|
|
|
HazardWatch is a modular Fire and Gas Detection System built using state-of-the-art industrial automation/control equipment to perform the requirements of an integrated Fire and Gas Detection System certified by Factory Mutual to be compliant to NFPA 72 (2002).
|
|
Secure field bus for Fire & Gas system solution
WITHOUT COMMUN FAILURE MODE
Since 1948, SIMTRONICS has specialised in high technology products for the analysis and detection of gas. Today, the Syntel System and its new line of remote sensors come at the leading edge of technologic innovation (30 registered patents) to guarantee a safe and efficient secured system :
• Very high safety level, SIL 2
• Distributed intelligence protocol where each sensor interacts with output modules,
• Safety ring topology with a single cable brings reduced costs,
• Open system,
• Integration and control of digital and analog signals,
• MODBUS / LonWorks gateway enabling connection with supervision systems, SCADA, PLC,
• Flexible configuration using its own dedicated configuration tool,
• Easy-to-use exploitation system.
|
|
|
|
|
|
Gasmonitor Plus is just one of Crowcon’s control panel range. This flexible, rack based, microprocessor-controlled unit is used throughout the world, both onshore and offshore. Gasmonitor Plus provides the cost-effective solution to your system requirements.
Features:
Simple to Use
• All the day to day functions are available from the front panel
• The unique bar graph display per channel provides an instant representation of gas concentrations
• Common alarm LEDs on the display card mean that the whole rack status can be checked at a glance.
Flexible Architecture
• System is limitlessly expandable
• System customisation is achievable with minimal wiring
• Designed to industrial standards, Gasmonitor Plus will integrate fully with existing rack mounted protection systems on site
• Optional relay modules can be used to provide up to a total of 84 output relays per rack.
• Sixteen of these relays can be voted to activate from a combination of the three levels of alarm per channel
Other controllers in our fixed gas monitoring range include:
Vortex 1 to 12 channel control system
Gasmaster 1 to 4 channel control system
Gasflag Single channel control system
CellarSafe CO2 monitoring system
Ditech modular gas and fire detection and extinguishant control system
|
|
The new CheckBox IMH automates the routine gas (bump) testing, calibration and management of Crowcon portable gas detectors and facilitates the traceability and routine maintenance of instruments. Capable of operating with up to 10 instrument interfaces, CheckBOx IMH is available for use with the Tetra, Triple Plus Plus and Gasman products.
* Automatic gas (bump) testing
* Automatic calibration
* Can use single gases or quad mixtures
* Up to eight gas inlets
* Five or ten instrument interfaces
* Accommodates pumped or non pumped instruments
* Data and event file uploading
* Stores and controls configurations
* Records all activities
* Provides reports and certificates
|
|
|
|
|
|
The DirectSense Ultra-Mini PC based advanced environmental monitors include USB enabled multi-sensor probes and a Mobile PC platform.
Measure ppb range volatile organic compounds (VOCs), Carbon Dioxide, CO, °C/°F, %RH and an additional specific gas for IAQ applications with a single probe. Alternative probes allow you to simultaneously measure up to 5 specific toxic gases (H2S, O3, NH3, SO2, NO2; choose from 21 specific gas sensors) and/or ppm range VOCs, air velocity, differential pressure, particle concentration and other parameters.
The new Fujitsu Ultra-Mini Vista OS mobile PC sports a swiveling, touch screen and easy-to-use keyboard. A built-in camera is great for photos (or panoramic videos) that attach to data files on-site. It's easy to carry (in-hand or in shoulder pouch) for spot-checking and spot-logging, yet it fits easily into GrayWolf's hard-shell security case for unattended trend logging.
Plug in any of GrayWolf's USB enabled DirectSense probes and you have a very powerful monitor, with features not available from any other instrument:
•On-board video help
•On-board sensor info (basic sensor care, cross-interferences, etc)
•On-board parameter details (typical sources, typical background levels, government guidelines, etc)
•On-board application related documents
•In-situ text notation
•In-situ audio notation and much more
Measurements collected in the field can be analyzed, and reports on the data and field collected note with the included WolfSense® PC software. Create tables and histograms comparing measurements from various locations in seconds. Even automate the entire reporting process with GrayWolf's optional Advancaed Report Generator software.
|
|
Automatic Sensor Cleaning Unit Model 73100
High quality analyzer for industrial use
The new MecSens automatic sensor cleaning unit is a breakthrough in cleaning performance and efficiency. The unit will operate automatically and clean all electrodes sequentially in a controlled cycle, or the operator selects the individual electrode he wants to clean (anode, cathode and guard). There is no hassle with grounding cables between the sensor and the cleaning instrument and the automatic cycle will clean the sensor so thoroughly that chemical cleaning will only be required in very few cases. The unit is provided together with the container adaptor for MecSens sensors but adaptors for selected other electro- chemical makes can be provided as an option.
|
|
|
|
|
|
The MicroDock II is the world’s most advanced, compact and affordable automatic calibration, testing and data management system for portable gas detection equipment. Compatible with BW’s GasAlertMicro 5, GasAlertMicro 5 PID, GasAlertMicro, GasAlertMicroClip, GasAlert Extreme and GasAlertClip Extreme family, the MicroDock II is expandable to up to 10 docking modules (including up to 6 charging units).
- Fully automatic “hands-free” calibration & functional bump test
- Automatically verifies performance of audible and visual alarms
- No computer required
- Entirely self-contained
- Fully portable
- Lightweight and mobile
- Operates via line power or a set of four C-cell batteries
- Add additional self-contained docking modules to system via simple, plug-in connections-no external pressure transducers or gas lines necessary
- Simplify record keeping
-Verify proper performance
- Reduce maintenance costs
- Multiple MicroDock II systems can be connected via a LAN
- Multi-language support in English, French, German, Spanish, and Portuguese
|
|
The DS2 Docking Station provides the ultimate flexibility for managing your gas monitors wherever you use them. The DS2 gives you all of the benefits of consistent automated calibration, record keeping, battery recharging and instrument diagnostics for your monitors to limit your liabilities and safety hazards. Two way wireless and/or ethernet connectivity enables you to link up to 100 stand-alone Instrument Docking Stations (IDSs) from remote locations anywhere in your facility and relay the data back to one central database for total instrument management. A graphical user interface tool (DSSAC) allows an administrator to view operations on each Docking Station from a network computer, making it easy to track instruments, print reports, set events and change parameters for any location.
|
|
The ToxiRAE II is a single gas, reusable personal protection monitor that continuously displays toxic gas concentrations. Unlike typical disposables that only display "remaining life", the ToxiRAE II is a full-featured gas monitor providing continuous, digital display of the gas concentration, STEL, TWA, and Peak values as well as high, low, TWA, and STEL alarms.
A simple to use one-button product, the ToxiRAE II is easy to calibrate. Use the pre-set alarms, or modify the alarms to meet your specific requirements. In contrast to disposables that are turned on once and remain on until their batteries expire, you decide when and where to use your ToxiRAE II and you turn it on and off accordingly.
This product has ATEX approval.
|
|
|
|
|
|
The ToxiRAE 3 is a full-featured single-gas monitor that offers unequaled cost of ownership value. The ToxiRAE 3 is compatible with the AutoRAE Lite bump and calibration station, http://www.raesystems.com/products/autoraelite
STEL, TWA, low, and high alarms can also be recorded. The detector is warranted for 2 years and maintenance free with replaceable battery.
Overview:
— Lowest cost of ownership on the market.
— Rugged steel housing for harsh environments.
— Fastest instrument response time on the market for better protection and worker safety.
— Fastest bump station on the market with highest productivity, putting workers back to work quickly.
— Compact, low-cost bump and calibration station enables the ability to put the bump capability where it is needed.
Key Features:
- High-performance 3-electrode pinless micro sensor with the fastest response time
- 0.1 ppm H2S resolution, and high-range 1999 ppm CO available
- Large, easy-to-read display facilitates overview of gas concentration or days remaining (end-user adjustable)
- Event logging of up to 10 events
- Full activity records when used with AutoRAE Lite calibration station
- Intuitive, simple-to-operate user interface
- IP-67 water-proof and dust resistant
- Loud, 95 dB audible alarm, bright red flashing visible LEDs and internal vibration alarm
- Color-coded labels for gas type
- Extended operating temperature of -4° to 140° F (-20° to +60° C) with full T4 approval
- User-configurable bump/calibration reminders
Gas Range (ppm) Resolution (ppm)
Hydrogen Sulfide (H2S) 0-100 0.1
Carbon Monoxide (CO) 0-500 1
Carbon Monoxide (CO) 0-1999 1
|
|
GasCal 1100 Gas Dilution Calibrator
The Ecotech GasCal 1100 Gas Dilution Calibrator performs precise
gas dilution calibrations, ozone analyser precision checks and gas
phase titrations using an optional internal ozone generator. It is
ideal for stand alone use or incorporation into ambient air or emissions
monitoring systems.
• Single and multipoint calibrations can be performed using precise mass flow controllers
• Perform gas phase titrations (U.S. EPA Method) and ozone precision checks using an internal ozone generator (option)
• Parameter setup and output via inbuilt LCD and keypad or an external PC
• External remote control possible via data acquisition system or suitable gas analyser
• Mass flow controller zero stability drift less than 0.6 % full scale per year
• Optional Carry case allowing the GasCal-1100 to be securely carried from location to location
• Optional purge facilitates flushing of calibration gas lines
|
|
Compact Multi-gas Detector for H2S, CO, O2, Combustibles
The QRAE II is a full-featured, compact, one- to four-sensor gas detector for detection of combustibles, oxygen, hydrogen sulfide, and carbon monoxide. Key features include easy-to-change, externally accessed battery packs (available in rechargeable and alkaline versions), a water-resistant case and a new state-of-the-art O2 sensor technology with extended life.
Key features include:
Patented SPE O2? Oxygen sensor
Best EMI/RFI immunity technology for products in its class, eliminating radio interference
Easy access to sensors, filter and battery compartment without exposing electronic components to potential damage
Big graphic display for easy overview of gas type and concentration
Alkaline adapter and Lithium-ion battery pack
Rugged housing withstands harsh environments
|
|
The MultiRAE Plus combines a PID (Photoionization Detector) with the standard four gases of a confined space monitor (O2, LEL, and two toxic gas sensors) in one compact monitor with sampling pump. The MultiRAE Plus gets the job done in more circumstances than any other gas detector. The MultiRAE Plus is quickly and easily changed from a sophisticated technician instrument to a simple text-only monitor. The same monitor can be used as a personal monitor, a hand-held sniffer, or as a continuous operational area monitor.
The MultiRAE Plus detector can be made wireless with the use of RAELink. This allows real-time monitoring information from the detector to be integrated into an existing AreaRAE system. A wireless, RF (radio frequency) modem allows detectors to communicate and transmit readings and other information on a real-time basis with a remotely located AreaRAE base controller up to two miles away.
This product has ATEX approval.
|
|
|
|
|
|
AreaRAE Steel is the first ATEX certificated Wireless Monitor in Europe with up to 5 simultaneous gas sensors including Toxic Industrial Chemicals. It runs licence-free communication and RAE Systems can show over 2.500 installed base.
The AreaRAE Steel is housed in a welded stainless-steel enclosure, it is rugged, portable and weather-resistant, making it suitable for harsh environments. Ideal for hazardous materials and other emergency response monitoring applications, strategically placed AreaRAE Steel monitors can be used to quickly establish a perimeter, allowing first responders to back off to a safe position and monitor readings from up to 3 kilometers away.
The photoionization detector (PID) in the AreaRAE Steel can measure parts per million of volatile organic compounds (VOCs). In addition, it can be equipped with a lower explosive limit (LEL) sensor, an oxygen sensor, and one or two electrochemical toxic sensors for measuring specific substances such as hydrogen sulfide or chlorine.
An integrated wireless modem transmits real-time gas measurement data to a base station, which employs a standard Windows-based PC running ProRAE Remote software.
Key Features
- Up to five sensors (PID, LEL, O2 and two electrochemical toxic gas)
- Loud buzzer and large, extra-bright warning light
- Large LCD display and keypad
- Rugged, weather-resistant stainless-steel housing
- Built-in sampling pump
- Interchangeable Li-ion or alkaline battery pack
- Continuous operation via AC source
Applications
- HazMat and Emergency Response
- Refineries and Petrochemical Plants
- Power Plants
- Pulp and Paper Industry
- Marine and Offshore Wells
|
|
| ... products without technical information |
| |
|
HazardWatch is a modular Fire and Gas Detection System built using state-of-the-art industrial automation/control equipment to perform the requirements of an integrated Fire and Gas Detection System certified by Factory Mutual to be compliant to NFPA 72 (2002).
|
|
Secure field bus for Fire & Gas system solution
WITHOUT COMMUN FAILURE MODE
Since 1948, SIMTRONICS has specialised in high technology products for the analysis and detection of gas. Today, the Syntel System and its new line of remote sensors come at the leading edge of technologic innovation (30 registered patents) to guarantee a safe and efficient secured system :
• Very high safety level, SIL 2
• Distributed intelligence protocol where each sensor interacts with output modules,
• Safety ring topology with a single cable brings reduced costs,
• Open system,
• Integration and control of digital and analog signals,
• MODBUS / LonWorks gateway enabling connection with supervision systems, SCADA, PLC,
• Flexible configuration using its own dedicated configuration tool,
• Easy-to-use exploitation system.
|
|
LAND offers a system capable of monitoring the entire coal handling process including applications such as coal storage and transportation as well as the actual grinding.
The early detection of a coal fire is vital to the safe and efficient operation of any plant. LAND has a range of coal fire detection systems based upon the best monitoring technology available.
|
|
The automated early fire detection system WASTE-SCAN is based on the principle of infrared thermography. It provides a continuous, non-contact temperature measurement at the surface of a waste collection, even over large distances.
Main item of the system is the high-resolution thermographic camera VarioCAM® hr head manufactured by the German company JENOPTIK Laser, Optik, Systeme GmbH. It is based on an uncooled microbolometer detector FPA.
The thermographic camera VarioCAM® hr head has the following performance parameters:
(384 x 288) or (640 x 480) pixels for high geometrical resolution
high-contrast, low-noise thermal image
localisation of hot spots, even under dusty or smokey conditions
spectral range (7.5 ... 14) µm
real-time data acquisition at 50 / 60 Hz frame rate
internal automatic calibration.
|
|
|
With the fire detection system PYROVIEW/PYROSOFT WBFDS DIAS Infrared GmbH, VdS certified manufacturer of infrared cameras, offers you a complete system for supervision of your plants. Certified infrared cameras PYROVIEW are the heart of the automatic fire detection system. Infrared cameras PYROVIEW are based on state-of-the-art microbolometer arrays with up to 384 x 288 pixel and are well suited for industrial use with their robust housings and optional cooling and air purge systems.
|
|
|
When automatic 24/7 fire protection is required, select from our complete line of AUTOPULSE® detection, control and fire suppression system release panels. Detection options include smoke, heat and flame detection. Also consider our VESDA® aspirating smoke detection technology.
|
|
HAREZMIC SERIES INTELLIGENT ANALOGUE ADDRESSABLE SYSTEM ACCESSORIES
VIP (Very Intelligent Protocol) compatible.SSPB (Russia) and GOST R certified.
Approved by Kazakhstan, Oman, UAE, and Bahrain Civil Defence authorities.
Microprocessor-controlled
"Sof" addressable by use of Address Programmer
Easily programable by use of Loop Manager
Able to integrate into the cause-effect scenarios.
LED-indicated activation
Monitoring analogue value
Mesuring contamination level
Aesthetic design
Production by surface-mount technology
|
|
MG-9000 SERIES INTELLIGENT ANALOGUE ADDRESSABLE FIRE DETECTORS
VIP (Very Intelligent Protocol) compatible. EN 54, EMC-CE and SSPB (Russia) and GOST R certified. Approved by Kazakhstan, Oman, UAE and Bahrain Civil Defence authorities.
Features
EN 54-5 ve EN 54-7 certified
Twin fire alarm indicators for 360° viewing
Soft addressable by use of Address Programmer
Remote indicator output
Communication interrupt for fast fire
alarm detection in 3 sec
Stable sensitivity
PCB protected by metal case
Protection from electromagnetic interference
MG-3510 Addressable Mounting Base compatible
MG-3600 Recessed Mounting Base compatible
Microprocessor-controlled
Clamp terminals to ensure firm contact with the base
Produced by use of Surface Mount Technology
|
|
|
|
|
|
MAVIGARD MG-104 SERIES CONVENTIONAL EXTINGUISHANT CONTROL PANEL
MG-104 Series operates on cross-zone principle, has 4 detection zones and one
extinguishant release output which can be programmed according to site
needs. SSPB (Russia) and GOST R certified. Approved by Kazakhstan and Oman Civil Defence authorities.
Highlights
* 4 zones, 1 extinguishant release output
* Configurable latching/non-latching zones
* Configurable detection of short circuit as fire alarm
* Distinguished detector/MCP alarm detection
* Programmable 1st Stage sounder output delay
* Programmable extinguishant release duration
* Extinguishant release countdown timer
* Manual and Automatic/Manual extinguishant modes
* 1st and 2nd Stage relay outputs
* Solenoid valve and actuator compatible
* Remote control
* 6 programmable relay outputs
Features
Soft-touch buttons
Microprocessor-controlled
PCBs made by use of Surface Mount Technology
3 programmable and supervised sounder outputs
Compatible with all popular conventional fire detectors
Protection against electromagnetic interference
Optional repeater panels
Optional relay modules
Auxiliary power supply output
Display and LED test by use of single button
Built-in silencable buzzer
|
|
|
|
|
|
MG/MGR-2000 SERIES CONVENTIONAL FIRE DETECTORS
Designed and produced according to EN 54 by use of Surface Mount Technology
providing stable sensitivity. EN 54, EMC-CE and SSPB (Russia) and GOST R certified.Approved by Kazakhstan, Oman, UAE and Bahrain Civil Defence authorities...
Superior design and excellent functional features of the MaviGard detectors are the result of the Research & Development work done using latest technological achievements in the fire alarm industry. Detectors are produced with Surface Mount Technology (SMT). Detector PCB is protected against electromagnetic interference and corrosion by minimizing contact with external medium. MG series detectors are compatible with all fire alarm control panels,
MGR series detectors are compatible with all security alarm control panels. All detectors are provided with blue plastic cover, which protects detector from dust, dirt etc. during construction and paint. Detectors are produced in white as standard but, according to customer's choice, various colours are available. Detectors can be provided with magnet-testing feature on customer's demand.
Features
* Stable sensitivity
* Microprocessor-controlled
* MGR models with relay output
* Twin fire alarm indicators for 360°
viewing
* PCB protected by metal case
* Protection from electromagnetic
interference
* Clamps terminals to ensure firm
contact with the base
* MG-3500 Universal Mounting Base
compatible
* MG-3600 Recessed Mounting Base
compatible
* Remote indicator output
* In MGR series normally close relay
output as standard (normally openalso available)
|
|
|
|
|
|
FN-LCD-N (9th Edition), LCD Network Annunciator,
STANDARD FEATURES
Dual RS-485 ports for primary fire network
RS485 slave bus for expansion - up to 32 FN-4127-IO boards or up to 15 FN-LCD-S serial annunciators and up to 16 FN-4127-IO boards
2 built-in RS-232 interfaces for programming via a PC and serial printer interface
4 on board programmable Form C relays rated at 1 Amp at 30VDC (Fire, Supervisory, Trouble & Auxiliary)
Same controls as the FireNET fire panel (Reset, Panel Sounder Silence, Lamp Test, Alarm Silence, Re-sound Alarm, Fire Drill, Programmable Function, More Events, More Fire Events, Enter & Exit)
Local piezo sounder for event notification
Supports user codes & firefighter key to enable access & controls
Powered by FireNET Aux 24VDC or UL fire listed Aux. 24VDC supply
Available in red or charcoal, and can be surface or flush mounted (using trim ring)
True network annunciator, any or all panels can be routed to the FN-LCD-N. In addition, each event category can be individually routed to the FN-LCD-N
Up to 64 FireNET panels & FN-LCD-N's can be networked together in any combination
500mA of auxiliary power available rated at 24VDC
Auto-learn feature
Built-in help & alarm information screens
Fire Drill function
Each FN-LCD-N is completely independent
Supports up to 32 FN-4127-IO boards on RS485 expansion port
The FN-LCD-N can be configured to remote reset, silence, resound, any or all panels on the network in any combination
|
|
|
|
see the results for the following category : 
