|
|
Mineral Processing
Limekiln
Germany
1x impact hammer mill PHM1012
rotor diameter 1000 mm
rotor width 1200 mm
input 6.3 mm
output 0.8 mm
limestone 60 t/h
|
|
|
Laboratory roll mills are machines for testing the quality and processing characteristics of polymer material by means of discontinuous plastification, mixing or kneading. In both, plastics and rubber processing as well as processing of ceramics or special materials, roll mills by Dr. Collin are setting new standards in terms of precision and reliability.
|
|
Mineral Processing
Building material plant
Russia
1x roller mill WM1012
rotor diameter 1000 mm
rotor width 1200 mm
input 5-20 mm, 5-40 mm
output <8 mm
limestone
clay 60 m³/h
|
|
The number one solution for compacting your EPS (Expandable Polystyrene) minimum 20:1 measured on weight.
Mil-tek EPS Model 900:
• Capacity: 15 kg. per hour
Mil-tek EPS Model 1800:
• Capacity: 80 kg. per hour
|
|
DELITEK DT-500GC Glass Crusher In Stainless Steel
The DT-500GC is a newly developed glass-crusher from Delitek AS, based upon the same design as the DT-500mkII waste compactor. The glass-crusher is meant for destruction of different types of glass bottles. The outcome from the DT-500GC is small fragments of crushed glass that is collected into "big-bags" inside the container. This makes it very easy to handle this type of recyclable material. The DT-500GC combined with the "big-bag" is an ideal solution in cases where glass bottles is considered as a waste problem. When the "big-bag" is full, the container is ready to be rolled out of from the glass-crusher. Get rid of your glass bottle problems by using a Delitek glass-crusher!
|
|
A unique, compact, high speed, high reduction ratio cone crusher for sample crushing in laboratories and sampling systems.
The Wescone 300 features a unique, internationally patented, simultaneous double crushing action that assures rapid reduction of the feed material and minimises production of oversize discharge to typically less than 15%. Test and production crushing has produced reduction ratios of up to 20:1 with throughputs up to 1kg per second**. The centre of the Wescone crushing action is close to the eccentric mass of the crusher which means lower out of balance forces allowing higher operating speeds. The Wescone can be operated at a speed to generate maximum fines or at a slower speed to produce fewer fines and a higher proportion of particles closer to the crushing gap setting.
|
|
The Labtech Essa 450mm diameter Hammer Mill is designed to reduce approximately 50mm diameter drill core or lump ore to 100% minus 2mm with approximately 80% minus 250 micron.
It is supplied as standard complete with 7.5kW direct drive motor, lead, plug, stand and dust hoods. A blow down air system to reduce cross contamination between samples is also supplied as standard.
All wearing parts are readily replaceable.
Pneumatic or electromagnetic disc braking is available as an optional extra. This provides for safer operation and allows rapid cleaning between samples if required.
|
|
* Jaw Crusher, Model JC1000 :
A medium duty general purpose 130 x 100 mm laboratory jaw crusher The Essa model JC1000 is a well proven single toggle jaw crusher that finds general application in a variety of laboratory environments. It readily accepts soft to medium hard ore, rock and similar particulate up to 85% of its 130 x 100 mm jaw opening.
* Jaw Crusher, Model JC2000 :
A heavy duty, general purpose 200 x 130 mm jaw crusher. The Essa Model JC2000 is a well proven single toggle jaw crusher that finds general application in a variety of laboratory environments. It readily accepts soft to hard ore, rock and similar particulate up to 85% of its 200 x 130 mm jaw opening.&nb.
* Jaw Crusher, Model JC2500 :
High Performance - Fine Product - Reliable Operation. A superior primary jaw crusher engineered for rapid reduction of large lump ore to 2mm in a single step. The Model JC2500 jaw crusher has evolved from Essa Australia's ongoing product improvement programme. It incorporates numerous design enhancements that ensure high throughput, consistently fine product and maximum availability. It has been purpose designed to assist exploration laboratories undertaking two-stage sample reduction protocols. It efficiently processes drill core and lump rock up to 110mm in size producing a very fine ma.
* Jaw Crusher, Model JC3000 :
A heavy duty, general purpose 300 x 200 mm jaw crusher. The Essa Model JC3000 is a well proven single toggle, high reduction jaw crusher that finds general application in a variety of operating environments. It readily accepts soft to very hard ore, rock and similar particulate up to 85% of its jaw opening.
* Jaw Crusher, Model JC5000 :
A heavy duty, general purpose 500 x 300 mm jaw crusher The Essa Model JC5000 is a rugged, single toggle job proven jaw crusher that finds general application in a variety of operating environments. It readily accepts soft to very hard ore, rock and similar particulate up to 85% of its 500 x 300mm jaw opening.
|
|
Plain and tooth rolls for intermediate size reduction.
Labtech Essa rolls crushers are designed for rapid, controlled size reduction of ore, mineral or rock prior to metallurgical testing or further milling or grinding. They are typically applied in laboratory or pilot plant applications after primary production of the infeed material in a jaw crusher or similar. The nipping action of two off same diameter individually powered contra-rotating rolls produces an ideal crushing environment for a wide variety of materials. Product sizing is controlled by an (adjustable) gap setting between the two rolls. One roll is heavy duty spring mounted as protection against uncrushable material attempting to pass between the rolls. Roll crushers operate with a minimum of dust generation and produce a material with a tight size envelope containing a minimum of fines.
|
|
Fluidised Bed Opposed Jet Mill AFG
Dry Processing – Micronising + Air Classifying
Fluidised bed opposed jet mill for manufacturing powders with a steep particle size distribution and sharp top size limitation in the range
< 5 µm to 200 µm.
Grinding nozzles arranged around the periphery of the grinding chamber.
Classifying wheel(s) arranged horizontally in the classifier top section.
Cool and contamination-free grinding.
Cleaning made easy by the hinge-back and removable classifier top section and the inspection deck in the mill housing.
|
|
60,000 lbs. compacting force reduces drums to 4" pancakes
Rugged, full enclosed compaction chamber Automatic push-button controls
Safety interlock prevents operation if door is open
Second compaction head quickly converts drum crusher to in-drum compactor
Location plate keeps drums centered in chamber
Forklift pockets allow for easy removal of heavy compacted drums
Large feed area accepts even 5-gallon pails for in-drum compacting
Options include xp motor, drip pan, remote operator station, and platen spike
|
|
| ... products without technical information |
| |
... see all the products in the category
Grinders
|
|
|