|
|
Features:
robust cast iron housing
gearing meets up to date international high standards
wide selection of motors and brake-motors including inverter-duty motors
units available for harsh environments
integrally cast foot or flange designs
sleek design for easy cleaning
all bearings selected to provide long and trouble-free operation
high quality sealing for enhanced leakage-protection
output side is integral part of the housing, no bolt-on output cover to cause leakage or gear-misalignment
|
|
Spur Gearheads
Compactline, for extremely quiet and high-performance drive applications.
Flatline, with the same approved properties as the Compactline but extra flat, making it ideal for limited space situations
|
|
SEW-Eurodrive's R-Series parallel gearmotors deliver exceptional performance and reliability combined with low maintenance. Available in many configurations, they continually distinguish themselves with their efficiency and durable gearing.
- Reducers
Gears manufactured from certified steel, heat treated to a case hardness of 58-62 Rockwell C for long gear life
Finished ground or shaved gear teeth to assure maximum mechanical efficiency (1-1/2% loss/gear stage), minimum noise and heat generation
High capacity anti-friction bearings for optimum load carrying capacity and long life
Captured keys on output shafts
Gearcases are made of high-strength, gray cast iron, SAE Class 30; R27 and smaller are made of high-strength, pressure-cast aluminum
High cross-section modulus design, with center wall for maximum rigidity
Center tapped holes on output shafts
Double output seal design consisting of patented bi-helix inner seal made of Viton® and double-lip Nitrile (Buna-N) outer seal*
-Motors
NEMA Design B/C
Inverter duty
Connection terminals
Extremely low motor inertia
Mark for shipment into Europe
|
|
The gear boxes with ASR unlock device are supplied with the wormwheel of spheroidal-graphite cast
iron GS500 - fully dimensioned in the majority of intermittent applications for sliding door and gate driving,
but with different torque values from those shown in the relevant catalogues RS and RT.
A bronze wormwheel is supplied on demand for those cases where the requested torque or duty cycle
are particularly severe.
|
|
Uniblock design for foot and flange mounting. Gear case machined on all sides for universal application.
Revolutionary new gearing geometry here and in all the other models results in exceptional running smoothness. For special environmental conditions the gear unit can be fitted with two shaft seals.
|
|
ASTRO gear motor with flat transmission ASM SG01
|
|
ASTRO synchronous motor with Stirnradgeriebe ASM SG
- starting and direction of rotation-stably
- synchronous, load-independent number of revolutions
- blockierfest briefly
- 1-polig reversable
- high efficiency
- noiseless run
- high self retaining moment
- maintenance-free
Overall lengths
ASM 24/26 SG = 89,5mm
ASM 44/46 SG = 109,5mm
ASM 84/86 SG = 149,5mm
Terminal box execution = 33mm longer
Engine system
4-polig with 1.500Upm (50Hz), 1800Upm (60Hz)
with 6 pins with 1.000Upm (50Hz), 1200Upm (60Hz)
Rated voltages = 1~24V to 3~500V
Continuous operation S1 (special modes of operation possible)
Self retaining moment in the dead condition
Wärmeklasse B
Coil windings = to 130°C
Ambient temperatures = -15C to 40°C
Enclosure = IP40, IP54, IP55
Basic parts = plastic or aluminum pressure pouring
Kind of connection = cable, braid or terminal box connection
|
|
Benefits of ABM helical geared motors
Helical geared motors are the most commonly used industrial gearboxes. They efficiently increase motor torque while reducing motor speed to a
favorable range.
Key features of ABM helical geared motors:
%u2022 Energy conserving operation at 98% efficiencies per stage
%u2022 Outstanding value at competitive prices
%u2022 Robust and maintenance free
%u2022 Very low emission operation compared to com-bustion engines and hydraulic or pneumatic drives
High quality helical gearing with ground gear tooth flanks that guarantee quiet operation and precise torque transfer.
Applications
%u2022 Material handling, cranes and hoists
%u2022 Textile production
%u2022 Construction industry (elevators, pumps)
%u2022 Packaging industry
%u2022 Sheet metal fabrication
|
|
Technical Description. Motor casing: Deep drawn, corrossion protected. Excitation field: Permanentmagnet. Method of bearing, A-side: Ball bearing, sleeve bearing optional. Method of bearing, B-side: Sleeve bearing. Gear: Worm gear.
Gear housing: Aluminium die cast. Gear wheel: plastic. Gear greasing:
Lubricant/permanent lubrication. Mechanic interface: Output shaft. Electric interface: Connector.
|
|
| ... products without technical information |
| |
The new SMAT continuously detects the position of the cylinder piston within a range of 50 mm. It has an analogue output with an output signal in proportion to the piston position. The integrated OOR (out-of-range) sensor indicates if the piston is outside the sensing range. The connection for evaluating the 0 … 10 V and/or the 4 … 20 mA signal is made directly to analogue inputs.
Typical areas of application in object detection are as follows:
Press-fitting, clamping, position sensing, workpiece replacement
In process monitoring:
Sheet metal handling/production, wear monitoring, quality inspection
- The installation direction of the SMAT in the slot can be chosen freely.
- Contactless measuring principle = wear-free sensing.
- Measuring range is always 50 mm, regardless of cylinder; reproducibility 0.1 mm.
|
|
Position Sensing Solutions
Bimba offers pre-tested Position Sensing Solutions for Bimba actuators. Our solutions provide a cost effective interface between the pneumatic actuators and electrical control systems. Our pre-tested solutions also eliminate costly, time-consuming design and fabrication required if switches are purchased separately and provide an aesthetically pleasing installation.
Both traditional Bimba switches as well as newer generations of Bimba switches are offered to allow for maximum flexibility to fit your application.
The switches perform the same functions as conventional limit switches. They can be used as position indicators, cycle counters, or to confirm operation.
All Bimba switches are designed to sense a magnet that is incorporated into the piston of the cylinder. Magnets are standard in Bimba MRS cylinders, but must be purchased as an option on other Bimba actuators.
A variety of outputs are offered for each switch family including PNP (transistor sourcing), NPN (transistor sinking), normally open contacts, and higher power triac.
|
|
|
Our huge standard programme with its diversity of housings has the optimal solution for almost any application. The various types of clamp or the dovetail connections directly integrated into the switch mean that the switches can be fitted on almost any type of cylinder. Our range also includes pneumatic cylinder switches for T-section cylinders. All the models can be supplied with dry reed contact with variable power capacities or in the electronic version. If you wish, we can develop completely new customer-specific sensors to meet your requirements.
|
|
|
In all automated processes the use of sensors to provide information for the plc is of prime importance. Sensors supply the necessary signals on positions, end stops, levels or serve as pulse transmitters for counting jobs or for monitoring rotational speed. In industrial usage inductive and capacitive proximity switches are indispensable. As compared to mechanical switches they offer almost ideal conditions: non-contact, maintenance-free operation, high switching frequencies and switching accuracies as well as high protection against vibration, dust and humidity. Inductive sensors detect all metals without contact, capacitive sensors detect nearly all solid and liquid media such as metal, glass, wood, plastic, water, oil, etc..
|
|
The RACO path-sensory system has been specially designed for exactly positioning and switching off electro-magnetic actuators in the final position. Not only is the position ascertained unconventionally by electro-magnetic means (e.g., gear-shifting mechanism) while doing so but it will also be determined via a close-coupled magnetic field without any movement.
The EPS consists of a printed circuit board and a magnetic holder with the magnet. The electronic positioning sensor (EPS) is integrated into the device%u2019s supplementary casing (A) on the motor shaft's end of the servo-motor or in the device's supplementary box (D) on the coupling casing. The installation, commissioning (starting up), maintenance (servicing) and upgrading is simplified in comparison with a conventional design that has mechanical limit switches and a shift transmission which must be adjusted individually.
|
|
Features
All-electronically or reed contact
MZEK... can be fitted from above
MZ C... for Cylinders with 4 mm round slots
Absolutely wear-free
High reproducibility
Metal Case
Connecting Cabel 2,5 m (5 m) PUR or 0,3 m (0,6 m) PUR with knurled connector M8
Bright LED
Short-circuit-proof
Polarity-safe
Protection class IP 67
|
|
One sensor, two adjustable switching points
Saves space, time and money
Simple alignment and definition of the switching point thanks to teach process
Easy mounting with only half the cabling work
Sensor sunk into the T-slot thanks to compact design
Applications: end position query to short hoist cylinders or intermediate position detection, e.g., for reducing piston speed
|
|
|
MODEL WORKING DIMENSIONS HANGER LOAD HANGERS O mm H mm kg N TURBORAIL 1 800 1100 500 14 16 TURBORAIL 1 600 1100 500 19 TURBORAIL 2 1000 1500 700 16 18 HANGER MODELS WITH AUTOMATIC CONTINUOUS OR INDEXING WORKLOAD ADVANCEMENT
|
|
For gas and oxygen cylinders blasting equipment is used to blastclean the insides during production and remove corrosion such as rust and scale during rebuilding.
Cylinders are positioned in the blasting stations either manually or by means of lifting gears and roller conveyors or by robot (see illustration above).
Cylinders are processed vertically to ensure that abrasive gravitates downwards.
|
|
| ... products without technical information |
| |
Designed specifically for use in hydraulic and pneumatic actuator applications, where the sensor is fitted inside the pressurised environment.
Available in a choice of two mounting styles (Internal or External), these sensors can be supplied in lengths to suit actuator strokes up to 1100mm.
|
|
Designed specifically for use in hydraulic and pneumatic actuator
applications, where the transducer is fitted inside the pressurised
environment. Can operate at pressures of 670 Bar and temperatures of +200C.
Seperate electronics module operates from 10-60Vdc.
Available in a choice of mounting styles (Internal or External), these
transducers can be supplied to suit actuator strokes up to 2000mm.
|
|
WaveScale Linear Displacement Transducers are an enhancement of the Series 2HX Electrohydraulic Actuators. Cylinders with the WaveScale meet standard NFPA heavy duty hydraulic cylinder dimensions, 2” to 6” bore with a male piston rod end. The main advantage is no false stage is required for cap mounts. The overall length of the cylinder is not increased!
3000 PSI Operating Pressure
Non-Linearity: ±0.02% of cylinder stroke or
±0.004 inch, whichever is greater.
Repeatability: Equal to resolution
Input Voltage: +24 VDC
Standard Operating Temperature: -40° F to 185° F.
Cylinder Stroke Length: Up to 100 inches.
Multiple Output: Analog - Voltage or Current
Digital - Start/Stop or PWM
|
|
| ... products without technical information |
| |
Material : St 52 bk + s, St 52.0
St 52-3N, StE 460 nbk ::Tol. OD DIN 2391; 2448
Tol. WD DIN 2391; 2448
Tol. ID ISO-Tolerance Field H8 - H11
Center Line Average of Interior Surface honed Ra max. 0,5 µm
roller burnished Ra max. 0,4 µm
Dimensional Range: ID ø20 - 500 mm, larger dimensions on request
|
|
| ... products without technical information |
| |
|
|