|
|
|
|
|
|
Powerbox Greenhub 1000
Line GreenHub di Powerbox H2planet, that is all the one which you have always asked from an independent energetic system:
like the current of house but with all the advantages of energetic independence. Ideal like group of continuity, unit of emergency generation, unit of generation from field, but also like domestic generator for the isolated rooms with lowlands every day requirements.
Technical detailed lists
- till 1000W of peaking power
- the maximum power in continuous use: 800W
- exited in alternating current BTicino 220V (sinusoidal pure)
- the maximum hydrogen consumption
- feeding 2-6bar
- hydrogen: degree 4,5 minimum (gas dry)
- hydrogen consumption to max power: 14 l/min.
Included in the system Powerbox GreenHub 1000:
- it arranges with car-humidification system stack (NOT PRODUCED REFUSE)
- handles in rubber for the transport
- possible recovery arranges of GreenAir aeration for maximum performances stack and warm air for cogenerativo use
- holes threaded posterior for the wall implantation
- attack ultrasure express to lowland pressure
- shop for approached express inner
- timer programmabile for programs ignition weeklies magazine/standy
- inverter integrated DC/AC and DC/DC
- escape 220-230VAC @ 50Hz
- escape 12/24VDC for recharges batteries
- escape 5V USB 2,0 for all the electronics
- emergency sensors standard: losses hydrogen, inner temperature, pressure for control level hydrogen, antiscassinamento
Optional:
- remote control iGreen GSM/GPRS smartphone/iPhone over IP
- slowly of substitution to by-wire (iGreen necessary) of hydrogen bottles
- programmed maintenance
|
|
|
|
|
|
Powercell Greenhub 3000
Line GreenHub di Powerbox H2planet, that is all the one which you have always asked from an independent energetic system:
like the current of house but with all the advantages of energetic independence. Ideal like group of continuity, unit of emergency generation, unit of generation from field, but also like domestic generator for the isolated rooms with lowlands every day requirements.
Technical detailed lists
- till 3000W of peaking power
- the maximum power in continuous use: 2700W
- exited in alternating current BTicino 220V (sinusoidal pure)
- the maximum hydrogen consumption
- feeding 2-6bar
- hydrogen: degree 4,5 minimum (gas dry)
- hydrogen consumption to max power: 42 l/min.
Included in the system Powercell GreenHub 3000:
- it arranges with car-humidification system stack (NOT PRODUCED REFUSE)
- handles in rubber for the transport
- possible recovery arranges of GreenAir aeration for maximum performances stack and warm air for cogenerativo use
- holes threaded posterior for the wall implantation
- attack ultrasure express to lowland pressure
- shop for approached express inner
- timer programmabile for programs ignition weeklies magazine/standy
- inverter integrated DC/AC and DC/DC
- escape 220-230VAC @ 50Hz
- escape 12/24VDC for recharges batteries
- escape 5V USB 2,0 for all the electronics
- emergency sensors standard: losses hydrogen, inner temperature, pressure for control level hydrogen, antiscassinamento
Optional:
- remote control iGreen GSM/GPRS smartphone/iPhone over IP
- slowly of substitution to by-wire (iGreen necessary) of hydrogen bottles
- programmed maintenance
|
|
|
|
|
|
Powercell Greenhub 4000
Line GreenHub di Powerbox H2planet, that is all the one which you have always asked from an independent energetic system:
like the current of house but with all the advantages of energetic independence. Ideal like group of continuity, unit of emergency generation, unit of generation from field, but also like domestic generator for the isolated rooms with lowlands every day requirements.
Technical detailed lists
- till 4000W of peaking power
- the maximum power in continuous use: 3800W
- exited in alternating current BTicino 220V (sinusoidal pure)
- the maximum hydrogen consumption
- feeding 2-6bar
- hydrogen: degree 4,5 minimum (gas dry)
- hydrogen consumption to max power: 56 l/min.
Included in the system Powerbox GreenHub 4000:
- it arranges with car-humidification system stack (NOT PRODUCED REFUSE)
- handles in rubber for the transport
- possible recovery arranges of GreenAir aeration for maximum performances stack and warm air for cogenerativo use
- holes threaded posterior for the wall implantation
- attack ultrasure express to lowland pressure
- shop for approached express inner
- timer programmabile for programs ignition weeklies magazine/standy
- inverter integrated DC/AC and DC/DC
- escape 220-230VAC @ 50Hz
- escape 12/24VDC for recharges batteries
- escape 5V USB 2,0 for all the electronics
- emergency sensors standard: losses hydrogen, inner temperature, pressure for control level hydrogen, antiscassinamento
Optional:
- remote control iGreen GSM/GPRS smartphone/iPhone over IP
- slowly of substitution to by-wire (iGreen necessary) of hydrogen bottles
- programmed maintenance
|
|
|
|
|
|
Powerbox Greenhub 2000
Line GreenHub di Powerbox H2planet, that is all the one which you have always asked from an independent energetic system:
like the current of house but with all the advantages of energetic independence. Ideal like group of continuity, unit of emergency generation, unit of generation from field, but also like domestic generator for the isolated rooms with lowlands every day requirements.
Technical detailed lists
- till 2000W of peaking power
- the maximum power in continuous use: 1800W
- exited in alternating current BTicino 220V (sinusoidal pure)
- the maximum hydrogen consumption
- feeding 2-6bar
- hydrogen: degree 4,5 minimum (gas dry)
- hydrogen consumption to max power: 28 l/min.
Included in the system Powerbox GreenHub 2000:
- it arranges with car-humidification system stack (NOT PRODUCED REFUSE)
- handles in rubber for the transport
- possible recovery arranges of GreenAir aeration for maximum performances stack and warm air for cogenerativo use
- holes threaded posterior for the wall implantation
- attack ultrasure express to lowland pressure
- shop for approached express inner
- timer programmabile for programs ignition weeklies magazine/standy
- inverter integrated DC/AC and DC/DC
- escape 220-230VAC @ 50Hz
- escape 12/24VDC for recharges batteries
- escape 5V USB 2,0 for all the electronics
- emergency sensors standard: losses hydrogen, inner temperature, pressure for control level hydrogen, antiscassinamento
Optional:
- remote control iGreen GSM/GPRS smartphone/iPhone over IP
- slowly of substitution to by-wire (iGreen necessary) of hydrogen bottles
- programmed maintenance
|
|
|
|
|
|
Powercell Greenhub 5000
Line GreenHub di Powerbox H2planet, that is all the one which you have always asked from an independent energetic system:
like the current of house but with all the advantages of energetic independence. Ideal like group of continuity, unit of emergency generation, unit of generation from field, but also like domestic generator for the isolated rooms with lowlands every day requirements.
Technical detailed lists
- till 5000W of peaking power
- the maximum power in continuous use: 2700W
- exited in alternating current BTicino 220V (sinusoidal pure)
- the maximum hydrogen consumption
- feeding 2-6bar
- hydrogen: degree 4,5 minimum (gas dry)
- hydrogen consumption to max power: 70 l/min.
Included in the system Powerbox GreenHub 5000:
- it arranges with car-humidification system stack (NOT PRODUCED REFUSE)
- handles in rubber for the transport
- possible recovery arranges of GreenAir aeration for maximum performances stack and warm air for cogenerativo use
- holes threaded posterior for the wall implantation
- attack ultrasure express to lowland pressure
- shop for approached express inner
- timer programmabile for programs ignition weeklies magazine/standy
- inverter integrated DC/AC and DC/DC
- escape 220-230VAC @ 50Hz
- escape 12/24VDC for recharges batteries
- escape 5V USB 2,0 for all the electronics
- emergency sensors standard: losses hydrogen, inner temperature, pressure for control level hydrogen, antiscassinamento
Optional:
- remote control iGreen GSM/GPRS smartphone/iPhone over IP
- slowly of substitution to by-wire (iGreen necessary) of hydrogen bottles
- programmed maintenance
|
|
|
Powerbox 500 is a fuel-cell system for electric current production at zero emissions. A super-compact500W system (550W peak), ideal for fuel-cell small applications: modeling, robotics, automation, small electric vehicles or any other portable application.
|
|
|
Rugged. Reliable. GenCore® fuel cell systems. With unmatched availability and scalable DC power, GenCore fuel cells outperform batteries and generators without any of the associated drawbacks. It’s the best solution for your back-up power requirements. Because you don’t want to know when the power comes back on, you only want to know that it never went out.
|
|
... see all the products in the category
Fuel cells
|
GENERAL SPECIFICATIONS
/- 1% Steady State Accuracy over a 10:1 Turndown (w/constant speed drive)
Continuous Duty / Severe Service Design
Polar Crank Drive Design
Rugged Cast Iron Gear Housing
Modular Design
Multiplex Capability
Variable Stroke Length (non-last motion)
Integral Pressure Lubrication System
Double Ball Check Valves
Pressures up to 10,000 psig (690 bar g)
Flows up to 1,225 gph (4,637 lph)
Meets API Standard 675
|
|
|
|
|
|
Piston pumps are precise and – compared to diaphragm dosing pumps – almost pressure-independent metering units. The flow rate changes in proportion to the stroke length and can thus be adjusted to very small values. Fields of application are – among others – process engineering and chemical processes, i.e.: wherever the medium must be metered precisely.
The FEDOS E / DX piston dosing pumps from Lutz-Jesco are available at flow rates between 0.17 and 31.5 l/h, with or without microprocessor control. Depending on the size of the pump, maximum pressures between 30 and 200 bar are admissible.
If no control is required for constant metering, the motor is connected directly to the terminal box. In this case, FEDOS E pumps are used. To change the flow rate, either the stroke length can be adjusted mechanically, or the speed of the motor is controlled by means of a separate frequency converter.
FEDOS DX pumps are used if an integration in controls or automatic control systems is requested.
FEDOS DX pumps allow the adaption to a large number of different control systems and system monitoring equipment. The signals required for the external avtivation of the pump can be simple voltage-free closing contacts from water meters or controllers or analog 0(4)...20 mA signals.
|
|
Pulseless series is designed to be almost nothing of any pulsation with high accuracy by special cam and check valves.
Compact design achieved by the cylindrical cam which drives two plungers.
|
|
|
FMI pumps are modular in design.The Pump Head Modules can be easily removed for cleaning or replaced with a spare pump head for use with different fluids. Some customers have separate pump heads for use with each fluid handled or flow rate desired.
|
|
| ... products without technical information |
| |
|
Low-maintenance spray marking system produces neat circles and stripes between from .2%u201D to 1.2%u201D wide. A programmable air delay after each cycle prevents clogging, which greatly reduces maintenance and downtime.
|
|
| ... products without technical information |
| |
|
The Meech Model 904 is a constant voltage power supply, designed to provide a 7kV source for Meech AC ionising equipment. It is adjustable to operate at 100-120v or 200-240v input voltages and is available in either 50Hz and 60Hz versions to suit local conditions. The 904 utilises a modified shape of output wave form and is uniquely designed to allow automated manufacture for increased reliability and extended product life.
|
|
|
The 977CM - Current Monitoring Pulsed DC Controller, brings together powerful long-range ionisation; closed-loop feedback; self-monitoring and remote reporting. A complete package, unique to Meech. Self-monitoring and adjustment of performance allows optimum control of static for much longer periods than previously possible. Local display and output signals alert operators to the need to clean the equipment.
|
|
|
The Model 977v3 Pulsed DC Controller has been designed to operate with the full industrial range of Meech Pulsed DC static elimination equipment. It is light and compact but able to cope with the most technically demanding industrial applications. In addition to the ability to control power output, frequency and polarity, the 977v3 also offers alarm and remote monitoring and control functionality. A new feature of the 977v3 is an 8- way DIN for connection of an ion balance sensor and feedback system. Patent No. ZL200530000278.0
|
|
|
The Model 233v3 Pulsed DC Controller has been designed to operate with the Series 200 range of ionisers for ESD applications. The 233v3 is light, compact and features lockable plug and socket connectors for quick release. It also provides the option of Steady State DC (SSDC) output.
|
|
The Turbo-Flo can be used as assisted or unassisted fresh air breathing apparatus. As unassisted fresh air breathing apparatus the air is drawn through a hose of max. 18 m. As assisted fresh air breathing apparatus, the Turbo-Flo blower is connected.
- Sturdy design
- Easy to carry and use-simple to maintain
- Good mobility, twin breathing tubes over shoulders
- Turbo-assisted breathing (with Turbo-Flo blower)
- Independent of power supply (without blower)
|
|
Breathing Star
Type Capacity Connection Weight
m3/h kg
BSP-MT 1 8 G 1/4 13
BSP-MT 2 15 G 1/4 19
BSP-MT 3 25 G 1/4 25
BSP-MT 4 35 G 1/4 35
BSP-MT 6 56 G 3/8 74
BSP-MT 7 72 G 3/8 92
BSP-MT 8 86 G 1/2 109
BSP-MT 200 130 G 1 160
BSP-MT 300 170 G 1 191
BSP-MT 400 230 G 1 267
BSP-MT 500 300 G 1 329
BSP-MT 600 365 G 1 1/2 374
BSP-MT 800 520 G 1 1/2 492
BSP-MT 1150 700 G 1 1/2 636
BSP-MT 1400 850 G 2 730
|
|
A wide variety of different Air Purifying Respirators and filters - the right product for every application!
Our range of light respiratory protection products covers everything from Particle Filtering Facepieces to Powered Air Purifying Respirators.
Powered Air Purifying Respirators
Whenever you need respiratory protection with high comfort, a Powered Air Purifying Respirator is providing you with a high level of comfort.
Low breathing resistance and the constant air flow will guarantee the best comfort possible in such applications.
|
|
|
Dräger supplies high pressure breathing air compressors suitable for all kinds of different applications.Dräger plans, assembles and provides after-sales service for gas filling systems for industry and fire brigades,as well as for small recreational diving compressor systems above 100 L/min.
|
|
Applications include:
-Automotive sheet metal and components
-High-speed bi-metal contact welding
-Storage Batteries
-Aircraft components (aluminum and titanium)
-Nut resistance spot welding
-Projection welds
-Motor armature fusing
-Markless welding
The ISA range of Inverter power supplies provides the highest level of control available today in large scale resistance spot welding. All models are intelligently packaged in “NEMA” style enclosures and are designed to deliver robust performance in the harshest of production environments.
|
|
Inverter Power Supply - IS 120
Inverter Power Unit
Controlled DC Inverter for a wide range of applications - Compact device with terminal and remote transformer
Features
External programming panel
Connection to all mian voltages
Indication of all actual values
Status and error detection in clear text
Applications
Well-suited for automation
Maximum quality requirements
Safety critical environment
Materials with very poor welding properties
Use
Economical and efficient operation
Stable processing and high reproducibility
High grade of weld
Integrated process monitoring
Optimum quality documentation
|
|
|
|
|
|
Miyachi Europe offers the high end welding system AWS3 with ISQ 20-10K especially for automotive, tooling and electric/electronic industry requiring high end interfacing and high speed automation. The new product expands the weld current range up to 10kA.
Applications:
Automotive: Lead frame welds, connectors, compacting, pumps, motors, coils
Tooling: Burrs, saw blades large
Electric/Electronic: Components (e.g. capacitors, resistors), fuses, motor switches, relays, contacts, electrical motor fusing, magnet wire welding
Technical Specifications:
max current weld head with short secondary cables 2 x 400mm², length 500mm measured = 10kA
Benefits:
+ Compact design like ISQ20-6
+ High duty cycle
+ High output power (250A)
+ External transformer water cooled
+ Interfacing identical to ISQ20-6
+ Full AWS3 functionality
Dimensions (mm):
Inverter: 216 x 420 x 480 (W x D x H)
Transformer: 284 x 110 x 170 (W x D x H)
Weight (in kg): Inverter: 20kg; Transformer: 16kg
Power requirements: 3 x 400VAC, 50/60 Hz, 20kVA
Legal Approvals: CE compliant
|
|
Inverter type power supply for spot welding (resistance)
Average rate 1000 - 2000 Hz
18 to 72 KA standard - Parallel to strong currents
QUALITY - PERFORMANCE
- Provision of energy very quickly
- Time welding reduced
- Low projection area
- High quality welding
- Increased speed welding
- Ideally suited for hard coating materials
- Welding of non-ferrous materials (aluminum - copper - brass - etc ...)
- High reproductibility of welding points
- Loop and exhibit no influence on the welding
- Ease of integration transformer welding weight and small size (board)
ECONOMY
- Performance (70%)
- Reduction of energy consumption
- Reduced infrastructure costs
- Need cooling reduced
- Low wear electrodes
CONTROLLER FOR THE RESISTANCE WELDING
|
|
|
|
see the results for the following category : 
