainless steel design, V-band clamp lid closure, pressure rating 150psi. Available in 304 or 316ss.
|
|
|
|
|
|
CCL Series Housings
Pall CCL Series Housings accept Pall 1000 style filter elements in a 10, 20 or 30 inch length, or Pall 21/2%u2033 diameter UNI CAP style pleated filter elements. This series of housings is typically used for flow rates of 15, 20 and 25 GPM for the 10, 20 and 30 inch cartridges respectively. The housings are constructed of a 316 stainless steel investment casting head and a 316L stainless steel bowl. One or two polypropylene couplers, to join 10%u2033 1000 style filters together, are included for 20 and 30 inch housings, respectively. Inlet/outlet connections are 1%u2033 NPT or 1%u2033 flange. The head and bowl of the housing are fastened with a quick opening stainless steel Tee handle V-band clamp. Head to bowl sealing is by standard 242 O-ring.
Specifications
Design Ratings:
Pressure: 200 PSIG (1379 KPA)
Temperature: Limitations due to O-ring material.
Buna N: -20°F to 250°F (-29°C to 121°C)
Viton A*: -20°F to 400°F (-29°C to 204°C)
Ethylene Propylene: -20°F to 300°F
(-29°C to 148°C)
A bowl drain connection, as well as 2 pressure taps in the head are standard on all models.
The housings may be mounted in any position except for oil mist removal from compressed gases, where it must be mounted vertically with the bowl down.
|
|
|
CSH sanitary cartridge housings, available in 1,3,6,8,12 and 21 round models with swing bolt and clamp closures are a proven design suited for high purity beverage, chemical and pharmaceutical applications. They are manufactured in 316/316L Stainless Steel with a 25 RA internal finish. All CSH housings are standard with 2-226 style cartridge adaptors with removable tube sheet, giving you a positive locking tab seal. This allows flexibility in one housing to use different cartridge lengths and maximize filter performance and cost. CSH housings have no internal threaded parts that come in contact with the process fluid and are standard with food grade silicone gaskets. 1” sanitary gauge port tops with 1/2” sanitary vent and drain ferrules are standard features.
|
|
Sanitary grade housings
Designed for the demands of critical applications particularly in the pharmaceutical, microelectronics and food and beverage industries, our sanitary grade housings have easy to use closures with a crevice free construction. The internal surfaces are resistant to bacterial accumulation and are easily steam sterilised or chemically sanitised. Microbial security can only be guaranteed with this grade of housing.
|
|
CHR single cartridge ring closure housings are a proven design suited for commercial and industrial applications. Available in 304 SS, 316 SS or Brass head with 304 SS sump. The CHR housings are rated for 300 psi and are designed for DOE style cartridges with machined knife edge seal surfaces for a no-bypass seal. All sump seals are spring loaded allowing you a variety of cartridge lengths and providing quick cartridge change outs. With the complete range of O-ring materials and port sizes the CHR will meet a wide spectrum of applications. Every housing is supplied with a mounting kit and sump rod.
|
|
EPS cartridges are designed to meet the special needs of the electronics and high purity chemical industries. Polyethersulfone membrane cartridges are resistant to most acids and bases and capable of handling strong sanitization agents. High flow rates make Polyethersulfone a good choice for central DI water systems. This membrane will also handle elevated process temperatures in compatible fluids. To minimize extractables, each cartridge module is pulse, power flushed until the rinse effluent reaches 17+ Megohm-cm and less than 3 ppb TOC. Each cartridge module is also individually tested.
|
|
With nearly 1000 systems installed, KMS pioneered the use of membranes in the wine industry. We have learned that each wine is unique and the filtration required must match the wine itself. We work with winemakers to enhance the organoleptic and aesthetic characteristics of the final product.
KMS' one step process reduces processing costs
Membrane systems using crossflow filtration with the durable KMS WINEFILTER cartridge offer excellent throughput rates eliminating use and disposal of diatomaceous earth or filter sheets in a compact system design.
• Gentle process promotes outstanding product quality and color intensity
• Back pulse/throttle permeate allows steady productivity
• Eliminates the need for diatomaceous earth (no disposal or filter aid costs)
• No pretreatment, fining agents or filter sheets
• Standard designs available
|
|
Take advantage of the KMS proven track record
For more than thirty years, the highly innovative FLUID SYSTEMS® brand of Koch Membrane Systems has been serving the residential and commercial water filtration and purification markets with state-of-the-art membrane elements.
|
|
SC series cartridges have been designed to tackle the toughest of filtering applications. The cartridges are available in 304 or 316 Stainless steel with a complete option of end cap configurations. You can choose the pleated style for extra surface area and extended life or the cylindrical for easy cleaning. SC cartridges are the perfect choice for high temperature, high pressure, and resolve chemical compatibility with polymer elements. SC filters are cleanable and reusable and offered in retention ratings as low as 2 micron through 840 micron.
|
|
Self cleaning filters are available in either manual or automatic versions with standard design options for either low pressure (14 BARG) or high pressure (35 BARG) system.
In operation the liquid enters the body and flows through the element from outside to inside.
Debris is collected on the outside of the wedge wire element, which is cleaned without flow interruption by rotating the cylindrical element against twin scraper blades.
The debris accumulated during element rotation is deposited into the bottom of the filter body from where it is periodically discharged, manually or automatically.
|
|
Filter cartridges
2fi manufacture a range of industry standard stainless steel filter cartridges suitable for use in a wide range of industries, including pharmaceutical, chemical process and petrochemical, at extreme conditions of temperature and pressure.
Wholly constructed of grade 316L stainless steel, in fibre, powder or mesh media, the cartridges are available plain or pleated with a choice of end fittings.
|
|
|
|
|
|
|
EUROFILTRAZIONE is a leading company in the production of filter elements for industrial applications, and produces a complete range of filter cartridges for EDM machines, of both edge and plunge type. The use of filtering materials specifically conceived for this purpose, ensures the best possible results. EUROFILTRAZIONE filter cartridges are in fact top of the range both in relation to national and foreign production output. The winning features of these cartridges being a high filtering capacity with low charge loss, and considerable storage capacity in even the most severe operating conditions, thereby ensuring the long working life of the product. Thanks to these features, and highly competitive price levels, it possible to greatly reduce filtering and electro-erosion costs without in any way jeopardizing performance levels. EUROFILTRAZIONE is therefore a truly top-level manufacturer, capable of meeting customer requirements both with a range of standard products as well as with special products, suitable to face specific challenges.
|
|
 see the results for the following category : EMI filters |
|
|
