|
|
When you need to produce and control high pressures, forces and torques permanently for mobile applications, then there are some pre-conditions:
- robust, service-friendly technology
- small size
- low weight
- as flexible multiple use of a component as possible
- easy handling and operation
The KRACHT mobile hydraulic components meet these requirements exemplarily. A glance at the technical data will convince you.
|
|
When you need to produce and control high pressures, forces and torques permanently for mobile applications, then there are some pre-conditions:
- robust, service-friendly technology
- small size
- low weight
- as flexible multiple use of a component as possible
- easy handling and operation
The KRACHT mobile hydraulic components meet these requirements exemplarily. A glance at the technical data will convince you.
|
|
KF gear pumps are used for pumping a wide variety of
fluids.
KF gear pumps are distinguished especially by their wide
range of variants which are assembled as required on the
modular principle and also permit subsequent upgrade.
The pumps are also suitable for media with low lubricating
properties.
The standard housing sections are of grey cast iron.
The gear units are manufactured from high-strength
case-hardening steel, hardened and mounted in special
multi-compound plain bearing bushes.
The standard drive shaft is sealed by rotary shaft
lip-type seal.
All pump sizes incorporate helical tooth system.
This feature, combined with special gear geometry,
results in extremely low noise levels and reduced
pressure pulsation.
|
|
|
|
|
|
Rugged, durable, and built to perform. All things that Haight is pleased to say the large flow pumps can provide. Built for some of the most challenging applications including: chemical use, fuel transfer, oil filtration, lubrication systems, and more. With pump sizes ranging from 120-240 gpm, which compliments our existing line of 1-80 gpm, and multiple seal configurations - you can be sure Haight can provide a pump that will work for your application.
Some of the key features in these DIU Series pumps are: ductile iron housings, steel shaft and pinion gears, and iron rotor with multiple bearing materials. Shaft sealing will include packing seals, lips seals & multiple mechanical seal types, with elastomers to suit. Other features and options are available depending on
Specific needs and applications.
Other features include:
- Built in Shaft Seal Flexibility
- Reduced maintenance and wear due to less moving parts
- Close Coupled design eliminates mis-alignment and related failures
- “Gear within a Gear” design for quiet operation
- Direct Drive - speeds to 1800 RPM
- Relief valve
- Wear Sleeves
Haight Pump is pleased to offer over 75 years of pump design, manufacturing knowledge and experience. Our ability to provide the customer with reliable pumps, quality customer service, quick reaction time, and in house capabilities (Manufacturing, Engineering, etc) makes us a quality supplier in the pump industry.
|
|
|
Liquiflo Max-Series Gear Pumps are manufactured from 316 Stainless Steel or Titanium, and are available in both Sealed and Mag-drive configurations. These pumps feature Helical gears and relieved wear plates for smoother and quieter operation and intrinsic reduction of gear separation forces. Their unique and durable design will assure extended life in high-pressure pumping applications.
|
|
| ... products without technical information |
| |
KD Scientific Pumps are acknowledged as the industries highest valued solution for deliver precise and smooth flow in research, pilot plants and production applications.
A broad line of syringe pumps from the most basc to advance programmable pumps. They are easy to use, selectable user flow rates and volumes.
They use a glass/plastic/stainless steel syringes. Models available for 1 ul to 140 ml syringes.
High pressure pump for viscous fluids or other applications.
|
|
|
The EF- 2000 is a high pressure piston dosing pump with one or two injection heads and electronic regulation through an inverter. The avaliable heads goes from 500 L/H (132 GPH) to 2000 L/H (634 GPH).
|
|
| ... products without technical information |
| |
|
|
|
|
The VBN, VBN-DS line heavy duty process pumps, available in double-casing or wet pit configurations, are vertical multistage, diffuser type.
Pump components geometry, optimised through hydraulic, structural, thermal and dynamic F.E.M. analysis, lead to an high product reliability. Particularly to avoid seizures correlated to dangerous resonances, the F.E.M. dynamic analysis is carried out on all manufactured pumps taking into account the proper site operating conditions.
Closed type impeller with front and rear wear rings as well as balancing holes, to minimise the axial thrust.
Large eye single suction or double suction 1st. stage impeller to meet low NPSH requirements.
Deep stuffing boxes, designed in accordance to API 682 Std., suitable to accept any type of mechanical or packing seal.
Labyrinths and deflectors at either bearing housing to maximise protection against dirt.
A wide range of sizes and material combinations complete the variety of the offered product.
Main design features
Fully designed according to latest edition of API 610 Std.
Number of stages rangeable from 1 to 14.
Pump shaft in one or at the maximum two pieces, fully machined to respect the more restrictive run-out API limits.
Air fan cooling system provided on bearing bracket.
As a standard, the rotor axial thrust is supported by a duplex oil lubricated ball angular contact type bearings.
Renewable bushings are provided at all interstage casings and columns.
|
|
|
Universal pumps for domestic or municipal water supply systems, for clean non-explosive liquids without solid or abrasive substances, for agricultural irrigation and sports application, for civil and industrial use, boiler feeding and condensate systems and for high pressure washing plants.
|
|
|
|
|
|
Application
These are suitable for many applications such as Mine Drainage, Hydraulic Power Water Supply. Boiler Feed and other Pressure vessel charge duties, Pressure 'oil firing, High pressure spraying and Car Washing.
Design
The ME Series of Pumps are of Mono Block Multistage type, where the pump unit is directly mounted on the Motor Shaft. The intermediate stages (diffusers) are held between suction and discharge casings with tie bolts. The number of stages and length of shaft are arranged to suit the required head and pressure. Utilizing 60 years, experience in this field we have developed Impellers fabrication from Stainless steel. They have reduced water friction and are balanced, thus increasing the performance. The stuffing box is easily accessible for replacement of gland packing. Mechanical seal types are also available.
Specification
The Discharge body, pump cover, Diffuser, Pump support and Motor body are of Gray cast Iron, shaft of steel AISI 1050, Impeller of Brass and S.S. Enclosed type two pole motor with external ventilation single phase 220/250 volts 50 Hz capacitor type and three phase 400 volts 50 Hz is properly insulated.
|
|
Specifically designed for re-circulating service in reverse osmosis and other membrane systems. Equipped with balanced double shaft seal with buffer fluid ports on top and bottom for complete removal of air/vapor from seal chamber.
- Rated up to 700 psi maximum pump casing pressure (at
discharge)
- Maximum differential pressure 150 psi (based on water)
- Sanitary construction for food and dairy processing
service
- Large, long-life bearings with non-wearing labyrinth seals
- 316L stainless steel impeller and shaft; 17-4PH stainless
steel casing
- Motor flange adapter reduces coupling wear
|
|
The patented Roto-Jet pump has only two basic working parts a rotating case with a stationary pick-up tube mounted within it. Performance can be adjusted by changing speed and/or pick-up tube.
Features / Benefits
- High pressure without high speed.
- Flexible - performance can be adjusted by changing the pitot tube.
- Simple - only two basic working parts.
- Smooth, pulsation-free flow.
- Low pressure mechanical seal is easily maintained.
- Isolated bearing pedestal to minimize bearing contamination.
- Hydraulically stable along the entire performance curve and beyond BEP.
- Low minimum flow requirement.
- API design available.
- Single or double mechanical seal.
- Threaded or flanged connections.
- Materials of construction: Ductile Iron, Carbon Steel, 316 Stainless Steel, CA6NM, and CD4MCu.
- Super duplex and Hastelloy are also available.
- Oil lubricated bearings.
|
|
Flow rate: 80 Litres/min (21.1 USgallons/min)
Pressure up to 1.2 bar (17.4psi)
Features:
• Heavy duty robust design
• Stainless steel construction
• Long life DC motor
• Silent running
• Anti-clog impeller design
• Long life mechanical seal
• Single tool servicing
• ISO 8846 MARINE and USCG Regulations for Ignition Protection
• ISO 8849 MARINE Bilge Pump Standard
|
|
The Gorman-Rupp line of engine driven high pressure fire pumps delivers up to 156 PSI and 250 GPM. They are equipped with an exhaust primer. All units have a built-in check valve and include a discharge pressure gauge, brass hose adapters - NPT to National Standard Fire Hose Threads, and a suction strainer.
Specifications
Size: 1-1/2" (37.5 mm), 2-1/2" (62.5 mm)
Max Capacity: 260 GPM (16 lps)
Max Head: 360' (110 m)
Max Solids: 0.3125" (8 mm)
Materials of Construction: Aluminum
Horsepower: 13 HP to 23 HP
|
|
The Fyr Port series portable pumps arespecially designed for applications involving high pressure. Standard features include brass piston type hand primer, recoil starting, and an 8-horsepower two-cycle engine which offers high horsepower in a small package. Two different mounting options are available — skid(20FP-C8SK) or wraparound frame (20FP-C8FR). The complete pumping unit weighs in at a mere 50 pounds — ideal for one-man portability.
* High Pressure performance
* Compact very lightweight design
* High horsepower weight ratio
* One man portability
Optional hose package: Contains 100 feet of 1-1/2" fire hose, adjustable nozzle, tune up kit, and 2-cycle oil in a canvas carrying bag.
|
|
Series TC and TH have been especially developed to sapply internally cooled tools with coolant fluid.
Closed impellers provide optimal hydraulic efficiencies while minimizing power consumption.
Closed impellers
High pressure / no long chips
10 ... 600 l/min
30 ... 520 m
|
|
|
Fristam FM pumps have been specially developed for generating high pressures and for operation with extreme pressure loads. The pressure is increased by several successive pumping stages.
|
|
Suitable for applications where the flow required varies continuously or the pump operates against a closed discharge valve.
MODEL :- CWHA
Capacity:- 90 m3/h - 400 USgpm
Delivery head max:- 1900 m - 6300ft
Max speed:- 6800 rpm
Casing pressure:- 160 bar - 2320 psig
Lubrication :- oil
MODEL :- CWHG
Capacity:- 80m3/h - 350 USgpm
Delivery head max:- 780m / 2575ft
Max speed:- 4300 rpm
Casing pressure:- 85 bar - 1230 psig
Lubrication :- grease
FEATURES
- Wide operating range up and down the performance curve
- Complies with API 8th edition
- Complies with ATEX
- Pulsation free operation
- Seal only on suction side
- No contact between pumped medium and pump lubricant
- Ability to handle solids and gases
- Dry running capability
BENEFITS
- Handles wide variations in flow (from 20% to 110% of
BEP flow)
- Wide application in oil extraction and oil processing
- Suitable for Category 2
- Extended MTBF
|
|
Honda High Pressure pumps offer high pressure with lower flow. The best applications for these water pumps are where higher pressure is required, such as when using sprinklers or a nozzle.
WH15
This high pressure pump is powered by the GX120 Industrial Engine. This pump offers exceptional performance when higher pressure is required in applications such as using sprinklers or a nozzle.
WH20
This high pressure pump is powered by the GX160 Industrial Engine. This pump offers exceptional performance when higher pressure is required in applications such as using sprinklers or a nozzle.
|
|
Honda High Pressure pumps offer high pressure with lower flow. The best applications for these water pumps are where higher pressure is required, such as when using sprinklers or a nozzle.
WH15
This high pressure pump is powered by the GX120 Industrial Engine. This pump offers exceptional performance when higher pressure is required in applications such as using sprinklers or a nozzle.
WH20
This high pressure pump is powered by the GX160 Industrial Engine. This pump offers exceptional performance when higher pressure is required in applications such as using sprinklers or a nozzle.
|
|
High pressure diaphragm pump units are used for the zero-leakage handling of hazardous, toxic and difficult media. State-of-the-art design features ensure high operating safety, economy and availability. They are characterised by their space-saving construction and flexible drive variants.
- Pressure max: 350 bar
- Capacity max: 850 l/min at 120 bar
250 l/min at 350 bar
- Power: 250 kW
- Weight: 10 t
|
|
ALMATEC's high-pressure diaphragm pumps have been specially developed for charging filter presses with chemical wastes and special sludge.
With a driving pressure of max. 7 bar, the pumps of series AH build up a delivery pressure of 16 bar on account of the internal pressure boost. These genuine double-action pneumatic diaphragm pumps are available in three sizes with a maximum delivery volume of 4 m³/h (AH 15), 10 m³/h (AH 25) and 20 m³/h (AH 40).
All housing parts in contact with the product are made of PE UHMW. This polymer material is seven times more resistant to abrasion than PP. PE is also more resistant to wear than cast iron, aluminium and even steel.
|
|
• Available pressures up to 150 psi (10.3 bar)
• Pump is sealed in corrosion resistant material, thus offering unparalleled performance and life
• Bypass System eliminates pulsation and cycling
• Latest co-injection mold diaphragm technology virtually eliminates potential leak paths
• Wetted materials designed to withstand many corrosive chemicals*
• Variable Speed Drive optional
|
|
Hypro high pressure diaphragm pumps are recommended for spraying of herbicides, pesticides, liquid fertilizers and many other hard to handle fluids. Low-cost maintenance and almost wear-free operation make these pumps ideal for a wide variety of spraying jobs.
Pressure and output are designed for optimum performance of medium to large-sized sprayers. Hypro high pressure diaphragm pumps are supplied with single or double-splined through-shafts. Pumps include pulsation dampeners.
Performance Information
- Max. flow: 21.4 gpm/81 lpm
- Max. pressure: 725 psi/50 bar
- Max. rated speed: 550 rpm (D813); 3600 rpm (D813GRGI)
- Max. fluid temperature: 140°F/60°C
|
|
EH2-M
These air-powered, single diaphragm metallic pumps deliver discharge pressure twice the inlet pressure, up to 250 psi (17 bar). Designed for filter press feed or similar applications requiring higher discharge pressures.
Pipe Size: 2" / 50mm
Displacement Per Stroke: .22 gal / .83 ltr
Max. Flow per Minute: 25 gal / 95 ltr
Max. Solids Handling: .25" / 6mm or 2" / 50mm
Max. Discharge Pressure: 250 PSI / 17.2 BAR
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
