|
|
Framax is the framed formwork system that achieves a continuous 15 cm grid with no more than a small number of panels, upright or on their sides.
All connectors and all accessories fit seamlessly into the grid – for short forming times and high cost efficiency.
|
|
MANTO
Large-frame formwork
Quality, functionality and flexibility are the decisive factors for a formwork system. MANTO exhibits all three to a high degree and is therefore one of the most frequently used formwork systems in industrial construction and housing projects.
|
|
Circular columns are above all required in structural and civil engineering projects.
In skeleton constructions, entrance halls etc. circular columns are a special architectural feature. A second area of application are underground car parks, water basins and bridge piers.
Almost always a perfect concrete finish is required, since finishing works are virtually never carried out on these columns
|
|
MGC/MGS - Guided Climbing / Screens
MGC: Climbing Higher, Climbing Safer
MEVA´s Guided Climbing System MGC comprises vertical formwork and safety platforms as a single unit. It remains securely attached to the building structure during building and lifting. Thus, wind velocities do not affect the building process. Assembly is at ground level for improved safety and speed.
The MGC system is designed to meet the highest standards in effi ciency and safety:
for high-rise construction
complementing the proven climbing scaffold MEVA KLK
The Guided Screens System MGS
is the MGC´s twin system for slabs. Highest safety is guaranteed by full side protection, enhanced by several technical advantages:
spacing of brackets is variable
level heights 3,00 m to 4,25 m
secondary platforms attachable to any bracket
integrated access system
MGS is also assembled at ground level: All parts are lifted into the guard rails from below
|
|
The column formwork Caro- Falt consists of four identical panels with articulated links which are assembled like a windmill. The CaroFalt can be used with or without triangular strips to form either sharp or smooth edges.
Adjustment of column section
Thanks to the perforated rail it is easy and fast to adapt the column section from 20 cm to 60 cm in increments of 5 cm – square or rectangular.
|
|
Proping Megashore aluminum
Aluminum proping is a system entirely flexible and adaptable to all the configurations. This product is ideal to take again important loads going up to 100 kN for some 0,50 m heights to 15 m and more.
It is composed of 4 principal elements: stays, spillplates, jacks of stays and frameworks of wind-bracing.
The stays are light and couplables between them. Their adjustment is simple and fast. They can-being assembled via frameworks of 8 different sizes.
According to the application, this system perhaps compatible with the beams Titan T (see heading COFFRAGE>COFFRAGE HORIZONTAL>Les beams out of aluminum TITAN T).
It also supplements the two systems of horizontal formwork traditional HV (of the primary beams assembled with the secondary aluminum beams and of the primary beams assembled with the famous panels Combi HV) in the case of casting with great height or of very thick flagstones.
|
|
Triplex R
is a brace for wall heights of more than 6.00 m, provided with a formwork connector and a foot plate.
Triplex SB
is an additional static support for high single-sided formwork (> 6.00 m) when support frames STB 450 and height extensions 150 are used.
|
|
Aluminum beams TITAN T
The aluminum beams TITAN T are used for the formwork of concrete slabs and for the proping of prédalles.
With these beams, you exploit to the maximum the advantages of aluminum.
They are light and resistant.
Advantages of the system
The beams TITAN T have an extreme longevity compared to wood
No cutting on the building site
Insensitivity to the falls and the bad weather
Clouability
The quantity of unusable beams at the end of the building site is lower than 1%.
Beam TITAN an aluminum weighs approximately half of a beam out of of the same wooden length
The team works more quickly for the formwork and the dismantling
At the end of the lifetime, the beam aluminum preserves a still high residual value, aluminum is a metal easily which can be recycled, which is not the case of the beams out of wooden
Not need for crane
Applications
Formwork of flagstones
Proping of prédalles
Formwork of beams (with the executives TITAN U)
|
|
The geometry of the building will determine your choice. Call our specialists - and they will make an economical proposal.
Standard table forms
are available in two sizes::
2.50 x 4.00 m and 2.50 x 5.00 m;
pre-assembled units; supplied ex stock.
This simplifies the handling on the jobsite.
|
|
VARIOMAX
Timber beam formwork
VARIOMAX is a modern timber beam system enabling you to realize any kind of soffit – any ground plan, slab size and slab thickness – with ease. All the VARIOMAX parts are distinguished by their superlative quality and high functionality. Timber beams, props and formwork panels form a perfect line-up helping you to effortlessly master any challenge.
|
|
MevaDec: drop head-beam-panel-method
As with the primary-and-secondary-beam-method the support system consists of primary beams and drop heads. It supports the ready-made panels. The patented drop head permits the early striking of primary beams and panels. This method is especially suited for ground plans with great dimensions.
|
|
|
Mammut is the strong and sturdy modular formwork system for big and medium-sized contractors who are involved in industrial and civil engineering projects as well as in the construction of administration and residential buildings.
|
|
The Modular System for Engineering Structures
PERI engineers have created ideal project and connecting method combinations from known tunnel, bridge and construction engineering load combinations, and developed this to form a versatile construction kit. This means load-optimized and geometrically-adapted supporting formwork can be built from a large selection of system components.
VARIOKIT, the engineering construction kit with rentable, standardized components, is the solution for numerous requirements in civil engineering:
- fast
- safe
- cost-effective
In the process, PERI provides technical information for each project e.g. operating instructions and assembly drawings. Static calculations and assembly support are also integral elements such as the constant support given to contractors and help provided with new tasks for current projects. For all construction projects, PERI can provide everything from one source.
|
|
Coffrage CTR 3010
SAFETY All the accessories of safety are integrated into the panel including protection front face. Extensible railing for an optimal safety casing Sheet QUALITY ép. the 5 mm for best finished fast concrete vertical Assembly and of high degree of accuracy. Rigid ROBUSTNESS Framework with vertical stays out of V with 2 levels of spacers One more: its use with concrete car placing. SIMPLICITY Accessories entirely colisables Level of passage ergonomic spacers Only one assembly tool. The RANGE Panels HT 3,00 m Under rise HT 1,50 m Under rise HT 1,00 m Spillplates HT 0,50 m
|
|
The girder is a central component for slab and wall formwork systems and choosing the right one is crucial in achieving the highest possible level of cost-effectiveness. The decisive factors are the durability and handling costs - not the original investment.
Through the high load-bearing capacity and rigidity of the GT 24 compared to other 20-cm high formwork girders, fewer girders, steel walers or props are required for both wall and slab formwork.
Due to the high proportion of synthetic resin in the high-grade timber web, the PERI VT girder is able to maintain its high level of dimensional stability and robustness. Steel caps, secured with side-to-side rivets, provide strong impact and edge protection and extend the service life of the girder.
The VT 20K has been specially developed for use with slab formwork, and is the low-price option for thinner slabs.
|
|
PERI SKYDECK
The Tested Panelized Slab Formwork System for Slab Thicknesses up to 95 cm
SKYDECK with drophead system
Striking can be carried out after only one day (depending on the slab thickness and strength of concrete). The panels are easier to detach from the concrete, materials handling is accelerated, and the qunatity of materials is reduced.
Less cleaning means shorter shuttering times
This is possible due to the plastic rack, powder coating and the special design. The SKYDECK main beams lie protected under the panels. The panel as well as the main beams have integrated self-draining edges. The edges of the panels are also undercut which keeps cleaning to a minimum.
|
|
The SC 9015 Panel
A new panel proud of its predecessors!
The SC 9015 panels are compatible with the entire SATECO range (even circular formworks). Accessories compatible with SC 9010 II panels.
|
|
|
|
|
|
The MAXIMO panel formwork succeeds in minimizing imperfections in the concrete finish and creates a neat joint and tie arrangement.
By means of a newly developed conical tie system, the wall formwork system does not require any spacer tubes and work takes place from only one side. This means maximum reductions in expense and considerable savings of time and resources.
Apart from the advantages of a panel formwork regarding flexibility and fast shuttering times, MAXIMO opens up new possibilities of fashioning visible concrete surfaces through a particular arrangement of individual elements. The uniform tie arrangement continues to underline the very achievable results even more.
Advantages
1. Centrally-positioned tie point:
The systematics of the central tie point require that all anchor positions must be filled. This avoids any errors during shuttering and, among other things, plugging of those tie points not actually being used no longer applies. Plugged tie holes are thus a thing of the past.
2. Ties installed from one side:
Through the use of specially-designed ties, a worker on the opposite side is not required as well as conventional tie sleeves no longer being necessary.
3. Neat joint and tie arrangement:
Apart from the flexibility of a panel formwork, PERI MAXIMO provides the possibility of designing visible concrete surfaces by a skilful arrangement of individual elements. In addition, the uniform tie pattern highlights the finish even more.
|
|
PERI TRIO
The Most Successful Panelized Wall Formwork System Worldwide
High labour costs on construction sites increasingly require easier and faster formwork systems.
The number of components to be moved determines the shuttering times and thus the costs of construction. TRIO elements need one and the same coupler for all connections which means a time-consuming search for the correct part is avoided.
PERI engineers placed great importance during the development of the TRIO system to reducing shuttering time. TRIO is a versatile formwork system with few components, which meets and exceeds the demands of the job site in a simple way.
|
|
|
|
|
|
Post Wings of Mill: A design multi-sections for a multifunction tool.
VERSATILITY
Design of brackets of bolted reinforcement
0.50 m heights to 9.80 m per superposition of the various elements
SAFETY
Stabilization with the wind ensured by stabilizers various heights according to the configurations
QUALITY
No the hole in sheet metal casing for a better quality of the facing
Seal of sealing incorporated in the panel
Option
Articulations between the 2 half-shells, wheels of translation for an handling of the post.
A tool allowing to carry out all sections of the square or rectangular posts to the step of 2.5 cm:
TYPE 700: of 0.10 X 0.10 m with 0.625 X 0.625 m
TYPE 700 and 1075: of 0.10 X 0.475 m with 0.625 X 1.00 m
TYPE 1075: of 0.475 X 0.475 m with 1.00 X 1.00 m
TYPE 875: of 0.175 X 0.175 m with 0.80 X 0.80 m
The formwork post is designed containing 2 principal elements:
1 - Panels casing out of sheet metal ép. 4 mm
2 - Brackets of reinforcement with adjusting device of squaring
Each post consists of 4 panels assembled in two "half-shells" via brackets.
The 2 "half-shells" are assembled between them by screws and nuts with fast step, unlosable.
|
|
Foldable scaffold system Multip for safe working places consisting of platforms with guard rails and access hatches assembled at the formwork also during transport.
* Formwork and working platform can be transported already assembled
* Repeated assembly of a number of many individual brackets, platforms and guard rails is no longer necessary
* Time profit by folding mechanism
* Safe and accordingly quicker operation with all system components
* Very much longer service life than traditional timber decking
* Purchase of timber for decking and guard rail is no longer necessary
* All safety at work directives are complied with
Technical Data
Design Load: 2,0 kN/m²
Platform width: 72 cm - Logo and Athlete
85 cm - Trapezoidal Girder Formwork
Platform length: 135 - 240 cm - Logo and Athlete
238 cm (ext.), 210 cm (int.)
from Diameter 7,00 m
|
|
|
Doka folding platforms K are pre-assembled, ready-to-use scaffold platforms with standardised system components for all construction jobs, compliant with both EN 12811-1 for working platforms and DIN 4420 for protection platforms.
|
|
P3D Platform Increased Safety
Compliant with standrad NFP 93.351
Automatic locking of the lower parts of the platform
Fixing with secured pegs
Bracing of panels up to 8.50m
|
|
| ... products without technical information |
| |
|
|
see the results for the following category :