|
|
A range of DC drive systems specially tailored for the mobility market.
MOTORS
PM36 Custom permanent magnet motors up to 75 watts.
PM45 Custom permanent magnet motors up to 250 watts.
PM55 Custom permanent magnet motors up to 300 watts.
PM62 Custom permanent magnet motors up to 500 watts.
GEARBOXES
G30 Custom non declutch right angle gearboxes to 11Nm torque.
G34 Custom declutch right angle gearboxes to 40Nm torque.
G46 Compact right angle gearboxes to 20Nm torque
G46M Compact right angle gearbox specifically for heavier duty mobility applications.
G63 Compact Hi-Duty right angle gearboxes to 25Nm torque.
G120 In-line gearboxes to 30Nm torque.
TRANSAXLE
A unique Power Train for heavy-duty applications, compatible with PM62 & PM55 motors.
minimum order quantity: 100 units per annum
|
|
|
Production of worm gear units and electric motors sizes 030 to130 reduction ratio 1:7 to 1:100
|
|
Tritex Series brushless servo-gearmotor with amplifier and control
Frame Size 2 – 3.5 inches, 51 – 89 mm
Maximum Continuous Torque Rating 2078 lbf-in, 235 Nm
Maximum Motor Speed 2500 rpm
|
|
The High Performance AR Series Single Axis Positioning Actuator consists of a zero-backlash / trouble-free RV reducer, compact servomotor, amplifier and controller - all within one unit.
The AR Series can support heavy loads due to the integrated support bearings in the RV reducer with high positional accuracy and excellent repeatability.
The AR series can accommodate up to 255 addresses and is ideal for a variety of applications where precise motion control is required, including: Headstock / Tailstock, Index Table, Robotic axis, ATC Magazine and Semiconductor equipment.
|
|
Gear motor with worm screw and standard motor Ø 42 30 output W 24 Vdc 3700 RPM loadness, with electric noise
suppressor. Driving shaft mounted on a bearing and bushing. Outlet shaft supported by two bearings with oil splash
guard on the outlet side.
* The rotation speed can change of ± 10%.
Connecting 2 wire 0,75 x 250 mm.
The S1 load test was made using a 1,6 A corrent in the air with an increase of temperature of 70 C°
The S2 load test was made using a 3,0 A corrent in the air with a timing 5' ON 5' OFF with an increase of temperature
of 80 C° max
The starting corrent is 5 A and cannot be maintained for more than 2"
Max forces wich may act on the outlet shaft: Axial 25 kg, Radial 40 kg
It is possible to apply encoder
|
|
|
Production of worm gear units and electric motors sizes 030 to130 reduction ratio 1:7 to 1:100
|
|
MSF/MSF combined worm gear motors
Worm gear speed reducers type SF-MSF are a new generation of products developed by our company.
|
|
ROTEK worm gears -- twice as useful due to second shaft end
Smooth running - maintenance free technology
The worm gear transmission S can be used wherever you need a second shaft end, or to deflect forces by 90°. Additionally, the motor can be fitted at 90° to the device axis.
Fabric-based laminate worm gears give these transmissions the extremely smooth running performance needed for use in medical and laboratory applications. Bronze worm gears are available for applications with heavy loads and for longer service life.
Benefits
> Apply force at 90° to machine
> second shaft end
> Self-locking with higher gear ratios
Charateristics
> smooth running
> maintenance free
Options
> customized shafts
> special lubrication
> Bronze worm gears
|
|
|
Venture has a variety of gearboxes available, both motorized and manual. Many are customizable to suit your specific need. If we don't have exactly what you need contact us and we will be happy to investigate making a custom unit for your specific application.
|
|
Due to the unique combination of newly developed worm wheel material with special lubricants, extreme precision and optimized shapes, this powerful motor achieves comparatively high levels of efficiency and torque. The case machined on all sides enables diverse mounting options.
Double-chamber shaft seals made of HNBR are used as standard, guaranteeing complete leak tightness.
|
|
STRÖTER Worm gear motors
Torque range - 2000 Nm
Standard design
* three phase IEC AC-motor
* voltage : 230/400 V - 400/690 V
* type of protection : IP 55
* insulation class : B
* mounting position : D
* output shaft : hollow shaft or solid shaft (A or B)
STRÖTER Worm gear motors / power range 0,12 - 2,2 kW
|
|
|
|
|
|
ABM helical geared motors, shaft mounted helical motors and planetary back geared motors give added power to the motor torque and reduce the speed to the necessary level. Helical geared motors and shaft mounted helical motors are those most widely used in industrial applications.
These ABM drive units are particularly known for their:
energy saving of 98% efficiency at each stage
economy due to favourable cost/performance ratio
rugged and practically maintenance-free
environment friendly drive type (compared with internal combustion engine, hydraulics, pneumatics)
The high-quality helical gearing with polished tooth profiles guarantee complete smoothness of operation and accurate power transmission.
ABM Helical Geared Motors
a shaft height of 71 mm to 315 mm
drive torque of 30 to 6000 Nm
rpm from 2 to 750 rpm
ABM Shaft Mounted Helical Motors
drive torque up to 2500 Nm
speed from 3 to 220 rpm
reduction ratios of 6 to 250 to 1
ABM Planetary Geared Motors
drive torque up to 700 Nm
reduction ratios, single stage up to i = 12
all further details upon enquiry
|
|
KEB COMBIGEAR S Helical Worm Geared Motors
The KEB helical worm geared motors are available in the power range 0.12…12kW representing the “standard gear" in machines and systems due to their superior economic efficiency.
Lifetime lubrication, universal mounting construction and varied output options (solid shaft, hollow shaft) make this geared motor extremely adaptable
|
|
|
|
|
|
SEW-Eurodrive's S-Series gearmotors (right angle) offer helical-before-worm gearing combining durability with power-packed performance in a compact design that requires no motor belts or couplings.
-Reducers
Worm shaft and helical gears manufactured from certified steel, heat treated to a case hardness of 58-62 Rockwell C for long gear life
Gears are milled, hardened and ground to assure maximum efficiency (up to 94%), minimum noise and heat generation
High capacity anti-friction bearings for optimum load carrying capacity and long life
Captured keys on input and output shafts
Gearcases made of high strength gray cast iron, SAE Class 30
High cross-section modulus design with stiffening webs for maximum rigidity
S-Series reducers are continuous duty at rated thermal capacity, based on ratio and input speed
Center tapped holes on output shafts
Double output seal design consisting of patented bi-helix inner seal made of Viton® and double-lip Nitrile (Buna-N) outer seal*
-Motors
NEMA Design B/C
Inverter duty
Connection terminals
Extremely low motor inertia
Mark for shipment into Europe
|
|
Efficient compact right-angle geared motor. A favorably priced alternative for the standard tasks expected of a right-angle drive.
- Sizes:
- S0 – S4.
- Rated torque:
- 23 – 800 Nm.
- Motor power:
- 0.12 – 9.2 kW.
- Gear ratio range:
- 6 – 683.
|
|
Worm gear units up to 20 Nm
Fed up of compromises or expensive customized gear motor solutions? Have a look at HeiDrive - the intelligent gear motor programme!
Configurate a gear motor perfectly adapted to your needs and requirements by choosing from different gear sizes, a variety of ratios
and a broad range of motor types and accessories. Whether you are in need of helical gears, helical bevel gears or worm gears -
HeiDrive always offers you the right choice!
Following ratios/torques are available:
Size S031 S031
Ratio i 7,0 up to 100,0 : 1 7,0 up to 100,0 : 1
Torque Mzth [Nm] up to 6 up to 6
Combination with motor type 3 phase motor 3 phase motor
Motor power P2 [W] 30 - 80 30 - 80
Motor speed [rpm] 2700 2700
|
|
Gear motor with worm screw and standard motor Ø 37x34 24 Vdc 5000 RPM output W, with noise suppressor.
Driving shaft mounted on two bearing and bushing. Outlet shaft supported by two bearings.
Design to give low RPM in little dimension
* The rotation speed can change of ± 10%.
The S1 load test was made using a 0,8 A corrent in the air with an increase of temperature of 70 C°
The S2 load test was made using a 1,5 A corrent in the air with a timing 5' ON 5' OFF with an increase of temperature
of 80 C° max
The starting corrent is 4 A and cannot be maintained for more than 2"
Max forces wich may act on the outlet shaft: Axial 25 kg, Radial 40 kg
It is possible to apply an encoder.
|
|
ASTRO a phase synchronous geared motor AS 80-6
Ex engine after guideline 94/9/EG (ATEX)
Compact building method
Area of application:
Gases, steams or fog "G"
Types of dust "D"
z.B. Automotive, printing, food, regulation industry
1~24V for 50 or 60 cycles per second
Speed range 0.75 - 1200 Upm
High stable torque process
GROUP OF EQUIPMENT II
Category 1
very high measure of security
Zone 0 and 20 = no permission
Category 2 = permissions
high measure of security
Zone 1 = G (gas)
Zone 21 = D (dust)
Category 3
normal measure of security
Zone 2 = G (gas)
Zone 22 = D (dust)
Ignition enclosure:
G = gas/zone 1
Engine: Ex II 2 G ex e II T4
Gear motor: Ex II 2 G ex ec II T4
D = dust/zone 21
Engine: Ex II 2 D ex tD A21 IP65 T 90°C
Gear motor: Ex II 2 D ex tD C A21 IP65 T 90°C
LARVA IN GERMANY
|
|
Type
RK543AA
Series
5-phase with microstep (RK-Series) (Standard type)
Technical data
Type
RK543AA
Frame size [mm]
42
Shaft type
single
Holding torque [Nm]
0.13
Step angle [°]
0.72
Power supply
single-phase 100-115 VAC
RoHS-compliant
yes
|
|
With MOTOX we offer both a modular geared motor range and a comphrensive range of frequency inverters.
Torque range: up to 20,000 Nm
Power rating: up to 200 kW
|
|
A broad line of Browning helical gearmotors & speed reducers for a variety of industrial applications with most available from stock. Browning offers a complete line of helical shaft mount, right angle helical-worm and helical-bevel as well as inline helical concentric gearing products.
The Browning TorqTaper® Plus helical shaft mount speed reducer is ideal for bulk handling applications. The patented TorqTaper® Plus mounting system allows ease of installation and removal while the patented Barrier seal system provides protection in tough applications. 8 basic sizes are available from stock with mounting on shafts ranging from 3/4 " to 8". All Browning TorqTaper® Plus have tapered roller bearings for excellent thrust capacity. Offered with traditional belt drive inputs as well as hydraulic and NEMA C-Face inputs...Modular CEMA screw conveyor adaptor kits are also available from stock.
|
|
Our most selling and most economical unit, the BG gearmotor, sets new standards for reliability and economy and includes unparalleled standard features.
Features and benefits
Product range
Power rating up to 45 kW.
Main features
* Torque 20 ... 18.500 Nm
* Output Speeds 0,3 ... 450 min-1
* versatile installation possibilities
* Completely enclosed, sealed against dust and water spray
* Lubrication change first after 15000 hrs
* Low noise gearing
* Mains connection 110 ... 690V, 50/60Hz
* Enclosure IP65 (Standard), IP66 (Optional)
* Connection Standard with CAGE CLAMP®
* Additional features:
Connecting with Plug connectors.
With integrated inverter up to 7,5kW.
* CE-Mark
* CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
* Motors according to EN 60034
* Corrosion protection CORO1, CORO2, CORO3
|
|
Length "L" of the gearmotor as a funtion of reduction and outlet number of revolution with the standard motor
752 40 output W 2900 Rpm loadness, 12/24 Vdc. Drivingshaft supported by self lubrificating bushings. Outlet shaft
supported by two coupled screened bearings. The motor and the reduction gear are both thrated for corrosion strength.
The motor has an electrical suppressor system for the CE standard.
Connecting 2 wire 0,75 x 200 mm.
* The rotation speed can change of ± 10%.
The S1 load test was made using a 1,3 A corrent in the air with an increase of temperature of 70° C.
The S2 load test was made using a 2,6 A corrent in the air with a timing 5' ON 5' OFF with an increase of temperature
of 80° C max
The starting corrent is 7 A and cannot be maintained for more than 2".
Max forces which may act on the outlet shaft: Axial 30 kg, Radial 40 kg on the extremity of outlet shaft
|
|
In-Line Gearboxes to 30Nm torque and 120Nm torque ratios. Available with a range of DC Motors and varying ratios.
Including:
G120 In-line gearboxes to 30Nm torque.
IMS In-line gearboxes to 120Nm torque
PM36 Custom permanent magnet motors up to 75 watts.
PM45 Custom permanent magnet motors up to 250 watts.
PM55 Custom permanent magnet motors up to 300 watts.
PM62 Custom permanent magnet motors up to 500 watts.
minimum order quantity: 100 units per annum
|
|
Length "L" of the gearmotor as a funtion of reduction and outlet number of revolution with the standard motor 763 60 output W 3400 Rpm loadness, 24 Vdc. Outlet shaft is supported by two coupled screened bearings.
The motor has an electrical suppressor system for the CE standard.
The motor and the reduction gear are both plated for corrosion strength.
Connecting 2 wire 0,75 x 250 mm.
* The speed rotation can change of ± 10%.
The S1 load test was made using a 1,9 A corrent in the air with an increase of temperature of 70° C.
The S2 load test was made using a 3.6 A corrent in the air with a timing 5` ON 5` OFF with an increase of temperature
of 80° C max. The starting corrent is 14 A and cannot be mantained for more than 2".
Max forces which may act on the outlet shaft: Axial 30 kg, Radial 40 kg on the extremity of outlet shaft.
It is possible to apply an encoder.
|
|
MSF/MSF combined worm gear motors
Worm gear speed reducers type SF-MSF are a new generation of products developed by our company.
|
|
CONSTRUCTION FEATURES
• One-piece gear cluster
• High-quality spur gearhead
• Input pinion with balanced clamp collar
• Quick installation
• High reliability design
• High strength steels
• High shaft loading capacity
• Viton O-Rings sealed at each joint
• Sealed ball bearings
• High efficiency design
• All gears are heat treated
• NEMA mounting standards
• 2 year warranty
|
|
107 AC
115/230V PSC TEFC AC Design
AC Parallel Shaft Gearmotors: 207 AC
115V Shaded Pole Open Fan Cooled AC
115V Totally Enclosed Fan Cooled AC Design
Product Features
Castings: Zinc Die Castings
Lubrication: Grease
Gears: Phenolic High Speed and Hardened Steel Ball Bearings On Motor
Mounting: All Positions
Rotation: Reversible
Seals: O-Ring Type On Output
Agency Approval: UL & CSA
Other products
307 AC
115V Split Phase, Open Dripproof AC Design
407 AC
115V Split Phase, Open Dripproof AC Design
507 AC
115/230V PSC, TENV AC Design
|
|
AC synchronous geared motor with flat transmission ASM fG 05 or 20
|
|
|
|
