|
|
| ... products without technical information |
| |
... see all the products in the category
Fuel cells
|
| Following the state-of-the-art trend in automation for decentralized systems without cabinets MTM Power has designed the new series PM-IP67A with 50, 75, 100, 150 and 200 W. Remarkable feature of the primary switched modules is that they are suitable for applications with protection degree IP67 for different tasks in indoor and outdoor industrial applications. Without any additional protection against harsh environmental conditions these power supplies can be mounted and used just at the place where needed. The compact power supplies with AC and DC wide input range are designed for worldwide use and are available with single and dual outputs of 5, 12, 15, 24, 36, 48, ±12, ±24, ±36, ±48 and 12/24 VDC. Their dimensions are 166,0 x 85,0 x 35,0 mm and they are connected via 7/8" connectors. The devices are vacuum encapsulated, acc. to Protection Class 2 and comply with the Low Voltage Directives as well as with the up-to-date EMC Standards as regards CE Conformity. Further features are rugged design, SMD-technology, automatic 100 % final test and 100-%-burn-in-test. The series PM-IP67A is short circuit protected, needs no ground load and is operating within a temperature range of -40 to 75 °C. |
|
The TEX-120 series is a range of sealed fieldpower supplies for applications in
harsh outdoor environment. The die-cast aluminium case is water-(incl. salt water), ice, dust and oil resistant to IP67 and NEMA4X requirements.
The construction is shock and vibration proof.The operating temperature range
is specified from -40°C to +85°C without any derating.
There are 2 models available with regulated 12VDC/8A and with 24VDC/5A output. The power supplies feature universal 90 to 264Vac input range and
have safety approvals including CB scheme, IEC/UL 60950-1 and UL 508.
The product is also certified to ATEX94/9/EC for class l, div.ll applications in
hazardous locations. |
|
| Factorized Power Architecture maximizes a power system by providing a high degree of system flexibility, superior power density, efficiency, transient response, and reliability. This new architecture is enabled by V-I Chip components: the BCM intermediate bus converter, the PRM non-isolated regulator, and the VTM current multiplier. These families of integrated power components provide new ways to create small, cost-effective, high-performance power system solutions. |
|
Specifications:
Power:
Input voltage range: 90 - 264 VAC
Output voltage:
+5VDC @ 2A,
-5VDC @0.2 A,
12VDC @1 A,
-12 VDC @ 0.3 A
Input frequency: 47 - 63 Hz
Inrush current cold: 20 A @ 110 VAC, 40A @ 220 VAC
Hold-up time: 16 ms
Raise time: 500 ms
Overload protection: power limit
Short protection: auto- Recovery
MOSFET design
Built-in line filter
Meets FCC, CE, TUV
Meets UL478 and CS
Fast type FUSE 2A/250V
Bus Interface PC/104 Standard Compliant
Connector
3-pin AC input
6-pin DC output
Dimensions 90(L)x96(W)mm (3.54" x 3.78")
Weight 120g
Operating Temperature 0°C ~ 60°C |
|
| ... products without technical information |
| |
Advantage Lincoln
• Independent arcs. Starting or stopping one Multi-Weld doesn't affect the welding of the others.
• The Multi-Weld 350 is capable of continuous operation at 350 amps in 122°F (50°C) air temperature.
• No control cables are needed. Single weld cable output from the power source to one or several Multi-Weld 350s.
• Controls are located close to the operator for quick access.
• High efficiency design uses less than half the power of other grid systems.
• Lincoln Chopper Technology™ for quality welds with instant control of the arc for superior welding results.
• Constant voltage (CV) for MIG or flux-cored wire welding.
• Constant current (CC) for stick welding or arc gouging.
• Additional stick welding controls include hot start, arc force, electrode type selection (E7018 and E6010).
• Arc gouging capability with a single Multi-Weld 350 and up to 5/16" (8.0mm) electrode, or with paralleled units for up to 700 amps of power using a 3/8" (9.5mm) electrode.
• Manufactured under a quality system certified to ISO 9001 requirements and ISO 14001 environmental standards.
• Three-year warranty on parts and labor. |
|
| ... products without technical information |
| |
When it has been decided that a central battery system is the most suitable system of emergency lighting for a particular site, the designer needs to give consideration to the following:
- Lighting design
- Type of system
- System control & mode of operation
- Battery type
- System sizing
- Battery room ventilation
More informations available: |
|
| Unitek Peco's Dual Pulse Series is a full range of Capacitive Discharge (CD) power supplies for precision resistance welding applications. Their unique "Dual Pulse" function overcomes process variables; part and electrode surface inconsistencies contribute to poor welds. Plating irregularities or contaminants, including oxides and oils, affect weld reliability. The “Dual Pulse” function virtually eliminates these problematic variables. |
|
|
|
