|
|
Pitot Tube - Series 160/166/167
Insertion Lengths from 6 to 216 Inches, Designed to Meet AMCA and ASHRAE Code
Ellipsoidal Tip Pitot Tube - Series 160E
Insertion Lengths from 0.2 to 1.52 Meters, Designed to Meet British Standard 1042.
"S" Type Stainless Steel Pitot Tube - Series 160S
Insertion Lengths from 18 to 72 Inches, Designed to Meet EPA Spec. 40 CFR (Ch. 1)
Telescoping Stainless Steel Pitot Tube - Model 166T
Adjustable Insertion Length from 11.5 to 36 Inches
|
|
KIMO offers a wide range of high-quality and accurate Pitot tubes, as per the AFNOR NFX 10-112 and ISO 10780 norms.
Pitot tubes Type L
Accuracy : More than 1 %, for a ± 10 ° alignment to the fluid flow.
Pitot tube with ellipsoidal head. An intake for total pressure and 6 holes for static pressure. Body made of stainless steel.
Pitot tubes Type L with TCK
Accuracy : More than 1 %, for a ± 10 ° alignment to the fluid flow.
Pitot tube with ellipsoidal head. An intake for total pressure and 6 holes for static pressure. Sheated thermocouple K probe integrated, with connection cable length 1,5 m. Body made of stainless steel.
Pitot tubes type S with TCK
Accuracy : More than 4 %, for a ± 15 °alignment to the fluid flow.
Pitot tubes with TIG welding and protective tube made of stainless steel. Sheated thermocouple K probe integrated, with connection cable length 1,5 m. Body made of stainless steel.
|
|
The deltaflow pitot is the portable counterpart of the deltaflow DF 25. It is the ideal sampling instrument for performing integrated measurements according to DIN 2640 standards. It possesses the same highly precise profile as the deltaflow DF25 and is used to verify and calibrate existing measurements. The deltaflow pitot is currently in use, for example, in power plants, by measurement teams, and-in the heating and air conditioning industry-to test airflow efficiency, air intake and exhaust, or to test the efficiency of ventilators.
Because the deltaflow pitot can be disassembled, it can be comfortably transported in a carrying case. Its straight construction design allows it to be easily inserted into the sampling cross-section through previously-existing apertures. The sampling profile is extremely impervious to pollution or to the accumulation of condensation. The highly durable stainless steel and the non-sealed design resist temperatures of 1040°C in constant application and can withstand temperatures of up to 1200°C for temporary measurements.
Media: Gasses
Conduit / Channel Diameter: 100..8500mm
Process Requirements: -250..1200 °C / 0..6 bar
ultra-pure through highly polluted, aggressive gasses
Tests / Certifications:
Calibrated at the Department of Flow Technology at the University of Erlangen
|
|
Single point Pitot Static Tube
FCO65 FCO65
* Classic Prandtl design for most duct sizes.
* Stainless steel construction
* Suitable for temperatures up to 500 degrees C.
* Optional thermocouple for temperature correction
* Versions for installation or hand-held use
Classical precision design pitot static tube for calibrated air flow measurement in various diameters from 2.1mm to 25mm, and custom built in various lengths to suit your application.
|
|
CHARACTERISTICS
Calibrated insertion diaphragm (concentric orifice) with
identification tag for mounting between flanges with
smooth waterproof surfaces.
The upper face of the entrance orifice plate is square
edged.
The pressure measurement taps are on flange or pipe.
Diaphragm with flanges assembly designed to be
welded to pipe.
APPLICATIONS
• Gases, vapours, corrosive and non corrosive fluids.
SPECIFICATIONS
• Maximum working pressure: Limited to
the flange rating.
• Maximum working temperature: Depends on material
and application.
• Range of Pipeline:
Nominal Diameter: DIN or ASA
Rating: DIN or ASA
• Pressure taps: BSP, NPT, METRIC, etc…
• Flange standard: DIN or ASA.
• Flange and accessories material: Depends on pipe.
• Diaphragm material: See 5.1 ORIFICE PLATE &
RESTRICTION ORIFICE.
• Calculations: BS EN ISO 5167-1, 2003, ASME, API, R W MILLER, L W SPINK.
|
|
• Pitot tubes Type L : pitot tube with ellipsoidal head. An intake for total pressure and 6 holes for static pressure. Body made of stainless steel.
• Pitot tubes Type L with TCK : pitot tube with ellipsoidal head. An intake for total pressure and 6 holes for static pressure. Sheated thermocouple K probe integrated, with connection cable length 1,5 m. Body made of stainless steel.
• Pitot tubes type S with TCK : pitot tubes with TIG welding and protective tube made of stainless steel. Sheated thermocouple K probe integrated, with connection cable length 1,5 m. Body made of stainless steel.
• Air Flow Measuring blades DEBIMO : simple and cost effective method of providing permanent air flow measurement in rectangular or circular ducts. When used with a KIMO differential pressure device (pressure, transmitter, electronic micromanometer, liquid column manometer, differential pressure switch, ...).
DEBIMO air flow measuring blades ensure accurate indication, control or recording of air flow velocity and volume. Permit velocity measurements from 3 to 100 m/s (9 Pa to 10000 Pa).
|
|
Sub-Zero Temperatures From Compressed Air
Using only factory compressed air, ITW Vortec's Vortex Tubes generate temperatures down to -40¢XC for spot cooling in a wide variety of industrial applications and processes. A Vortex Tube separates compressed air into hot and cold air streams, lowering the supplied air temperature by as much as 40¢XC and delivering refrigeration up to 6000 BTUH. With no moving parts to break or wear out, Vortex Tubes offer reliable, maintenance-free operation and easy installation. Various models are available for specific cooling requirements and, at only 150 mm to 330 mm long, they serve as a very compact, cooling component on machinery and equipment.
|
|
Vortex Tubes With Metal Generators, Stainless Steel Body:
Vortex Tubes are devices that work on a standard compressed air supply. Air enters the vortex tube and literally splits the air flow into two parts - cold air at one end, and hot air at the other - all without any moving parts.
Vortex Tubes have an adjustable valve at the "hot" end controls the volume of the air flow, and the temperature exiting at the cold end. By adjusting the valve, you control the "cold fraction" which is the percentage of total input compressed air the exits the cold end of the vortex tube.
Inside is the interchangeable brass "generator" which can alter the air used in the vortex tube, and control the temperature ranges you wish to have at the cold and hot ends. There are several ranges of generators for compressed air capacity. There are also two basic types of generators - one to produce the extreme cold temperatures (maximum cold temperature out called the C generator) and one type to produce the maximum amount of cooling (maximum refrigeration called the H generator).
WHY USE Frigid-X Vortex Tubes over others?
Vortex Tubes - Frigid-X are constructed of stainless steel and use a generator and valve made of brass and sealed with viton o-rings to allow their use in the widest range of environments. Others use plastic generators and standard Buna N O-Rings and charge extra for brass and viton. The unique design and quality of materials used in Frigid-XT™ products will deliver years of maintenance-free operation.
Frigid-X™ Vortex Tubes Advantages:
- No moving parts, reliable, maintenance free
- No coolant
- Compact and lightweight
- Low cost application
- Maintenance free units
- Instant cold air in environmental chambers
- No spark or explosion hazard
- Interchangeable generators
|
|
Adjustable Spot Cooler - Frigid-X™ is a low cost and maintenance free Adjustable Spot Cooler system which utilizes a vortex tube to produce cold air at one end.
Adjustable Spot Cooler - Frigid-X™ temperature can be adjusted using a knob at the hot end to set the temperature precisely to your requirements. Temperatures range from approximately minus 30ºF to room temperature and can be easily set with a thermometer.
Adjustable Spot Cooler - Frigid-X™ comes with three brass generators for flow rate adjustment - 15 SCFM (425 SLPM), 25 SCFM (708 SLPM) and 30 SCFM ( 850 SLPM) providing refrigeration up to 2100 BTU/hr (615 Watts).
Features:
- No moving parts or electricity
- Compact and lightweight
- Low cost
- Maintenance free
- Instant cold air
- Quiet
- Magnetic base
- Interchangeable generators
|
|
Vortex Tubes and Spot Cooling Products
EXAIR's stainless steel Vortex Tubes convert an ordinary supply of compressed air into cold air at -50°F (-46°C) on one end, up to 260°F (127°C) on the other. There are no moving parts or refrigerants. They are commonly used to cool electronic controls, machining operations, gas samples, environmental chambers and more.
|
|
|
Vortex Coolers from ITW Vortec keep electrical cabinets and control panels cool, clean and protected. An affordable, maintenance-free alternative to air conditioners, the easy-to-install Coolers have no moving parts to wear out. Vortex Coolers incorporate vortex tube technology that uses filtered compressed air to produce a refrigerated air stream distributed throughout the enclosure. Unlike fans that pull in hot, dirty air, the enclosure Coolers maintain a light positive pressure inside the cabinet to effectively seal out the surrounding contamination, heat and humidity that can wreak havoc on sensitive electronic controls. Refrigerated air produced by the vortex tube enters the cabinet while hot air is expelled through a relief valve. Models are available to deliver up to 5000 BTUH of refrigeration. The UL-listed enclosure cooler systems are thermostatically controlled and are available in NEMA 12, 4 and 4X rated models.
|
|
Cabinet Coolers - Frigid-X™ series for electronic control panels provide a low cost method of both purging and cooling electrical and electronic control panels by using a stainless steel vortex tube to create cold air from ordinary compressed air.
Cabinet Coolers - Frigid-X™ series are compact and can be installed in minutes through a standard electrical knockout. There are virtually no moving parts.
Cabinet Coolers - Frigid-X™ series are ideal for all NEMA 12 and NEMA 4 rated panels.
Advantages:
- Low in cost
- Compact
- No CFC's
- Fast installation
- Stabilize enclosure temperature and humidity
- Virtually maintenance free (No Moving Parts)
- Mounts in a standard electrical knockout
- Stops heat damage and nuisance tripping
- Eliminates fans and filters
- Prevents dirt contamination by keeping enclosure at positive pressure
- Units applicable to all environments including high temperature to 200ºF
|
|
|
A low cost, reliable, maintenance-free solution to a variety of industrial spot cooling problems. Using an ordinary supply of compressed air as a power source, vortex tubes create two streams of air, one hot and one cold, with no moving parts.
|
|
The photomultiplier provides extremely high sensitivity and ultra-fast response. Photomultiplier tubes (PMT) have high bandwidth and noise-free gain on the order of a million. This makes them ideal for the detection of extremely low light or short pulses of light. Photomultipliers can be used to detect photons from 115nm to 1700nm. A typical Photomultiplier consists of a photoemissive cathode (photocathode) followed by an electron multiplier and an electron collector (anode).
Hamamatsu offers the most complete range of head-on and side-on photomultiplier tubes from 3/8" to 20" in diameter.
|
|
Toshiba offers a wide family of thermionic vacuum tube covers X-Ray tubes, X-Ray Image Intensifier, micorwaves tubes and a large variety of proportionnal counters.
Toshiba America Electronic Components, Inc. (TAEC) offers Magnetron Tubes for residential and commercial Microwave ovens as well as imaging system components for a variety of medical, dental and industrial applications. For the latter, the company has established itself as the single source for the complete image chain to meet the needs of all major applications. This product line includes x-ray tubes, a variety of image intensifiers (from 4- to 16-inches), optical units (lens, adapter and cover) and CCD cameras with up to 1K x 1K image resolution. All of TAEC's imaging components offer superior image sharpness, optimized uniformity and maximum image brightness.
|
|
|
Electron multipliers (EMT) are used for the detection and measurement of electrons, charged particles such as ions, VUV radiation and soft X-rays. Hamamatsu electron multipliers have high gain and low noise, making them suitable for the detection of very small or low energy particles. An EMT has CuBeO dynodes for producing gain via secondary emission. The dynodes are connected by a built-in voltage divider (1M ohm per stage) and are supplied in an evacuated glass bulb. The first dynode can be replaced by a photocathode of CsI or KBr for use in VUV photometry. Microchannel Plates (MCP) can also be used as electron multipliers. EMTs are used in applications such as mass spectroscopy, field ion microscopy, electron or VUV spectroscopy, Auger spectroscopy, AES and ESCA.
|
|
| ... products without technical information |
| |
CT water tube type steam generators are the result of over 40 years experience of BONO ENERGIA in the industrial, petrochemical and power generation applications.
Engineered using the most advanced CAD systems, these generators guarantee the highest operating features, thanks to BONO's experience in heat transfer, welding technology and pressure vessel calculations. The production, carried out in Peschiera Borromeo facilities, is based on ISO 9001-2000 quality standards, with inspection plans for material, production process and final test.
CT series water tube steam generators represent a modern concept of "D" shaped desing, having two overmounted drums, expanded vertical tubes and full water walls type furnace. The water circulation inside the boiler is of the natural type.
The burner is housed inside the front water wall by means of properly shaped water tubes.
CONVENTIONAL FIRED WATER TUBES BOILERS (1,000 units world-wide installed)
Model
Clajtub CTD-S / Clajtub CTD
Configuration
Package / Site erected
Medium
Saturated and Superheated steam
Steam production
8 to 150 t/h
Design pressure
up to 80 bar
Steam temperature
300°C - 480°C
Thermal efficiency
up to 94%
Type of fuel
Natural Gas, Fuel Oil, Refinery gas, Lean gas, Reach gas, Coke Oven Gas, Process gas
|
|
Controlled circulation, water tube boilers suitable for the production of hot water, and three gas passes.
They are realized both in vertical and horizontal version. They have elevated efficiencies (>91%) and are tested for pressures up to 36 bar and, for there dimensions, can be installed in reduced spaces.
They produce hot water in only five minutes and have minimum heat dispersions towards the atmosphere which guarantees a higher global efficiency in comparison with a traditional fire tube boiler NPR. Capacity from 116 to 10.000 kW.
|
|
|
OLMAR vertical boilers are of aquatubular type. They are equipped with wide interior drums for water circulation. Its strength and reliability make them especially indicated to be used in hard conditions. At the same time its durability make them the best choice for small and medium-size companies where the working conditions are not the best. In addition to that, its upright position makes them ideal when space is a problem. They are available in small and medium size and with gas and liquid fuel burners.
|
|
STEAM-MATIC SM boilers have been developed upon BONO ENERGIA’s significant technical and technological expertise in manufacturing complex, high-capacity thermal equipment.
With over 10.000 installations worldwide, these boilers represent a remarkable achievement and a valid response to the needs of the industrial market which are combined with reliability and high performance.
STEAM-MATIC SM boilers are reliable: severe quality controls during all productive cycle, hydraulic and fire workshop tests before shipment, easy installation and maintenance represent, together with the proved quality of BONO ENERGIA SPA boilers design, the best guarantee for a very long service life.
STEAM-MATIC SM boilers offer superior performance: the innovative design of the pressure vessel ensures excellent heat transfer in two passes. The large volume of water and a wide steam chamber provide high working flexibility and a considerable steam reserve.
STEAM MATIC SM boilers are low consumption boilers, Bono technology ensures a thermal efficiency of 89% reducing consumption of fuel is to the minumim. Additional devices as Flue gas/air or Flue gas/water economisers or Integrated control system Optispark allow to reach 95%!
STEAM MATIC SM boilers can satisfy steam needs from 1 to 5 t/h.
|
|
The three-pass wetback Yorkshireman range is ideally suited to heavy workloads. Add to this the latest combustion technology and control equipment and you'll achieve impressively low running costs and emissions.
Each boiler is individually tailored to your specific needs and manufactured from start to finish in our own factory. All fittings are mounted in the factory to make installation on site quick and easy.
The boiler can incorporate any make of burner to suit a wide range of gaseous or liquid fuels in single, dual or tri-fuel combinations.
Thermal efficiency (based on NCV) in excess of 90% (94% with the optional economiser unit).
External surfaces are heavily insulated and finished in tough, Aluzinc cladding.
Smoke boxes employ the latest ceramic fibre technology offering significantly less heat loss than traditional refractory.
The Yorkshireman range has larger heating surfaces and steam space than comparable boilers, meaning desirable low heat transfer rates, Low NOX emissions, easily achievable outputs, and quality dry steam throughout the firing range.
A wide range of accessories are available to further enhance the boiler; contact us for more details.
Outputs to 10MW (15,900 kg/hr) and operating pressures to 20 bar(g) available.
|
|
Byworth manufacture fire tube steam boilers in two ranges. The Yorkshireman and Yorkshireman2 ranges are highly fuel efficient three pass wetback steam boilers, available in outputs between 1000 and 18000 kgs per hour and working pressures from 100 to 300 psig (7 to 20 barg). The Yorkshireman2 achieves exceptional efficiency levels by the inclusion of unique XiD fire tubes. These increase the heat transfer from the tube passes by over 80% which in turn leads to overall efficiency of the boiler of around 93%. This is without the incorporation of a flue gas economiser. The Yorkshireman range is highly suited to arduous workloads and is extremely robust.
The MX range of fire tube boilers covers 250 to 5000 kgs per hour and is suitable for lighter workloads.
|
|
The INFRA radiant module is the most classical expression for infrared heating for industrial buildings, sportshalls, ware-houses, poultry farms and glasshouses. The machine is made up of a burner working with forced induction in premix type Baf, with a multi gas head, exhaust fume electro fan, heat exchanger made up of special heat treated steel radiant pipes for high temperature; stainless steel reflecting metallic parabole and support hangers. It has low thermal inertia, and can heat single zones also with limited dimensions activating single modules, it does not move the dust in the air, does not take any space on the floor, it heats the bodies but not the air, so this means that the lower is building insulating, the higher are fuel savings that are achived with infrared radiant tubes.
|
|
Equipments suited for all environments with great height (form 4 to 20 meters) or with high thermal dispersion.
It includes a burner unit and a heat exchanger tube which reaches the temperature of 400 ÷ 550 °C., providing a very high radiation efficiency, also by means of the reflecting cover located over the tubes, which focuses the thermal flow downwards.
By means of a centralized equipment control system it is possible to heat only the areas concerned by operations
|
|
|
