|
|
|
|
|
|
* P/N:FS-101
This is a standard model FS-100, Made of Plastic, lower cost, with 3/4"FNPT mounting threads, Using this in-line flow switches to monitor min/max values of liquid flow in order to switches a valve or to establish an on or off control loop, electrical circuit is isolated from the fluid path. Such as boiler system.
* P/N:FS-201
The product model is FS-200, Made of brass C37700 material, with 3/4"FNPT mounting threads,Using this in-line flow switches to monitor min/max values of liquid flow in order to switches a valve or to establish an on or off control loop, electrical circuit is isolated from the fluid path. Such as the coolant water system of welding machine.
* P/N:FS-301
The new developed FS-300 flow switches is made of SUS304 material, with 3/4"FNPT threads, with proven accuracy, ideal for critical low flow or high flow protection applications such as pump seal cooling water, pump inlet flow protection, cooling circuit protection, High and low flow rate alarm, valve failure, pump starting or failure, pipe blockage or rupture.
* P/N:FS-401
FS-400 flow switches, made of SUS304 material,with 1/2"FNPT mounting threads,with proven accuracy, ideal for critical low flow or high flow protection applications such as pump seal cooling water, pump inlet flow protection, cooling circuit protection, High and low flow rate alarm, valve failure, pump starting or failure, pipe blockage or rupture.
|
|
General description :
New Swafer™ Micro-Channel Wafer Technology
PerkinElmer’s new Swafer™ micro-channel flow technology is an innovative and user-friendly approach for flow-switching applications – it delivers unparalleled hardware and application flexibility, expanding the capabilities of capillary gas chromatography.
- Richer sample information on difficult or otherwise impossible separations
- Easy setup and configuration changes without requiring service intervention
- Combine injection techniques (HS, ATD, liquid, etc.) based on sample
requirements
- Unparalleled application flexibility through 13 user-interchangeable
configurations
|
|
|
|
|
|
AALBORG®'s 150mm High/Low Flow Meter with OPTICAL SENSOR SWITCH is a non-invasive means for detection of a HI or LOW flow. This SENSOR is ideal for signaling alarm, cutoff valve or other device when the float passes the detector (alarm, valve, etc. not included).
A small LED sensor and receiver are mounted on one side of the flow meter. The float inside the tube is detected as it passes across the beam of light. The SENSOR can be used to detect the float passage beyond the SENSOR's set-point or to monitor the float position at a specific level signaling when the float isoutside the range of the SENSOR's light beam.
When performing OEM applications, its compact design and ease of application make it a non-obstrusive, simple-to-use addition to your flow meter.
Use whenever maximum or minimum flow levels need to be monitored automatically. AALBORG®'s OPTICAL SENSOR SWITCH can be used in conjunction with a control relay to power alternate equipment or monitoring devices.
It also helps protect your processes and equipment from damage caused by extreme flow rates.
|
|
Adjustable Flow Switch - Series AFS
For Oils, Water and Gases, Infinite Adjustments
Brass Flow Switch - Series P1
Flow Rates from 0.10 to 1.5 GPM, Fixed Setpoint
Flow Switch - Series P2
Flow Rates from 0.5 GPM to 5 CFM, Fixed Setpoint
Polypropylene Flow Switch - Series P3
Flow Rates from 0.25 to 2.0 GPM, Fixed Setpoint
PPS Piston Flow Switch - Series P4
Flow Rates from 0.1 to 1.5 GPM, Fixed Setpoint
PVC Shuttle Flow Switch - Series P5
Flow Rates from 0.5 to 2.0 GPM, Fixed Setpoint
|
|
Flow meters for liquids with numerous custom options.
Designed specifically for use with alimentary fluids, the material is also suitable for a wide range of other applications
|
|
|
FCI flow switches feature Thermal Dispersion technology in which the temperature difference is greatest in a no-flow condition and decreases as flow increases, cooling the heated RTD. Changes in flow velocity directly affect the extent to which heat dissipates and, in turn, the magnitude of the temperature difference between the RTDs. An electronic control circuit converts the RTD temperature difference into a DC voltage signal. Both of these signals are provided at output terminals and are used to drive two adjustable-setpoint alarm circuits. Both alarms are independently field configurable for flow, liquid level/interface or temperature operation.
|
|
|
|
|
|
Reliable - Safe – Proven !
Our tried-and-tested flow monitoring switches are used for two basic purposes:
- To ensure a minimum flow rate, e.g. of cooling water or lubricating oil (protects against running dry).
- To start a technical procedure when the flow begins.
Function
The flow monitoring switch comprises a paddle system to whose end a permanent magnet is attached. Above this magnet is a reed contact, located outside the flow of fluid. A second magnet with opposing poles creates the force necessary to reset the switch back to the no flow position.
When the flow being monitored pushes against the paddle system, the paddle swings away. This changes the position of the magnet in relation to the reed contact and thus activates the contact.
As soon as the flow is interrupted, the paddle moves back to its starting position, thus activating the reed contact once again. The force necessary to push the magnet back is provided by the two magnets repelling each other.
Using magnetic force instead of the usual leaf spring means that the switch is considerably more stable in the long term and much less sensitive to pressure peaks.
|
|
|
|
|
|
Sierra's Innova-Switch™ flow and level switches represent the state-of-the-art in gaseous and liquid flow switching or liquid level control. Innova-Switch was designed to meet a broad range of performance and environmental application requirements. The sensor and other wetted materials are 316L stainless steel and feature all welded construction with no moving parts. The Innova-Switch is easy to install and adjust, giving reliable, low maintenance performance in the most demanding applications.
UNIQUE PRODUCT FEATURES
-Range of 0.01 to 5 fps in liquids and 0.1 to 500 fps gases
- Fast response time of 0.5 to 10 seconds (media dependent)
-Wide operating temperature range of -100F to +390F (-70C to 200C)
- Operating Pressure: to 3000 psia (207 bar)
-CE, CENELEC and CSA approval
- Repeatability: +/- 1% of set point (Flow) or 1/32" (0.8mm) Level
-Stability: Drift <0.5% from calibrated set point over a range of +/-50F
- Temperature compensated through entire range
-Enclosure: Explosion Proof; NEMA 3, 4X, 7, 9. CSA, FM, UL, CENELEC and EECS approved
- Process Connection: 0.75" MNPT standard. 0.5" and larger MNPT and various other process connections such as sanitary and flanges optional
- Insertion Length: 2.0" standard. 0.5" or greater optional
- Input Power: 115 VAC, 50/60Hz standard. 230 VAC, 50/60Hz optional, 24VDC optional. 3.1 Watt maximum
- Output: 5A. 250 VAC. DPDT with fail safe capability
|
|
Novafix MR1K-...GM/GK
Mechanical Flow Switch for liquids or gaseous media with spring supported piston and magnetic actuation of a reed switch. Robust design produced in materials brass or stainless steel.
compact dimension
good repeatabilty
dirt-resistance
high switch capability
hermetic separation of mechanical and electrical component
|
|
Novafix HD2K-...GM/GK
Mechanical Flow Switch for liquids media, with spring-supported piston and magnetic triggering of a reed switch. Rugged construction in brass or stainless steel with additional viscosity compensation.
viscosity compensation 30-330mm²/s
good repeatabilty
high switch capability
hermetic separation of mechanical and electrical component
exact setting of switch via scale + gear
|
|
Fluvatest UR3K-...GM/GK
Instruments operate by a spring-supported paddel with magnetic triggering of a reed switch.
good repeatability
low pressure loss
hermetic separation of electrical and hydraulic components
easy adjustment of switch
|
|
|
FCI liquid level/interface switches feature Thermal Dispersion technology in which the temperature difference between the two RTDs is greatest in the absence of liquid and decreases when the level element is submerged, cooling the heated RTD. An electronic control circuit converts the RTD temperature difference into a DC voltage signal. Both signals are provided at output terminals to drive two adjustable-setpoint alarm circuits. Both alarms are independently field configurable for liquid level, interface or temperature operation. Since all process media exhibit different heat transfer capabilities, highly sensitive FCI liquid level/interface controllers may be specifically calibrated to detect difficult interfaces between fluids -- including liquids, gases, slurries and foam regardless of their physical properties.
|
|
Thermatel® has demonstrated reliable performance as a flow or level switch. For use as a flow switch, Thermatel can be used to detect either a high flow or a low flow condition for both gases and liquids. For a level switch, Thermatel can be used to detect difference in thermal conductivity of various media. This includes interface detection between media such as liquid/foam, oil/water and even liquid/solid.
Thermatel probes are available in 316L Stainless Steel, Hastelloy C, or Monel with all welded construction. The technology has no moving parts providing excellent reliability.
|
|
Control Flow from outside a pipe. Recommended for "difficult liquids" including wastewater, slurries, sludge, chemicals, viscous liquids and abrasives. The Greyline DFS-II is ideal for pump protection or to activate flow/no-flow alarms.
- Non-Contacting Ultrasonic Sensor
- Easy Calibration
- Accurate and Repeatable
- 5 amp DPDT Control Relay
- Adjustable ON/OFF Set-Points
- Adjustable Time Delay
- Relay Status LED
- Intrinsic Safety Option
|
|
Novafix VD-...GR
Mechanical Flow Switch for liquids or gaseous media, with contactless triggering of an adjustable reed switch.
Rugged design in brass / bronze combination.
good repeatability
dirt-resistant
exact setting of switch via scale
|
|
vent-captor - Insertion type Air Flow Switch for gaseous media
Compact Air Flow Switch for AC/DC Applications
Adjustable Set-Point between 1 m/s and 10 m/s
For general applications
Compact Air Flow Switch for DC Applications
High accuracy Set-Point adjustable between 0.5 m/s and 20 m/s
For critical Applications
Easy installation with Special Flange (supplied), or optional pipe adaptor
|
|
Delta Controls' flow meters are proven in a broad range of air and gas management applications, including:
-Blow-by gas measurement in engine test beds
-Nuclear, biogas, pharmaceutical, industrial process gas and pollution monitoring
To support both existing and new customers with a high level of meter performance and minimal long-term cost of ownership, Delta offers an extensive recalibration service. Utilising the in-house flow laboratory, quick turnarounds can be achieved to minimise customer downtime.
Delta also offers an ATEX approved, vane operated flow switch, ideally suited to ducted air system applications in hazardous environments.
|
|
|
Hedland manufactures one and two-relay flow switches as well as analog-output flow transmitters. Switch options include SPDT, SPST-NO, and SPST-NC. Flow transmitters include a field-selectable 4-20 mA, 0-5 Vdc and 0-10 Vdc analog output. The flow switches and transmitters are available for almost all mediums including oil, air and other gases, and water and other liquids. Accuracy of +/-2% of full scale. Port sizes from 0.5 to 1.25", available with SAE, BSP or NPT threads. Special scales available.
|
|
- Piston type
- Liquids application only
- Magnetically actuated switch head
- Brass material
- 1/2" male thread process connections
- Fixed switch piont from 0,8 to 7 l/min. (1 Cst)
- N.O. reed switch 250Vac - 0,5A - 70VA
- Max pressure 15 bar
- Max temperature 110°C
- Protecion IP40 - IP65 with cap
|
|
Compact Metering Flow Switch with analog display
1/2" Thread (NPT or BSP)
Easy to install
Set point adjustable over full measuring range
Flow range adjustable for best resolution
Indexed range pot enables flow rate measurement
|
|
SERIES AP 74 VERTICAL FLOW SWITCH Ultraclean safety device for gases
Selection and sizing application program online at www.aptech-online.com
Flow thru design free of deadlegs or unswept zones SS 316L VAR secondary remelt material 15 or 10 μin. Ra max electropolished finish Vacuum to 3,500 psig (241 bar) Particle free operation Six flow reference trip points: 2, 5, 10, 25, 50 & 100 slpm at 100 psig of N2
|
|
|
FLS are flow switches used to check the fluid crossing in lubrication circuits and to activate an electrical alarm signal in case of flow decrease under the setting value
|
|
|
Designed with body in aluminium, nickel-plated brass or 304 stainless steel. Execution with visual indication only, graduated scale on the glass tube, max. pressure 15 bar and 0,1 to 60 LPM flow rate; electric execution with visual indication, 1 or 2 adjustable alarm points, max. pressure 15 bar and 0,1 to 60 LPM flow rate; simple electric execution with 1 or 2 adjustable alarm points, max. pressure 150 bar, 0,1 to 140 LPM flow rate. All these models can be supplied with specific springs depending on the fluid viscosity up to 200 Cst. Electric execution for water application with 1 or 2 adjustable alarm points, 0,3 to 60 LPM flow rate, max. pressure 50 bar.
|
|
- Piston type
- Fluid : Water , oil , other liquid available
- Flow range : 15 ~ 24000 l/h (at Water)
- Accuracy : ± 3 % F.S , On request : ± 2.5 % F.S
- Size : 1/4" to 2-1/2"
- Connection Size : NPT , Flange Type on Request
- Working Limits : Temperature : -10°C to +150°C
- Max. Pressure : 30 kg/cm²
- Housing enclosure : IP 65
- Housing material :
NS,CS,MS types-Aluminum Alloy
ES type-316SS
- Lens material:Safety glass
- Mounting:Vertical,horizontal available
- Materials : Brass , 316SS wetted parts
- Alarm switch : Micro switch,inductive switch available
|
|
Flowmeters, Switches, and Transmitters
Flowmeters from Orange Research provide accuracy and reliability in an affordable, rugged package. These industrial quality flowmeters combine modern technology and materials with a familiar easy-to-read pointer and dial gauge. A patented magnetic movement allows flow sensing at high line pressures and operation in any orientation.
|
|
- Piston type
- Liquids and gas application
- Interchangeable switch head
- Nickel plated Brass or St. Steel
- 1/4" to 1" female thread process connections
- Adjustable reanges from 0,04 to 60 l/min.
- SPDT reed switch 250 Vac - 1,5A
- 200 bar working pressure, 400 bar on request
- Max working temperature 200°C
- Protection class IP65
|
|
- Easy direct-installation into the existing pipe
- A wide range of pipe sizes from diameter 25 ~ 200
- Adjustable set point
- Reed switch provides a SPDT contact function
|
|
- Paddle type
- Liquids application only
- Interchangeable switch
- Materials: Brass or St. Steel
- From 3/8" to 2" Gas-F process connections
- Adjustable ranges from 3 to 53 l/min. (1 Cst)
- N.O. or N.C. reed switch 250Vac - 1.5A - 50VA
- Pmax = 25 bar - Tmax = 110°C
- Protection class IP65
|
|
FQS Flow Switch is for use on liquid lines such as water, ethylene glycol or any non-corrosive fluid in chillers, pumps, condensers, boilers, industrial equipment, etc.
One model for pipe connections from 1 to 6 in.
Flow and pipe diameter determines use of 1, 2 or 3 paddles.
|
|
Switching range 2,5-4,8 l/min....383-533 l/min. water
Connection G 1/4... G 1 1/2, 1/4...11/2 NPT
(via T-fitting up to DN 200)
Material brass, st. st.
Max. pressure 100 bar (brass), 250 bar (st. st.)
Max. temperature 110 °C
Reed contact
|
|
|
|
