|
|
novel conception with very few moving parts
selfcontained compact construction with moving parts inside
in spite of selfcontained construction easy to service
preserving main cable due to 4 big guiding pulleys
preserving pulling cable thanks to increased size of the lifting pulley
tag-line in preparation
smooth passing across supports due to 4 guiding pulleys
passing across big and small WYSSEN saddles
whole construction made of high tensile steel
over years proved cable drop out protection device, externally placed, therefore fast changeable
drop out protection device made of crome-molybdanium steel, allowing fast travelling across saddles
big swinging angle of pendulum
main cable preserving clamping chuck thanks to special clamping grove
serial cable breakdown safety device
stilted construction, allowing to dismantle the chassis into small exchangeable parts
|
|
Wireless switching
For moving over short distances with load docked
Advantages:
Precise clamping and release at the touch of a button
Hooks swings out for clamping during slow descent
Does not have to be raised when clamping during slow descent even with load
Remote control integrated into radiotelephone
Can be retrofitted to any HY-3
Hydraulic time release remains active if wireless Communication is interrupted
Protected against clamping if travelling too fast
|
|
The basic carriage for
the gravity system is
controlled electrohydraulically
and
equipped with an
alternator for battery
power supply.
Optional components:
• Radio control
• Expansion to
3-cable system with
mainline slack
pulling device and
haulback-line drum.
|
|
USKA-1,5 uphill and downhill
Radio controlled with mainline clamp
Skyline clamp is controlled by radio
Skyline clamp and Mainline clamp switches contrarily
Emergency clamp during the run is possible
Load attitude trough mainline clamp
Advantages:
The position of the carriage can be changed easily, a special advantage in thinning operation to avoid damages in the culture during lateral skidding
Logs can be lowered just outside the landing area and pulled into the landing in a dragging position
Load capacity: 1500 kg
Weight : 285 kg
|
|
SKA-1 uphill
Carriage cycling system
Skyline clamp and loadhook
Skyline clamping and loadhook release by reversing the direction of carriage travel
Load capacity: 1500 kg
Weight : 150 kg
Skyline: Ø12mm - Ø22mm
Mainline : Ø8mm - Ø11mm
|
|
SKA-2,5 uphill
Carriage cycling system
Skyline clamp and loadhook
Skyline clamping and loadhook release by reversing the direction of carriage travel
Load capacity: 2500 kg
Weight : 290kg
Skyline: Ø18mm - Ø28mm
Mainline : Ø10mm - Ø14mm
|
|
GSK 80
# max. payload:
8 t (2 x 4 t)
# max. lifting height:
290 m ( Details)
# Engine:
Hatz Diesel engine 42 KW (57 PS), air-cooled
# Stroke hoist:
electro-hydraulic
# Control:
remote controller
To get more information, please download the GSK 80 datasheet.
GSK 80 was used at the hydro-electric power plant St. Anton, Austria Read more...
|
|
MSK-10 Slackpulling carriage
Range of application
Uphill logging
Engine
Dieselengine Hatz with 7,3kW (10 HP)
Control mode
with 2 Hand-held radio transmitter
Load capacity
Corresponding to the used lines
Weight
ready 590 kg
Slackpulling power
up to 250 kg
|
|
MSK-3 Slackpulling carriage
Range of application
for up- and downhill logging and for flat terrain
Engine
Dieselengine Hatz with 5,6kW (7,5 HP)
Control mode
with 2 Hand-held radio transmitter
Load capacity
30kN (3t), but corresponding to the used lines
Weight
ready 680 kg
Slackpulling power
up to 620 kg
|
|
|
This special carriage, specially developed for building yards, is used for the transport of extremely weight loads. With a lifting force of 10t in single traction and 20t in double traction, the SF100/200 can speak for himself. This carriage can be mounted on a single or double way of skyline rope.
|
|
This Seik cable crane SF 20/40 is exspecially suitable for forestry and for use on smaller construction sites. The SF 30/60 is intended for larger construction sites.
It allows :
- precise and rapid working even with heavy loads.
- The winch can be placed in any positionbetween hilltop and valley.
- No secondary carrier is necessary for double traction.
|
|
The SFM20/40 sliding cable crane is the ideal solution for forestry (turret and bi-directional use) as well as for small construction sites.
It offers the following advantages:
- Lightweight yet sturdy
- Rapid and precise operating even with just two people
- Fit also for oblique pull and steep areas
- The winch can be placed freely either uphill or downhill
- The shifting of the trolley along the carrier cable is always possible
- Orderly unloading of trunks
- No other trolley necessary for double pull
|
|
This auxiliary non-motorized carriage was developed to carry loads long especially on building yard. Coupled with a cart SEIK SFM 30/60 and a special lifting beam, was able to lift up to 12t in quadruple traction and 9t in triple traction triple. This particular carriage has a weight of 450kg.
You can connect up to 2 auxiliary carriages and a SFM 30/60, making a sixth traction, you can lift up to 18t.
Advantages:
- The load can be long and heavy;
- Stable against the wind with the long lifting beam;
- With a relative cost, the SFM 30/60 can be prepared in order to lift up to 18T
|
|
|
|
|
|
This electric carriage is used to move small loads (up to about 400kg) in places not viable, where it is not advantageous building a stationary cable crane.
Following the idea of a cable crane in which the power and control signals are integrated into the traction cable, it was possible to develop a simple, lightweight and low cost carriage.
Is used an electric winch as traction element, which moves the carriage along the line.
The carriage is equipped with an electric motor, which moves the lifting hook. This engine is placed on the machine and is powered by the batteries on board. The batteries are recharged via an electronic charger positioned in the control cabinet, near the traction winch. By exploiting the conductivity of the traction cable can transmit the load from electrical cabinet up to the carriage batteries.
The cable crane is controlled by a transmitter. The receiver is mounted on the machine, which communicates with the electrical panel through conductors within the traction cable.
|
|
The patented system of carriage with double hoisting winch.
This additional motorized carriage has been specially developed for forestry applications, but it can also be used on building yards, such as for the transport of long tubes. The hydraulic winch of the NL 20/40 is powered by the hydraulic circuit of the main carriage SFM 20/40 or SFM 30/60.
Through the transmitter is possible to control both drives simultaneously lifting in a synchronized, or even individually.
The force lifting the NL 20/40 is 2t in single traction and 4t in double traction, with the optional lifting beam.
Advantages:
· Height of the skyline rope contained, and consequently reduced height of supports;
· Increased speed of the carriage in full load;
· economic work.
|
|
Dalmec has already manufactured more than 4000 Manipulators for the car industry, solving the handling problem of:
Axles Gears
Batteries Tailgates
Bottles Bonnets
Headlinings Pedal assembles
Clutch assemblies Radiators
Drive shafts Rear seats
Cylinder heads Side members
Dashboards Body sides
Doors Sunroofs
Engine frames Spare wheels
Engines Steering columns
Exhaust pipes Suspensions
Floor panels Fuel tanks
Flywheels Wheel assemblies
Front seats Wheels
Frontal parts Windscreens
|
|
The most advanced manipulator
A rigid manipulation principle is often desirable for eccentric handling (loads that can be handled centrically are best manipulated using a flexible or self-suspended principle such as a cable balancer). The most advanced possibility in rigid handling systems is the Master Balancer: because, in this case too, the arms are bare and hollow. So that manoeuvrability is much better than with conventional manipulators which have drive elements and sometimes even ballast weights on the arms, which means that everything moves. (For technical specifications: see table below)
|
|
Pneumatic rope balancers for all types of handling, “weightless”, which allows the minimum effort for the operator for different kinds of parts.
Max capacity 110 kg
Max work radius 7 m
On customer request the following can be supplied:
· Fork liftable self bearing base
· Special handling attachments: mechanical, pneumatic, vacuum o magnetic operated
· Manual or pneumatic rotating or tilting devices
· Jib cranes or light crane bridge or monorails systems, complete with metal supporting frame, delivered as a turn key project
|
|
|
|
|
|
HANDLE YOUR PRODUCTS INTUITIVELY WITH ZE'SOLUTION SAPELEM
ECONOMICIAL
Electric energy.
Eliminate MSD.
INTUTIVE
Follow operators' nature gestures.
No bouton necessary to make movements.
No adjustment necessary to adapt mass changes.
REACTIVE
Reaction time < 0,1 s.
Acceleration up to 1 g.
Max Speed 2 m/s.
POWERFUL
From 0 until 300 kg.
Arm up to 4,7 m.
PRECISE
At Millimeter.
Arm in aluminium : Movements without resistance.
SECURE
Detector of hand presence.
Active security through embedded software.
Power-Cut Management.
ERGONOMIC
Ergo Conception : lightness, sensibility, visibility …
Design for left and right handers.
Effort to make movements < 20 grammes.
ALL PRODUCTS
Cans, boxes, bags, doors, windshields, bumpers, tanks, tubes, bottles, pallets, tyres, ham, spools, eggs, motor parts (water pump, etc.), metallic systems, windows, dashboards, sand core, equipments, moulds, parts of fuselage, yoghurt pots, exhaust system, car batteries, shower trays, sinks, sunroofs, motorbikes engines, bus windscreen, car doors, bonnets, steel cabinets, car seats, aeronautical parts …
ALL FIELDS
Food industry, aeronautics, car industry, textile, cardboard, glass, woodworking, plastic, chemistry, sheet metal, medical, warehouses, electronics, equipments, pharmacy ...
|
|
All solutions FAMATEC are programmed to be prepared in these various configurations, while guaranteeing moreover, the possibility of reconfiguring the solution thereafter during an evolution or of a change of the requirements of the Customer.
The suspended configuration adapts to mediums characterized by a place of limited operation in which there is a need for working under good conditions and in perfect safety
|
|
an Intelligent Assist device for lifting and moving car seats with no efforts. Designed to suit all ergonomics criteria and to comply with all the most recent EU regulations regarding prevention of risk from load handling and prevention of carpal tunnel syndrome.
No production stops due to operator absence for back injury, consistent productivity throughout the day as well as the year. Precise positioning of the seat even in a restricted area thanks to the great sensitivity of the electronic system which respond immediately to the operator force upwards/downwards.
|
|
| ... products without technical information |
| |
|
Car body hoist, admissible load 8 t / 7 t (BGV D8) and car body jack, admissible load 8 t / 5 t (VBG 14) for workshops: - low speed and high speed gear for quick and easy lifting - self-locking spindle for highest security - double safety nut (VBG 14) allows working under jacked-up load - big and solid ground plate for safe standing - adjustable claws (4 postions) for time saving height adjustment - rubber tyres for quick and easy use
|
|
GH - Low profile trolley jacks
Reliability. All NIKE trolley jacks feature modern design and are designed to incorporate large safety margins. A safety valve on all models protects against overloading.
Service. Easily replaceable components make NIKE trolley jacks simple to service. We have a large network of dealers and service agents around the world.
GH - models
• High-lift design for good accessibility.
• Protector, top saddle protection for safer lifting.
• Polyamid wheels - for quieter positioning.
GHP2 - can be operated manually or using compressed air (0,8 - 1,4 MPa)
|
|
| ... products without technical information |
| |
Amiral Speed dry eco plus
Curing time is halved and energy consumption cut to 50% in cold water conditions.
|
|
| ... products without technical information |
| |
|
The Mini-Vert is a compact battery powered welding travel carriage. It is held on the workpiece with strong permanent magnets. The Mini-Vert travels and carries a welding gun in flat or vertical positions producing continuous uniform fillet welds.
|
|
The Kat® Carriage / Compact Oscillator combines the Gullco Kat® all-position travel carriage with a compact oscillator head and its controls. Mounting brackets, connecting cable, and MIG gun holder are included. Micro-fine vertical and horizontal adjustment is accomplished using Gullco rack boxes and rack arms are also included with the package.
The Kat® Carriage / Compact Oscillator is designed to increase production and improve the quality of the weld produced in automatic mechanized welding operations by minimizing weld defects such as poor penetration, incomplete fusion, overlap and undercut.
The oscillator provides a pendulum, tangential or step (square pattern) motion to the welding gun. Stroke width is adjustable. Stroke speed, dwell times (left, center, and right), wire feed start delay, carriage start and stop are all set on the oscillator control and come built into the travel carriage and can also be provided as a remote pendant.
|
|
|
|
see the results for the following category : 
