|
|
Using the CENTOR technology, the CENTOR W digital torque gauges have a very large graphic display and show a maximum amount of information for more efficient measuring: they show the current reading and the peak value at the same time, and a bar graph to show the operator whether they are close to their maximum capacity. If necessary, the backlighting can be used to further enhance reading comfort.
Its advanced measurement chain enables it to use a sampling rate of 1,000 Hertz with a resolution of 1/10,000 FS and a total error of less than 0.5% FS.
Many other functions complete the possibilities of the gauge:
the Set point functions can be used to carry out “OK, NOK” tests: a symbol appears on the display.
The fully programmable RS232 output sends the data to a PC. A digimatic output can be used with Mitutoyo statistical printers.
|
|
Atlas Copco provides a complete line of products for measuring torque, angle, pulses and speed within all types of assembly industry.
The ACTA 3000 enables you to perform a full range of functions, from simple torque checks to advanced graphic tightening analysis. It comes in different models to cover all your needs, and is upgradeable. The ACTA 3000 together with the Tools Talk ACTA software, is the user friendly complete quality management system! The system will automatically give you information when the tools are due for calibration. With ACTA 3000 it's possible to have all tools, the tightening database and supplier database organized all in one place. With the ToolsTalk ACTA software and you have a complete quality management tool at your service or your complete ISO 9000 under one icon in your PC. Quality management has never been easier!
Atlas Copco provide instruments that will measure torque from 0.05 Nm up to 3.500 Nm.
|
|
|
By automated and manual procedures, DSM tightening tools of the BL/BLH series take care of a reliable tightening operation. Low-friction mounted gearing stages and the maintenance-free brushless motor guarantee a maximum quiet running or the tightening tools. Different types from a torque between 0,5 Nm and 2000 Nm are available. A self-resilient torque and angle of rotation transducer additional increases the tightening safety. Torque and angle of rotation transducers assure a 100 % tightening connection by all types. By the own production are customised executions possible at any time.
|
|
The screwdriving-process could be evaluated with regard to :
- cutting torque
- treshold torque
- shut-off torque
- actually achieved torque
|
|
|
With the boxes of measurement of couple Weber: finished the long discussions concerning the couples of screwing.
|
|
Chatillon® DFE Series
The Chatillon® DFE Series is a compact, easy-to-use force gauge designed for economy applications without compromising functionality. Ideal for handheld or test stand applications, the DFE is available with capacities from 2 lbf (1 kgf, 10 N) to 500 lbf (250 kgf, 2500 N). The DFE features an integral loadcell with a measurement accuracy of better than 0.25% full scale. A large, easy-to-read, high resolution dot matrix LCD display supports a variety of standard gauge functions including normal and peak readings, high/low limits, setpoints, pass/fail results, statistical results, loadcell actuation and direction. Loads are displayed in ozf, gf, lbf, kgf and N units. The display can be inverted and displayed results may be "hidden" from the operator. The DFE gauge may be specified with or without RS232 serial communication. All DFE Series force gauges come with a carrying case, battery adapter/charger, testing accessories and NIST Certificate of Calibration with data. Uncertainty data per ISO/IEC 17025 is supplied standard.
Standard Gauge Measurement Functions
Normal Tensile and Compression Measurement
Peak Tension and Compression Measurement
Pass-Fail Limits
High & Low Setpoint Limits
Statistical Calculations
|
|
Mecmesin digital force gauges are state of the art instruments, specifically designed to measure force in tension and compression (push or pull) with optimum precision and performance.
The Advanced Force Gauge (Mark 4) is the most versatile and fully-featured instrument offered by Mecmesin. The AFG comprises of 10 different models ranging from 2.5N to 2.5KN with the added ability of 1st peak and ultimate peak hold. The bi-directional interface (RS232, Mitutoyo, Analogue) ensures full data transfer between PC's, data-loggers and Mecmesin stands. All AFG's feature superb accuracy at ±0.1% of full scale and a sampling rate of 5,000 times per second.
The BFG (Basic Force Gauge) range of rugged, flexible and reliable instruments are designed for easy operation and outstanding force measurement performance - all at a budget price. A precise and reliable instrument, the BFG features accuracy at ±0.25% of full scale and a sampling rate of 1,000 times per second.
The CFG (Compact Force Gauge) is a pocket-sized, lightweight and low-cost force gauge, ideal for performing elementary tension and compression testing. The CFG is available in 3 capacities and features include a data sampling rate of 10Hz, accuracy of ±0.5% and versatile measurement options lbf, N, ozf, kgf and gf, with a resolution of 1:1000 or better.
Used either handheld or combined with a test stand and accessories they offer a complete testing solution for a virtually limitless range of tension and compression applications.
|
|
Simple digital force gauge : CENTOR FIRST
Simple and yet complete, the CENTOR First force gauge uses efficient technology to simplify force measurements, in tension and compression ...
Graphical force gauge : CENTOR EASY
Simple and complete,the CENTOR "Easy" is the best instrument for measuring in the workshop.The screen provides simultaneous readout of the current and maximum values as well as...
Advanced graphic dynamometer : CENTOR STAR
The CENTOR "Star"has many functions.It will become your preferred force measurement tool.The graphic screen displays the complete Force=F(t) curve ,...
Two sensors force gauge : CENTOR DUAL
It has all the functions of an STAR force gauge, but its calculation power enables it to record values sent by 2 different sensors simultaneously
|
|
|
The Mecmesin range of digital torque gauges and systems is based upon the AFTI display unit, together with an appropriate `smart` torque sensor and gripping fixture.
|
|
Digital torque gauge : CENTOR W Easy torque gauge with TH senso
Connected to a large range of torque sensors, this CENTOR is a very accurate and solid digital torque gauge.
Most versatile torque gauge : CENTOR W Star with TH sensor
Besides having all the functionalities of the CENTOR W
Easy, the CENTOR W Star torque gauge provides handy further possibilities. It is the most versatile instrument yet designed for all tests in industrial surroundings.
Equipped with the TH sensor, this torque gauge is used to measure low torque levels.
Digital torque gauge : CENTOR W Easy with TW sensor
Using the CENTOR technology, the CENTOR W
Easy digital torque gauges have a very large graphic
display and show a maximum quantity of information
for more efficient measuring.
The Easy torque gauge with TW “wrench” sensor is used to measure high torque levels and when the measurements cannot be made in the axis.
Most versatile torque gauge : CENTOR W Star with TW sensor
Besides having all the functionalities of the CENTOR W
Easy, the CENTOR W Star torque gauge provides
handy further possibilities. It is the most versatile instrument yet designed for all tests in industrial surroundings.
Equipped with the TW sensor, this torque gauge is used to measure high torque levels and when the measurements cannot be made in the axis.
Digital torque gauge "cylindrical" : CENTOR W Easy with TT-sensor
These digital torque gauges have a very large graphic display and show a maximum quantitiy of information for more efficient measuring.
The CENTOR W Easy with "cylindrical" sensor is used to measure torques when the sensor has to be integrated in an assembly.
Basic mechanical torque gauge : UT CM
A basic torque gauge, especially well suited for all measurements of low torque levels in production or in the laboratory.
|
|
- The cell is manufactured in aluminium alloy with HT steel bushes.
- The cell incorporates an eight gauge bridge together with
associated electronics and a 9 volt PP3 non-rechargeable battery.
- Built into the load cell is a large [20mm] 3.5 digit liquid
crystal display mounted on the front of the cell for easy reading
from the operator's position.
- The load cell is self contained and has no external cabling.
- A battery switch is provided on the rear of the cell to prolong
battery life when the cell is out of use.
- All set up and calibration data is retained when switched off.
- The cell is automatically switched off after 15 minutes to
prolong battery life.
- Battery life - typically 50 hours.
|
|
Simple and yet complete, the CENTOR First uses efficient technology to simplify force measurements, in tension and compression.
A big display shows the force measured in tension or compression in the unit selected by the operator: newtons, kilograms or pounds. The bar graph completes the measurement.
The 3 keys make it very easy to use this force gauge and access the essential functions: measurement of the peak tension or compression value, resetting to
zero, and changing the measuring units. It is an ideal tool for basic tests during production. Its metal casing, protected by an elastomer overmould, gives it
exceptional strength.
The internal sensor stands up to an overload of 200% of its maximum capacity.
Simple, precise, robust, supplied with its own carrying case, mains adaptor and certificate, ready for use, it is the basic tool for force measurement.
|
|
FGV-X / FGE-X DART Series
Our workhorse gauge just got better! Faster, smarter, easier to use!
The 1000 series, with its fast 1000 Hz update rate, is able to capture the highest force peaks. With variable display update rate and the same superior accuracy as the DFS series, these new gauges feature unique 180 degree flip displays, permitting the user to read the display right-side up. Additional enhancements are; dual direction keypad, variable baud rate for SPC applications, selectable force direction indication, and selectable power on/off settings.
Designed to ergonomically fit in the palm of your hand, the rugged, all metal construction of the FGE-X and FGV-X permit accurate measurement and display of compression and tension forces up to 100 pounds. (up to 1,000 lbs using the FGV-1000HX)
The FGV-X Dart Series gauges include RS-232c, RS-232 cable, analog outputs, (analog cable is extra) as well as an overload output signal for gauge protection.
|
|
Multi-Measuring System, PHYSIMETER® 906 MC-S/E
The PHYSIMETER® 906 MC-S/E is a universal multi measuring system that, due to its versatility and its modular construction meets all relevant demands of technical measurements. The core of this system is a fully-fledged PC in the size of a credit card. For the first time, integration of different complex technologies in connection with an intelligent system architecture results in an efficient measuring system with intuitive operation. High quality and a clean design underlines the consequent concentration on perfect functionality and ergonomics. Designed as a mobile system the PHYSIMETER® 906 MC S/E is equipped with four channels for simultaneous data-recording of physical values such as force, stroke, pressure as well as the number of revolutions, torque or rotational angles. The versatile amplifier allows the connection of strain gauges, inductive stroke sensors, digital and analogue signals. The connected sensors are automatically identified and can be changed during operation. The strong aluminium housing plus optional force sensor enables the unit to be integrated in a stationary measuring system and is suitable for a load of 1kN.
|
|
It is the force measuring instrument of the electronic formula which can measure both tension and compression power by single axis.
It excels in a response and measured value is displayed in an instant. Since it is a digital instrument, various functions are available. For example, the memory function which can memorize up to 1000 measuring data, comparator function which can program high and low set points. ZP series has USB output function and it becomes easy to connect a computer. Using optional software, it is possible to make precise force-time chart by high speed USB communication. By using with a test stand, it corresponds to a large area from the field of a quality control to the field of research and development.
|
|
Technical Highlights:
- Data Sampling Rate: 1000 Hz
- Accuracy: 0,5 % of Capacity
- Secure Operability due to ergonomically Design
- Overload Protection 200 % of full scale
- Turnable Display automatic direction identification
- Attachable to all SAUTER Test Stands
- Auto-Power-Off
|
|
25.4mm LCD display
Accuracy 0,1% Emax
Shackles included (D150E-12 excluded)
Remote control included
Radio transmission LPD 869,87 MHz (available)
Capacities (Kg.)
1.000, 3.200, 6.500, 12.000
|
|
It is the force measuring instrument of the mechanical type of the power supply needlessness which can measure tension and compression force easily and correctly.
Based on our long history of technical achievement as a force gauge pioneer with the variety of know-how, IMADA mechanical force gauge is produced under advanced technology and severe quality control, and maintain early high precision for a long period of time.
|
|
Real time or Peak Hold Switch to observe transcients or capture peaks by a drag indicator
- Zeroing by a short push of the switch
- Tare Ring for an easy calibration of the tester
- Dual Scale: Shows NEWTON and kg
- Can be mounted on all manual test stands or the optional handle
|
|
MF Series
Incredibly durable and user-friendly, our economical mechanical gauges are excellent for repetitive testing in assembly line or quality control lab applications. The peak mode features an easy push-button reset; this is especially helpful for doing repetitive testing in an assembly line or quality control lab. The real time mode allows you to see force changes as they occur.
Ergonomically designed for handheld use, gauges may be used with the optional handle (great for loads over 15 pounds). Response time is immediate. Large, easy to read dial indicators are designed to reduce gauge parallax.
The MF gauges feature a die-cast aluminum housing. Mounts easily to all Shimpo test stands for even greater control of repetitive testing.
|
|
TesT develops and validates systems, in line with the constantly growing requirements and aim at the needs of its customers to guarantee a complete and competent solution of the highest level. We engage ourselves to reach a high customer satisfaction in a surrounding field of prevention and continuous improvement. The new model 322 is the High end product of most modern measur-ing technique and offers an unusual price performance ratio.
dynamometers integrate a high-resolution force sensor as well as processor-controlled electronics with most modern software, based on a wide experience and the requirements of our customers.
The main area of application for these devices is research and development, production and quality assurance. Particularly operating forces as well as stability of construction and functional units will be measured.
Examples
Springs, switches, levers, fasteners, precision mechanics, foods, cosmetics, vehicles, medical technology, and many more.
|
|
Measuring System PHYSIMETER® 906 MC-B
The measuring system PHYSIMETER® 906 MC-B has been designed for the determination of the mechanical parameters force or torque on the basis of wire strain gauges. The instrument can be supplied with an integrated or an external sensor. For the power supply a block battery of 9 V is required (standard article) or alternatively a plug-in power pack (option). For easy handling the instrument is provided with the functions On/Off, reset and indication of peak value (upper and lower measuring value). In the standard version of the instrument the load introduction takes place at the bottom. Upon request, the load introduction can also be effected on the top of the instrument. The ergonomically designed housing, made of anodised, high-strength aluminium, is provided with threaded bores at the front side so that an unproblematic connection to the ERICHSEN testing machines is guaranteed - as it was also ensured when using the preceding models of the tensile and pressure testing instruments. The instrument is perfectly suitable for mobile as well as for stationary applications.
|
|
|
Radio contact and intreface RS 232, Utmost precision (0.2% of the capac. nominal), recording of the maximum value, endurance battery 200 working hour, posting LCD, warning of overload, indicator charges battery, protection IP 54, coeff of safety 500% of the CMU.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category
