|
|
EE65 Series
Air Velocity Transmitter for HVAC Applications
EE65 air velocity transmitters are ideal for accurate ventilation control applications. They are operating on an innovative hot film anemometer principle.
The E E thin film sensor guarantees very good accuracy at low air velocity, which is not possible for conventional anemometers with commercial temperature sensors or NTC bead thermistors.
EE65 series are available with current or voltage output, the measuring range and the response time can be selected with jumpers by the user.
Low angular dependence enables easy, cost- effective installation
EE66 Series
EE75 Series
High-Precision Air / Gas Velocity Transmitter for Industrial Applications
The EE75 series air velocity transmitters were developed to obtain accurate measuring results over a wide range of velocities and temperatures.
A high-quality hot film sensor element based on cutting- edge thin film technology ensures maximum sensitivity, even at lowest mass flows.
At the same time, the innovative probe design produces reliable measuring results at high flow velocities of up to 40m/s (8000ft/min). The integrated temperature compen- sation minimises the temperature cross-sensitivity of the EE75 series which, combined with the robust mechanical design, allows it to be used at process temperatures between -40 to 120°C (-40 to 248°F).
EE57 Series
|
|
AFM series Flow Transmitter is designed for monitoring and transmitting liquid flow rate reading to PLC, or to control device in process control system, and perform flow control monitoring, filtration or softener regeneration, pump protection, feed pump pulsing, ratio control water distribution or leak detection, etc.
-Dual HIGH/LOW alarm set point
-Modbus RS485 output (Optional)
-Offer both analog and digital output
-Provide flow rate and accumulated value
-Dual accumulated value display
-Micro-electronic design, compact size, anti-interfere, LCD display with backlight for easy and clear calibration
|
|
Thermatel® Model TA2 Thermal Mass Flow Transmitter provides reliable mass measurement for air and gas flow applications. The powerful, yet easy to use, electronics are contained in a compact explosion proof enclosure. The TA2 offers excellent performance at exceptional value.
Probes can be provided with a variety of process connections, including threads, flanges, or installation through a compression fitting. The sensor will fit pipe sizes of 1 1/2" diameter or larger (2" minimum size with thread connection).
The sensor is protected to prevent damage due to “bottoming-out” if inserted too far into a pipe. When using an insertion probe with compression fitting, the user can adjust the position of the sensor in the pipe to obtain the optimum location. Typically, this will be with the bottom of the probe 1.0 inch (25 mm) lower than the center line of the pipe.
|
|
¨ DC or AC powered.
¨ Pulse and analog output scaled per unit of measure.
¨ Optional Hi and Lo alarms.
¨ Flowmeter Linearization.
¨ Factory configured when purchased with a Hoffer
flowmeter.
¨ Several Enclosure options.
¨ CE Compliant.
¨ Windows® Configuration Software
|
|
Flow Measurement
Honeywell's flow transmitters measure differential pressure, absolute or gauge pressure and process temperature.
Smartline Configuration Toolkit
Honeywell's Smartline Configuration Toolkit (SCT 3000) is an engineering and maintenance tool designed to complement the Honeywell Smart Field Communicator. The SCT 3000 allows easy access to all Smartline configuration database parameters using Windows technology.
SMV 3000 Smart Multivariable
Honeywell's SMV 3000 Smart Multivariable Flow Transmitter measures three separate process variables simultaneously with the ability to calculate compensated mass or volume flow rate as a fourth process variable according to standard industry methods for air, gases, steam and liquids.
MCToolkit
The Honeywell MC Toolkit Configurator is a Pocket PC-based engineering and maintenance tool for configuring, monitoring, diagnosing and managing smart field instruments/devices.
VersaFlow, Coriolis
The VersaFlow mass flow sensor reliably measures mass flow, density, volume, temperature, mass or volume concentration, and solids content
VersaFlow, Magnetic
The VersaFlow Mag 4000 is suitable for the most demanding applications. All meters consist of a sensor and a converter that may be integrally or remotely mounted.
VersaFlow, Ultrasonic
The Honeywell VersaFlow Sonic 1000 is an ultrasonic clamp-on flowmeter that can be mounted on the outside of a pipe to measure the flowrate of liquids.
VersaFlow, Vortex
The VersaFlow Vortex 100 is the only vortex flow meter with integrated pressure and temperature compensation in 2-wire technology
|
|
Flow Measurement
Honeywell's flow transmitters measure differential pressure, absolute or gauge pressure and process temperature.
Smartline Configuration Toolkit
Honeywell's Smartline Configuration Toolkit (SCT 3000) is an engineering and maintenance tool designed to complement the Honeywell Smart Field Communicator. The SCT 3000 allows easy access to all Smartline configuration database parameters using Windows technology.
SMV 3000 Smart Multivariable
Honeywell's SMV 3000 Smart Multivariable Flow Transmitter measures three separate process variables simultaneously with the ability to calculate compensated mass or volume flow rate as a fourth process variable according to standard industry methods for air, gases, steam and liquids.
MCToolkit
The Honeywell MC Toolkit Configurator is a Pocket PC-based engineering and maintenance tool for configuring, monitoring, diagnosing and managing smart field instruments/devices.
VersaFlow, Coriolis
The VersaFlow mass flow sensor reliably measures mass flow, density, volume, temperature, mass or volume concentration, and solids content
VersaFlow, Magnetic
The VersaFlow Mag 4000 is suitable for the most demanding applications. All meters consist of a sensor and a converter that may be integrally or remotely mounted.
VersaFlow, Ultrasonic
The Honeywell VersaFlow Sonic 1000 is an ultrasonic clamp-on flowmeter that can be mounted on the outside of a pipe to measure the flowrate of liquids.
VersaFlow, Vortex
The VersaFlow Vortex 100 is the only vortex flow meter with integrated pressure and temperature compensation in 2-wire technology
|
|
| ... products without technical information |
| |
FEATURES RHE 07
- Rack mounting version
- Allows to operate fl ow sensor in hazardous area, optional:
ATEX Approval Ex II (1) G [EEx ia] IIC or CSA 220705 - Class 1, Div 2
- 2 analog outputs (0/4 - 20/22 mA)
- 1 pulse/frequency output - 2 inputs
- Available in all common supply voltages
- Multifunctions (density, brix, concentration...)
- Version available with RS 422/485/232
- Protection class: IP 20 / Nema 1
- Power consumption: < 15 W
- Temperature range: -40 to +60°C
- NMI custody transfer approved version available (TC 3382) with double pulse output Batch control
|
|
Order Code M-RTU:
- Configuration I/O: 4 DI, 2 AI, 2 DO (version GP), 2 DI, 2AI (version PC)
- Integrated Modem GSM Full Type Approval
- Memories: EEPROM 64 KB, Flash 2 MB
- Temporary turn on for sms receiving / sending
- Data transmission on event or on demand
- IP44 external case
- 14,4 V battery power supply, 3 years life-time
|
|
Wireless I/O solutions from Phoenix Contact offer flexible and reliable data transmission for your applications. Monitoring and controlling your processes is reliable with point to point, and multipoint to point industrial radios.
These industrial radios can be incorporated into controlling pump stations, monitoring tank levels and sensors as well as a variety of additional industrial applications.
|
|
PERFORMANCE
Power Output: 500mW@5V(Default), 1W@9V(customized)
RF Line-of-sight Range: 4000m@1200bps, 2000m@9600bps
RF Effective Rate: 1200/2400/4800/9600/19200/38400bps optional Receiver Sensitivity: -124dBm@1200bps, -118 dBm@9600bps
Supply Voltage: +4.75~5.5VDC
Transmit Current: <400mA@500mW, <500mA@1W
Receive Current: <40mA
Sleep Current: <5µA optional ex-factory
Frequency Band: 433MHz(Default)
400MHz~470MHz(customized)
Channel: 8(Default), 16/32 (customized)
Default Interface: COM1:TTL/UART,COM2:Non-Standard RS232 or RS485
Size: 53mm×38mm×10mm
Weight: 34g
Antenna Base: 50Ω
Operating Temperature: Industrial: -35℃~+80℃(TCXO crystal)
Commercial: -20℃~+60℃
Frequency Stability ±2.5ppm Industrial
±10ppm Commercial
|
|
25kHz UHF Narrow Band FM Multi Channel Transmitter and Receiver.
The TLC2H transmitter and RLC2H receiver offer a low power, reliable data link in an industry standard pin out and foot print.
This makes the TLC2H/RLC2H pair ideally suited to those low power applications where existing wideband modules have insufficient range, or where low cost multi-channel operation is needed without compromising on RF specification or regulatory requirement.
|
|
The TriQuint TGA2803-SM is an ultra- linear, packaged TIA/Gain Block which operates from 40MHz to 1000MHz.
The TGA2803-SM typically provides flat gain along with ultra-low distortion. It also provides high output power with low DC power consumption.
This amplifier is ideally suited for use in CATV distribution systems or other applications requiring extremely low noise and distortion.
|
|
ALMEMO transmitters are ideally suitable for a decentralised, networked data acquisition. Measuring data can be locally acquired using short sensor signal lines and small modular measuring instruments and can be evaluated together on a measuring computer. As a result, this does not only minimise the wiring efforts but it also significantly reduces EMC problems. This allows for measurement setups with a very flexible application of the devices, so even the most demanding measuring tasks can be solved. To ALMEMO transmitters various sensors can be adapted for the measuremt of all kind of physical, chemical and electrical variables.
|
|
|
Wireless interface products provide a cost effective alternative to expensive hard wired connections. The wireless product provides continuous, 24/7 communication using the FCC licenses free 900MHz frequency. Using Frequency Hopping Spread Spectrum (FHSS) technology, a robust signal is provided that is virtually free from disruption due to interference. This technology has been proven in thousands of installations worldwide.
|
|
XYR 5000 Wireless Transmitters
Honeywell's award-winning XYR 5000 wireless transmitters deliver value beyond wiring savings, optimizing the plant with data previously unavailable to the control system.
XYR 5000 Absolute
Honeywell WG/A510 wireless transmitters cover a wide pressure range, and can be used to monitor a variety of processes and assets in hazardous and remote areas.
XYR 5000 Acoustic
Honeywell's WN571 acoustic transmitter is used to monitor applications that may generate high frequency noises when they malfunction. It can be configured to detect abnormal asset conditions and contains a built-in temperature sensor.
XYR 5000 Analog Input
Honeywell's WI550 Analog Input Field Transmitter is used to add wireless capabilities to new or existing analog transmitters, such as pressure, temperature, level, flow meters, pH meters or any device that has voltage (0-10 V) or current (4-20 mA) outputs.
XYR 5000 Base Radio
Honeywell's Wireless Base Radio (WBR) combines an RF transceiver and the interface to a SCADA, DCS or data acquisition device.
XYR 5000 Base Radio Antenna
The Wireless Base Radio (WBH) is part of the XYR 5000 family of wireless products. It combines an RF transceiver and the interface to a SCADA, DCS or data acquisition device.
XYR 5000 Differential
Honeywell's WD520 wireless transmitters can be set to operate in four modes: differential pressure, orifice flow, open channel flow and level.
XYR 5000 Dual Discrete
The WW591/592 Dual Discrete Input Field Transmitter is part of the XYR 5000 family of wireless products. It is used to transmit the status of contact switches.
XYR 5000 Gateway
Honeywell's Gateway enables recognition of the XYR transmitters by the Honeywell TDC/TPS system. Setup, receipt and presentation of data collected from the XYR Base Radio is completed with minimal effort.
XYR 5000 Temperature
The WT530 Temperature Transmitter is part of the XYR 5000 family of wireless products. These wireless temperature transmitters can be used to monitor a variety of processes in hazardous and remote areas.
XYR 5000 Wireless Toolkit
Honeywell's Wireless Management Toolkit is the services management software for the wireless product family, including XYR 5000 component management, process monitoring in real time and data acquisition.
|
|
XYR 5000 Wireless Transmitters
Honeywell's award-winning XYR 5000 wireless transmitters deliver value beyond wiring savings, optimizing the plant with data previously unavailable to the control system.
XYR 5000 Absolute
Honeywell WG/A510 wireless transmitters cover a wide pressure range, and can be used to monitor a variety of processes and assets in hazardous and remote areas.
XYR 5000 Acoustic
Honeywell's WN571 acoustic transmitter is used to monitor applications that may generate high frequency noises when they malfunction. It can be configured to detect abnormal asset conditions and contains a built-in temperature sensor.
XYR 5000 Analog Input
Honeywell's WI550 Analog Input Field Transmitter is used to add wireless capabilities to new or existing analog transmitters, such as pressure, temperature, level, flow meters, pH meters or any device that has voltage (0-10 V) or current (4-20 mA) outputs.
XYR 5000 Base Radio
Honeywell's Wireless Base Radio (WBR) combines an RF transceiver and the interface to a SCADA, DCS or data acquisition device.
XYR 5000 Base Radio Antenna
The Wireless Base Radio (WBH) is part of the XYR 5000 family of wireless products. It combines an RF transceiver and the interface to a SCADA, DCS or data acquisition device.
XYR 5000 Differential
Honeywell's WD520 wireless transmitters can be set to operate in four modes: differential pressure, orifice flow, open channel flow and level.
XYR 5000 Dual Discrete
The WW591/592 Dual Discrete Input Field Transmitter is part of the XYR 5000 family of wireless products. It is used to transmit the status of contact switches.
XYR 5000 Gateway
Honeywell's Gateway enables recognition of the XYR transmitters by the Honeywell TDC/TPS system. Setup, receipt and presentation of data collected from the XYR Base Radio is completed with minimal effort.
XYR 5000 Temperature
The WT530 Temperature Transmitter is part of the XYR 5000 family of wireless products. These wireless temperature transmitters can be used to monitor a variety of processes in hazardous and remote areas.
XYR 5000 Wireless Toolkit
Honeywell's Wireless Management Toolkit is the services management software for the wireless product family, including XYR 5000 component management, process monitoring in real time and data acquisition.
|
|
The Single Sensor Wireless I/O range of products is suitable for connecting to a single sensor. Capable of being powered by battery only supplies.
Typical Applications
Connection of flowmeters or energy meters
Monitoring of storage tanks
Monitoring of cathodic protection on pipelines
Wireless alarms from power reticulation fault-relays
Features
Two digital/pulse inputs and one analog input
Extremely low power consumption by reverting to "sleep" mode
Multiple power supply options including battery-only supply
Weatherproof enclosures
Easy installation and configuration
WIB-net intelligent wireless protocol, peer-to-peer communications; exception reporting; reliable self-checking messages; highly secure data encryption
Set-point status on analog input available as an "internal" input.
Can connect to up/down counter transducers such as shaft-encoders
Internal monitoring and alarm on low supply voltage - this alarm can be transmitted by radio
Easily configured to repeat the transmission several times, ensuring transmission is received
Used in conjunction with Multi I/O and Data Bus Interface units which act as receiver units
|
|
SATELNODE X8SR is the basic VHF receiver of the SATEL local area transfer system. Together with SATELCODE alarm transmitter from SATEL, it provides the easiest way of setting up a wireless alarm transfer system.
The SATELNODE X8SR comprises of a high quality radio receiver with excellent selectivity and stability.
It is capable of processing coded messages from SATELCODE transmitter.
The SATELNODE X8SR is also equipped with an RS-232 interface, which provides a flexible means of programming the radio modem with a PC, to meet the varying needs of applications.
By means of the SATELCODE / SATELNODE alarm transfer equipment, SATEL has drastically lowered the threshold of setting up a local alarm transfer system.
SATELCODE is a versatile VHF radio transmitter from SATEL's extensive selection of radio modems. Together with its counterpart, the SATELNODE receiver, it provides the easiest way of setting up a wireless alarm transfer connection between two points.
The SATELCODE transmits a message that includes both address and alarm information. The number of possible different messages amounts several tens of thousands.
The configuration of a SATELCODE / SATELNODE system is straightforward and the installation quick and easy. The user benefits from minimum time spent in planning and materialization fo an alarm system. The radio modems are extremely reliable. The operation costs of the alarm transfer system are low, as there are practically no network charges.
|
|
| ... products without technical information |
| |
|
|