|
|
| ... products without technical information |
| |
Three-phase geared motors
Popular geared motors with constant speed and high functionality; power range 0.06 to 45 kW; output torques of up to 9,000 Nm
Detailed information
Geared motors - inverter variable speed drives
Popular industrial geared motors combined with electrical adjustment via 8200 motec frequency inverter; power range 0.25 to 7.5 kW; the distributed drive solution
Detailed information
Geared motors - electronic starter
Popular industrial geared motors combined with the electronic starter starttec; power range 0.25 to 4.0 kW; the distributed drive solution
Detailed information
Geared servo motors
Highly dynamic geared servo motors with synchronous and asynchronous servo motors; max. torque: 7 - 9,000 Nm; low backlash
Detailed information
Gearboxes - with shaft or flange input
Speed reduction gearboxes with free shaft or IEC flange at the input side suitable for motors to IEC 72; output torques of up to 9,000 Nm; finely stepped output speeds
Detailed information
Geared motors - mechanical belt adjustment
Popular industrial geared motors combined with mechanical adjustment via Simplabelt compact units; power range 0.25 to 45.0 kW; adjustment range 1:6
Detailed information
Geared motors - mechanical adjustment Disco
Popular industrial geared motors combined with mechanical adjustment via Disco variable speed drive; power range 0.25 to 7.5 kW; adjustment range 1:6
Detailed information
Disco variable speed drives
Mechanical adjustment with Disco variable speed drive; power range 0.25 to 7.5 kW; adjustment range 1:6
Detailed information
Standard three-phase AC motors
Standard three-phase AC motors; 0.25 to 22.0 kW 3 x 230/400 V; enclosure IP 54; mountings B3, B5 or B14; these motors are optimised for operation with a frequency inverter
|
|
FC750 is a very simple, yet efficient Plug & Play frequency converter for the growing market in simple speed control of 3 phase asyncronous AC motors. The FC750 has been specifically developed for the continuously demanding market involving seamless speed control of especially Fans, pumps, ventilators and any simple AC motor application FC750 is an totally integrated and encapsulated frequency converter, with a very simple Interface,, and a very sophisticated set of fault control systems, that will ensure the motor to RUN, even in extreme conditions. The IP54 or higher cabinet will ensure that there will be no need for an extra Cabinet, as usually with FC´s. The integrated EMC filter in the FC750 makes it an ideal solution for many applications, where Plug & Play is a first issue. No need for an external filter, no need for an exernal cabinet, no need for any "irritating" setup menus,, just plug it in, and you have a motor that spins as nice as with any other converter.
FC750 has as standard a 0-10 / 2-10V input control range with an auxilary START/STOP signal. Just a wire to the Gnd to make it spin. Also, there is an extra signal, that could make the motor turn in the opposite direction, just connect DIR to Gnd,, if it is needed. FC750 also has an "inbuild" motor protection, that will ensure that motors do not get overheated. The function can be adjusted in 9 steps from the Dipswitch. DIP=0 means NO protection. FC750 will stop the motor and activate the ALARM relay when current has been exeeded for ten times.
FC750 is not the controller for machinery etc, but is meant as a highly integrated power device for small AC motors. Fans, Pumps etc will benefit of this compact Controller. Also, applications requiring simple installation and a high grade of encapsulation will have to contact Motron for more info.
|
|
... see all the products in the category
AC drives
|
Application:
•Decentralized motorization of loads < 500kg (cardboard boxes, trays, totes…) for conveying systems where there is no risk of accumulation
•Regulation for speed in gravity roller conveyors, access gate, bridging between conveyors, 90° transfers, powered roller bends…
•Applicable to all industries (automotive, electronics, mail …) for assembly lines and transfers
Benefits:
•Safety (no exposed transmissions)
•Comfort/Ecological (without oil bath)
•Modular & flexible conveyor zones
•Space saving
•Quick and simple installation removing the need for maintenance (no exposed transmissions)
Concept and characteristics:
•The AC asynchronous motor and the life lubricated planetary gears and bearings are integrated inside the roller tube to drive the loads directly
•Internal shock absorber protects the gearbox
•Continuous or intermittent duty cycle (720 start-stop/hour)
•Speed from 4 to 50 m/min
•IP54, 55 and 65, clean room
•1phase or 3 phase, 50 or 60Hz, from 100 to 440V
•option : accumilation motor or brake motor
AC 1phase & 3 phase range:
•Ø 50 standard: series K
•Ø 57 standard: series A
•Ø 60.5 standard: series B |
|
| ... products without technical information |
| |
|
|
