|
|
G4 Standard Electric is Powered by a 115V - 60HZ, 1-1/2 hp induction motor (1,725 rpm); low startup voltage, draws 16 amps at full load (230V models available).
G4 Gas pump is powered by a 4 hp Briggs & Stratton gas motor.
Electric models are equipped with a 15’ remote power controlled pendant.
Reservoirs available in 1.5-20 gallons; welded steel designs.
Recommended for mid-sized or multi-tool operation - 55 cu.in. flow group
Ideal for remote service application or in-plant production applications requiring quiet – continuous cycling
|
|
KF gear pumps are used for pumping a wide variety of
fluids.
KF gear pumps are distinguished especially by their wide
range of variants which are assembled as required on the
modular principle and also permit subsequent upgrade.
The pumps are also suitable for media with low lubricating
properties.
The standard housing sections are of grey cast iron.
The gear units are manufactured from high-strength
case-hardening steel, hardened and mounted in special
multi-compound plain bearing bushes.
The standard drive shaft is sealed by rotary shaft
lip-type seal.
All pump sizes incorporate helical tooth system.
This feature, combined with special gear geometry,
results in extremely low noise levels and reduced
pressure pulsation.
|
|
When you need to produce and control high pressures, forces and torques permanently for mobile applications, then there are some pre-conditions:
- robust, service-friendly technology
- small size
- low weight
- as flexible multiple use of a component as possible
- easy handling and operation
The KRACHT mobile hydraulic components meet these requirements exemplarily. A glance at the technical data will convince you.
|
|
When you need to produce and control high pressures, forces and torques permanently for mobile applications, then there are some pre-conditions:
- robust, service-friendly technology
- small size
- low weight
- as flexible multiple use of a component as possible
- easy handling and operation
The KRACHT mobile hydraulic components meet these requirements exemplarily. A glance at the technical data will convince you.
|
|
|
|
|
|
Rugged, durable, and built to perform. All things that Haight is pleased to say the large flow pumps can provide. Built for some of the most challenging applications including: chemical use, fuel transfer, oil filtration, lubrication systems, and more. With pump sizes ranging from 120-240 gpm, which compliments our existing line of 1-80 gpm, and multiple seal configurations - you can be sure Haight can provide a pump that will work for your application.
Some of the key features in these DIU Series pumps are: ductile iron housings, steel shaft and pinion gears, and iron rotor with multiple bearing materials. Shaft sealing will include packing seals, lips seals & multiple mechanical seal types, with elastomers to suit. Other features and options are available depending on
Specific needs and applications.
Other features include:
- Built in Shaft Seal Flexibility
- Reduced maintenance and wear due to less moving parts
- Close Coupled design eliminates mis-alignment and related failures
- “Gear within a Gear” design for quiet operation
- Direct Drive - speeds to 1800 RPM
- Relief valve
- Wear Sleeves
Haight Pump is pleased to offer over 75 years of pump design, manufacturing knowledge and experience. Our ability to provide the customer with reliable pumps, quality customer service, quick reaction time, and in house capabilities (Manufacturing, Engineering, etc) makes us a quality supplier in the pump industry.
|
|
|
Haight offers five sizes of pumps in the Double pump series. Available with a variety of optional seal, bearing and rotor materials. The Double Series offers exceptionally compact design, plus low shear and noise characteristics. Compact, rugged and simple, these pumps are ideally suited for close-coupled mounting, which eliminates the need for expensive gear boxes, and prevents coupling alignment problems.
|
|
Haight offers six sizes of pumps in the square flange U-Series. All sizes are available with a bolt-on Relief Valve which can function in either a return to suction, or return to tank mode. All U-Series pumps are interchangeable with earlier D & DR Series pumps.
Compact, rugged, and easy to maintain, these pumps are ideally suited to close-coupled mounting to the motor or footed mounting. Haight Pumps bolt-on footed brackets match standard NEMA motor height eliminating pump or motor shimming. Each bracket size is designed to align the pump and motor shaft heights without shim blocks.
|
|
|
Haight offers six sizes of pumps in the round hub U-Series. All sizes are available with an optional bolt-on relief valve which can function in either the return to suction, or return to tank mode. Compact rugged, and easy to maintain, these pumps are ideally suited to close-coupled mounting, or direct mounting to the motor...
|
|
|
The Jacketed Universal Seal series heavy duty internal gear pumps feature jacketing in the bracket and head or relief valve for rapid melting of solids before startup. Available in cast iron, ductile iron, steel or stainless steel, they handle a broad range of liquids and process applications. These pumps offer a unique seal chamber capable of accepting shaft packing, component-type single and double mechanical seals, cartridge-type single and double mechanical seal and triple lip seals. A broad selection of port sizes and orientations (90- and 180-degree ports) allows easy installation. ATEX conformity available.
|
|
|
With five series, including 30 displacements, Viking Pump offers the broadest line of industrial lobe pumps in the world. Providing low shear, high efficiency and pressures to 27 bar, these stainless steel pumps offer a broad variety of rotor forms and shaft sealing options. They can handle liquids from 1 to 440,000 cSt. They are designed to handle steam or solvent-cleaning between batches.
|
|
|
The High-Speed Compact internal gear pumps offer heavy-duty design and small footprint for rotating equipment lubrication such as compressors and turbines. They are just one of many options that Viking offers for lubrication pumps. Others include gearbox lube pumps that pump in one direction regardless of shaft rotation, pump kits for OEM lubrication applications, and a variety of internal gear, external gear and gerotor pumps suitable for lube oil and grease applications,
|
|
|
Viking Mag Drive® sealless internal and external gear pumps eliminate leakage and maintenance associated with shaft seals. For use with all hazardous/toxic fluids, hard-to-seal liquids and for 24/7 operations which cannot afford unscheduled downtime due to seal failure. Some models allow reversible direction of flow, and temporary run-dry capability. May be close-coupled to IEC or NEMA motors, or long-coupled with optional bearing carrier. ATEX conformity available.
|
|
|
Designed to operate at 50 hz motor speeds to eliminate need for a gear motor or reducer, these ductile iron internal gear pumps are well suited for chemical processing, grain processing and petroleum products. They may be foot mounted or close-coupled to IEC motors. The DIN seal chamber accepts many types of shaft seals.
|
|
|
|
|
|
|
The CMD series is a groundbreaking new series of sealless, non-metallic pumps specially designed for crucial liquid containment applications. This series offers several important benefits, including: 100% renewable performance with use of Viking’s recommended spare parts kit; an innovative magnet system with a patent-pending spline design that allows the magnet to self-align while floating on the shaft with no added fasteners; self-lubricating, heavy-duty bearings with patent-bearing geometry that allow dry-run capabilities; and, a unique, universal flange that allows for easy installation for both ANSI and DIN flanged systems, among other key benefits. In addition, the CMD series offers extreme flexibility, including an array of models with port sizes ranging from .25” to 1.5” (6.35 to 38.1 mm), a performance level of 100 SSU (22 cSt), normal capacity at 1450 RPM ranging from 0.34 to 30 GPM (1.3 to 120.0 LPM), normal capacity at 1750 RPM ranging from 0.4 to 33.0 GPM (1.5 to 125.0 LPM), a maximum differential pressure of 150 PSI (10 Bar), a maximum hydrostatic pressure of 200 PSI (14 Bar), approximate shipping weights ranging from 4 to 44 pounds (2 to 20 kg), and a maximum recommended operating temperature of 150°F (65°C).
|
|
|
Fully jacketed Universal Seal series heavy duty internal gear pumps for monomers and polymers such as ABS resin, epoxy resin and polyester, provide even temperature control throughout. With a variety of sealing options and many port options, including top suction/bottom discharge for reactor pumping, these pumps are widely used in place of conventional external gear pumps which require two more sleeve bearings than these internal gear pumps do. ATEX conformity available.
|
|
|
The Universal Seal series heavy duty process pumps are internal gear pumps offering exceptional durability and ease of maintenance. Available in cast iron, ductile iron, steel or stainless steel, they handle a broad range of liquids and process applications. These pumps offer a unique seal chamber capable of accepting shaft packing, component-type single and double mechanical seals, cartridge-type single and double mechanical seal and triple lip seals. A broad selection of port sizes and orientations (90- and 180-degree ports) allows easy installation. ATEX conformity available.
|
|
|
|
|
|
The SteriLobe® series offers the ultimate in modular, flexible design to ensure that the appropriate feature set is provided for every application. The pump can be configured to handle nearly every unique pumping problem.
Product Features:
Easy accessibility to seal area enhances cleaning and CIP capabilities.
Generous seal access facilitates simple front loading and removal of seal, even for flushed and double options without stripping the pump.
Cover joint profile improves hygienic characteristics and self-draining capabilities.
Rugged gearbox construction enables the carrying of radial loads.
Stainless gear cover and electro-less nickel plated bearing housing provide clean and corrosion resistant external finish.
Mounting Options: The SteriLobe® range has cast stainless steel bolt-on feet which offer stable and robust support to the pump with the advantage of corrosion resistance. This enables the pumps to be mounted with shafts in the upper or lower position and for ports to be aligned horizontally or vertically.
Rotor Options: 316 SS Bi-Wing or Multi-Lobe rotor options offer clearances to 300°F (150°C), making them suitable for all CIP and SIP conditions. Closer tolerance rotors are also available for low viscosity / higher efficiency applications, and Multi-Lobe rotors are also available in non-galling Alloy 808.
|
|
|
|
|
|
|
The RTP20 (1.0 liter/rev) and RTP30 series (1.28 liter/rev) design is a proven high-speed rotary transport pump with exceptional performance, advanced durability, application flexibility, and ease of installation to help users achieve enhanced productivity for a lower total cost of ownership. This series’ tri-lobe design, customizable per customer specifications, is compact and light-weight and features removable feet and multiple mountings for easy vertical or horizontal adaptation. Both the RTP20 and RTP30 series efficiently fill rotor voids, allowing for faster and quieter operation on viscous liquids. In addition, with a longer sealing land at rotor tips, the series provides enhanced efficiency when working with lower viscosity products. The RTP20 offers a capacity to 264 GPM (1,000 L/M / 60 M³/Hr.), pressure to 145 PSI (10 Bar), viscosity to 250,000 SSU (55,000 cSt), and operates in temperatures to +230°F (+110°C). The RTP30 offers a capacity to 340 GPM (1,283 L/M / 77 M³/Hr.), pressure to 175 PSI (12 Bar), viscosity to 250,000 SSU (55,000 cSt), and operates in temperatures to +300°F (+150°C). These pumps are available with ACME threaded or tri-clamp ports as well as many other port connection types.
|
|
KF gear pumps are used for pumping a wide variety of
fluids.
KF gear pumps are distinguished especially by their wide
range of variants which are assembled as required on the
modular principle and also permit subsequent upgrade.
The pumps are also suitable for media with low lubricating
properties.
The standard housing sections are of grey cast iron.
The gear units are manufactured from high-strength
case-hardening steel, hardened and mounted in special
multi-compound plain bearing bushes.
The standard drive shaft is sealed by rotary shaft
lip-type seal.
All pump sizes incorporate helical tooth system.
This feature, combined with special gear geometry,
results in extremely low noise levels and reduced
pressure pulsation.
|
|
|
|
|
|
Pump series BT and BTH are low speed gear pumps for
transfering medium and high viscosity fluids, provided they
have certain minimum amount of lubricating property, do
not contain any solids and are chemically compatable with
the materials of construction.
The standard material of construction for housing, bearing
cover and stuffing box cover is grey cast iron. The shafts
and gears are manufactured from case hardening steel, hardened
and ground. The shafts are carried in plain bearings
manufactured in bronze, with an option of sintered iron.
The rotary shaft seal is a packed gland consisting of PTFE
fillied Aramid yarn, and the static sealing between mating
parts is by means of either, liquid sealant or gaskets. All
sealing materials are asbestos free.
External axial loads are not permissable, restricted radial
loads can be absorbed, dependant on their magnetude and
direction.
Driving by flexible shaft coupling is preferred.
In the case of fluids which require elevated temperatures to
flow i. e. bitumen, wax etc. the BTH series pump should be
used. In this model the housing is double walled to provide
a heating jacked. The pump transfer chamber is heated by
circulating heat transfer fluid or steam through the jacket.
|
|
KF gear pumps are used for pumping a wide variety of fluids.
KF gear pumps are distinguished especially by their
wide range of variants which are assembled as required
on the modular principle and also permit subsequent
upgrade.
The pumps are also suitable for media with low lubricating
properties.
The standard housing sections are of grey cast iron.
The gear units are manufactured from high-strength
case-hardening steel, hardened and mounted in special
multi-compound plain bearing bushes.
The standard drive shaft is sealed by rotary shaft lip-type
seal.
All pump sizes incorporate helical tooth system.
This feature, combined with special gear geometry,
results in extremely low noise levels and reduced
pressure pulsation.
|
|
Flow rate: Nominal 25 Litres/min (6.5 gallons/min)
Self-priming from dry up to 1m (3ft)
Features:
• Maximum viscosity 150Cs
• Inlet Filter Included.
• Simple design means fewer wearing parts.
• Ideal for water, oil and diesel transfer.
• Meets USCG 183.410
• ISO 8846 MARINE (Ignition protection)
|
|
High Pressure Gear Pumps
Lynch gear pumps are available in six different groups (0.25, 0.5, 1P, 1, 2 and 3). Different pump displacements within each group, ranging between 0.011 cu. in./rev and 5.310 cu. in./rev, can be obtained by changing the thickness of the gear tooth band. Within the same group, different flanges, shafts, inlet and pressure ports are available.
The following items are also available:
- pumps with integrated maximum pressure valve;
- hi-pressure pumps
- bi-rotational pumps
- hydraulic motors (both unidirectional and bi-directional)
- modular multiple pumps.
|
|
Conventional sealing gaskets are pushed to their limits with
different applications. Typical applications are found in
polyurethane facilities, refrigerating machines and vacuum
facilities. For these applications, you have the possibility
to equip the KF 4…80 with a magnetic coupling.
The magnetic coupling serves as a shaft seal and for the
transmission of the torque. The outer rotor of the magnetic
coupling is assembled on the engine shaft and the inner
rotor is assembled directly on the pumping shaft. The
torque is transmitted through the magnetic forces between
the outer and inner rotor. Between the two rotors, you
have the split case which hermetically seals the pump.
|
|
N Series Gear Pumps
One of our most successful projects, N-series is designed for metering and transfer of a great variety of fluids in any industrial application, but usually they operate as metering pumps for bitumen on bitumen plant. This series is the best choice for any petrochemical application since 1990.
Materials
Housing: Cast Iron G25
Rotors: Steel 39NiCrMo3
Bearings: Bronze
Sealing Elements: Various
Application
Viscosity: from 1CST to 1'000'000CTS
Pressure: from 0BAR to 15BAR
Size: from 460cc/rev to 1330cc/rev
Temperature: from -10°C to +240°C
|
|
Single or Multiple configurations
Flows to 29 gpm @ 2400 rpm with pressures to 3000 psi
Motors up to & over 40hp
|
|
|
Gear pumps of the TF series are particularly suitable for pumping all media which guarantee a minimum lubricity but do not contain any solids. The sense of rotation in TF pumps is normally clockwise as seen from the pump shaft. Upon request the pumps can be supplied with counter-clockwise rotation or with clockwise and counter-clockwise rotation with alternating direction of delivery flow. The nominal bores of suction and pressure ports are optimally dimensioned in order to limit the oil speeds to about 5 m/s max. at the standard rotational speed.
|
|
|
|
|
|
C-KLR ZEPHYR
Volume flow: 80 - 140 m³/h
Overpressure: +1.0 bar
Vacuum: -0.6 bar
With the innovative, dry-running C-KLR ZEPHYR multi-claw range from Elmo Rietschle, pressure and vacuum can be combined in a single claw stage. All operation points on pressure and suction side work almost independently from each other. The C-KLR ZEPHYR operates economically and highly efficiently thanks to the patented triplelobe design with intermediate charging of air. This new design reduces pulsation in the pipes connected to the pump, and keeps the noise level low. An integrated cooling system for compressed air allows operation in applications, where compressed air
temperatures are of importance.
Advantages:
- High efficiency, dry and frictionless compression
- Low maintenance
- Integrated air cooling without additional cooling medium
- Suitable for multiple applications
This series is also available as vacuum pump (C-VLR ZEPHYR) and compressor (C-DLR ZEPHYR).
Typical Applications:
Printing & Paper, Chemical, Environmental, Packaging, Pneumatic Conveying, Woodworking
|
|
The Mink rotary claw pumps were developed especially for use in industrial applications where constant vacuum or pressure is required, along with totally oil free compression. Mink vacuum pumps or blowers are used in all applications, which require oil-free vacuum or oil-free compressed air.
The Mink is available as a single-stage or two-stage vacuum pump.
Features
* Non-contact operation
* No maintenance
* High efficiency
* Many different sizes and models
* Speed control (option) · ATEX certified (option)
* Version for oxygen delivery
Application
Ideal for use in various industries such as Plastics, Printing and Paper, Food, Beverage, Wood, Pneumatic Conveying, Brick Making, Adsorption and Degassing, Environmental Technology, Metallurgy, Remediation and many more.
|
|
Lubricating pumps for marine gearboxes. Gearbox driven direct coupled pumps. Auxiliary lubricating pumps with electric motor drive
Metering pumps for polyols with abrasive fillers with separate bypass valves
Gear pump for hot oil circulation - special design
Metering pump for the polyurethane industry with integral pressure limiting valve, seal chamber and geared servomotor as a complete unit
|
|
|
|
