|
|
Hörmann fire protection, because it's good to be on the safe side!
When you purchase a Hörmann Fire Door you are assured quality, protection and safety for decades! Take advantage of our fire doors to meet the special requirements of your application in the non-domestic building sector.
Reliable fire protection calls adequate new developments in each and every detail. This is where our qualified development teams demonstrate their competence, time and expertise.
Hörmann invests in morden production technology in highly-specialized factories. Computer-controlled processing guarantees precision cutting and the perfect fit of all hardware and functional components. This is the prerequisite for customized solutions in the non-domestic building sector.
Expert advice and professional installation guarantee a perfect result in every respect.
|
|
The fire-rated sliding door as an escape way
In the event of a fire alarm, the optional escape way function allows using the door in the same manner as a manual swing door.
|
|
|
Doors of great robustness, adapting to the needs of protection against fires as much for people as of objects, Constructed according to effective norm.
|
|
DICTATOR provides complete hold open systems for hazardous areas
They comprise explosion-proof smoke and heat detectors, door operators and the electromagnets. They comply with the requirements for group II products and can be installed in all zone 1 and 2 areas (according to VDE 0165). The explosion proof magnets are encapsulated (EEX m). Two series are available: with ex-proof connection box or with connection cable. The standard length of the cable is 2 m, but it can be delivered in the length required on site. The holding force of the magnets is either 550 N or 145N. The integrated release pin eliminates any remanence after switching off the power supply of the magnets, ensuring that the magnets always releases the door. All ex-proof magnets are equipped with diodes and polarity protection.
The DICTATOR ex-proof magnets have been tested both according to EN 1155:2005 for hold-open systems and the ATEX directive by the Physikalisch-Technische Bundesanstalt Braunschweig (certificates PTB 03 ATEX 2174 X and PTB 03 ATEX N060).
In addition to the ex-proof magnets DICTATOR also provides a large range of electromagnets for hold-open systems, that comply with the EN 1155:2005 and are approved for the use in hold-open systems.
|
|
Doorholder magnets, explosion proof
Doorholder magnets with 650 N, 1300 N and 2000 N force, explosionproof, in acc. with ATEX 94/9/EC, II2G EEx m II T6, II2D IP66 T85, for use in hazardous areas zone 1, 2, 21 and 22 for all kind of gas, mixtures, vapours and dust (in acc. to type). Protection class IP65.
|
|
|
In order to guarantee effective workflows for our customers we focus on customer specific solutions when it comes to insertion and maintenance access. Therefore the HGB GmbH has developed a variation range of multi-winged sliding and wing doors, flap fields and pendulum flaps, which are fitted according to any application need, in order to meet our customer’s production flow ideally.
|
|
|
Numerous versatile options, functions, control extensions and interfaces are provided to integrate the doors into a building's master control system. A multitude of choices with regard to available materials, possible shapes and conceptions offer the planner virtually unlimited design possibilities. The architect particularly appreciates the Kaba door automation equipment that enables him to realize even his most extravagant ideas.
|
|
DEVICE ANTI-PINCE FINGERS OF THE INDUSTRIAL DOORS
GAROMIN®
In the professional buildings the doors increasingly tighter, heavier, are sometimes equipped with a system of assisted closing (obligatory for the doors firebreak). If these measurements prove to be effective against the heat or the drafts, the consequences in the event of pinching can be extremely serious, going until the loss of whole or part of one or more fingers. In addition to the pain and the handicap, these accidents very often have important financial repercussions for the victim, which can lose a big part of its resources, and for the company which loses work hours, without forgetting premiums of insurance to the rise.
The device anti-grip Garomin® fingers effectively protects the unit from the personnel of such accidents. This clever system is integrated into all the buildings, of the laboratory to the workshops, without forgetting the administrative parts and the social buildings.
Composed of flexible bellows with 1,3,7 or 17 whorls which do not block the opening of opening (doors, windows, wall cupboards...), Garomin® is posed simply using aluminum profiles, on all the types of doors (90°, 180°, beating doors...) without modifying their intrinsic characteristics, in particular sealing or the capacity firebreak. In the event of intervention on opening, it is withdrawn and positioned back without difficulty. Realized out of flexible elastomer which can be recycled with 100%, Garomin® is in conformity with the standard ISO 14000. Anti-fungic, classified m2 with fire, it resists the acids, the detergents and the U.V. Garomin is available in 2 colors, yellow and black.
|
|
| ... products without technical information |
| |
The application needs in practice are so manifold like the bandwidth of the lift gates and lift fields from the HGB GmbH.
Within the different type series widths up to 9.000 mm and lift heights up to 6.000 mm can be realized. Hereby, we especially focus on the aspect of security. An electronic chain breakage monitoring, a connecting block along the closing edge, and a mechanical fall arrester of multiple supporting appliances according to the norm EN 12604 (Appendix B) serve as a safety device in context with the power operated lift gates and lift doors. A complete documentation self-evidently belongs to a complete project perimeter.
|
|
| ... products without technical information |
| |
Novaporte RP
Flat Inspection door. Steel. Stainless steel.
Natural rubber seal
Smooth convex outside cover without retention. 180° opening
Constant closing pressure by spring assembly
Double bottom, smooth convex inside without retention (DG version)
Fast opening and closing by toggle fastener with possibility of locking
Flat welding lugs
|
|
Novaporte RC
Rotatable inspection door with collar. Steel. Stainless steel
Natural rubber seal
Rotatable base with collar
Smooth convex outside cover without retention. 180° opening
Constant closing pressure by spring assembly
Double bottom, smooth convex inside without retention (DG version)
Fast opening and closing by toggle fastener with possibility of locking
Welding collar
Clamping collar
|
|
DICTATOR furnishes a large range of doorclosers and related products. It offers also solutions for a lot of special and demanding applications.
Special door closer solutions
DICTATOR provides two special doorclosers especially for gates in fencings of industry plants, kindergardes, play grounds etc. The RTS tube doorcloser is virtually invisible due to the fact that it is built into the door or the gate. The DIRECT doorcloser is installed on the door / gate.
Floor springs: the DICTATOR WAB floor spring is the ideal solution for large, heavy and highly frequented hinged doors up to 600 kg. The fact that the complete interior is filled with oil assures a troublefree damping and closing and a extremely long life.
Back check
The DICTATOR back check with hydraulic damping for hinged doors, slows down the opening movement of the door before it reaches the open position and limits the opening angle of the door. It prevents damage to the door by providing a cushioning effectat the required angle and reduces the danger of injuries and accidents to persons. The back checks are available with and without adjustment.
Closing springs
DICTATOR closing springs can be either built into the doors or installed on the door, recommended to be used n combination with a DICTATOR door damper.
Swing door hinges: the Hawgood swing door hinges are available for different door thickness. Their special feature: due to their construction they swing the door leaf out of the passage thus leaving the largest possible passage way.
|
|
Heavy duty safety gate switch
The ATSTOP has a heavy duty tongue and head where the tongue allows a 12mm misalignment. The tongue and head unit can rotate in 90o increments. The product is ideally designed for machines without run down cycles where quick and frequent access to equipment is required, via either hinged or sliding doors.
When the machinery is in operation the tongue is engaged and the power is on. If accesss is required, the door is simply opened releasing the tongue from the unit,giving positively guided, forced disconnection of the safety switch contacts.
- designed for use in harsh environments (dust, moisture and vibration)
- different control voltages available
- AS-interface version available
- available with different heads and actuators
- available with safety keys (to prevent accidental lock in of personnel)
- for use in category 4 (EN 954-1) applications
|
|
Mechanical robust door interlock for safety accesing machine areas, gates or hatches.
- Can be used in Category 4 (EN 954-1) applications
- Pattented runner bar system
- Safety key to prevent accidental lock in of personnel
- Available in full stainless steel
- Suitable for use in ATEX zone 1 and 2
- No wiring on the installation
Can be used in combination with Fortress (solenoid controlled) key switches and key exchange boxes.
|
|
| ... products without technical information |
| |
The thermal management program is a computer-aided calculation system for switch cabinet air-conditioning.
It takes care of all the worries associated with production standstill caused by overheated switchgear systems.
The program contains databases of the Eldon enclosures, their dimensions, the conditioning devices (filter/fans, cooling units, heat-exchangers) and a selection of the most used electrical components with their heat dissipation. Additional databases can be created within the program.
After having chosen the enclosure type and size, given all the environment conditions (enclosure situation, required equipment temperature, ambient temperature and heat dissipation), the program will propose the most appropriate conditioning solution. A calculation report can then be printed.
To allow the installation study of the cooling devices on the enclosures in the early stage of a project, dimensional drawings of all the devices will be provided in CAD system DXF and AutoCAD file formats soon. You can find the different dimensions in our datasheets.
Download our easy to use Calculation Model in www.eldon.com
|
|
SLIM-IN Line
Door/Wall mounting System description
Specifically developed for door or wall mounting, the air conditioners of the series SLIM-IN cover a cooling capacity range from 850W to 2500W.
They are available in 230V (and some items in 400V).
Common to most of the SLIM-IN models is the Maintenance Free concept.
All models are equipped with an electronic board (not for EVE08).
::Reciprocating hermetic compressor with thermal amperometric protection ::Ecological R134a refrigerant, CFC free ::Condensing and evaporating heat exchange coils in copper pipe with aluminium fins ::Internal and external fans on ball bearings with internal thermal protection ::Electronic board EBB (For EVE08 Internal mechanical thermostat set at 35°C, dead band 4°C) ::Power supply wire 3m long ::Steel sheet front cover powder painted RAL 7032 orange peel ::Zync plated frame
Optionals
::Stainless steel frame and front cover ::Not standard colour (RAL) ::Electronic board EBB (not available for EVE03)
|
|
All APEX air-conditioning units are HOMOLOGOUS for the motor industry and are recognised as being among the best performing, above all in harsh environment, such as workshops, factories, forges, foundries, blacksmith's and paint shops.
APEX condensers are specially designed and installed to operate WITHOUT FILTERING ambiant air. Their surfaces and installation are one of the key points in the overall performance of the entire APEX range.
We have developed a specific range of air-conditioning units for outdoor and marine applications. They are portable and/or suitable for operating in all weathers.
|
|
Air condensation can operate at temperatures up to 71 °C.
Air condensation technology can be used to air condition a cabinet when there is no industrial water supply.
Apex Technologies is the first to market a range of very high temperature air condensation air conditioners, specifically suited to extremely difficult industrial environments (foundries, forges, iron and stell market, thermal treatement, ovens, cranes...)
This technology is fully compatible with the features of other vertical air condensation air conditioners in our range: cutout, wiring, components, operation without air filters thanks to very wide blades, separation of air flow...
|
|
Range DTS 7000
Enclosure cooling units for side- or door-mounting
- sealed with protective edging; no extensive work on the installation cutout necessary!
- DTS 7141, 7241, 7341, 7201, 7301: temperature regulated by integrated thermostat
- new standard electronics for DTS 7541 / 7441
- DTS 7541 / 7441 are available as standard with special voltage 380 V / 400 V / 440 V / 460 V / 480 V
|
|
+ filterless maintenance-free
+ cooling performances 600...2000 W (L35/L35)
+ space-saving ex./internal mounting
+ flat design-sheet steel housings
+ customer specific painting
+ stainless steel models
+ Microprocessor controls
+ R134a refrigerant
|
|
Mini size Maxi cooling for small enclosures
+ filterless maintenance-free
+ cooling performance 200...500 W (L35/L35)
+ for external, internal & top mounting
+ flat design sheet steel housings
+ customer specific powder coat painting
+ stainless steel models
+ Micro-processor controls
+ R134a refrigerant
|
|
|
|