|
|
Clinch studs are inserted through pre-pierced sheets into clinch dies. Initially the hole in the sheet is widened by the calibrating collar. After that, the clinch stud is precentred by means of the calibrating collar. Finally, the sheet material is forced into the annular groove and the Torx locking feature is pressed in. A very high loadcarrying capacity is achieved by means of the patented underhead geometry.
The reduction of production stages and of energy consumption results in considerable cost savings. An additional advantage is the possibility of processing several clinch studs in a single stage.
|
|
ProHold® Tip Screw Holding Technology Bondhus is the developer and exclusive manufacturer of patented ProHold® tip tools - the best screw holding technology available.
- Holds screws tight on the tool every time
- Available for both hex and star tools
- Bondhus is the only manufacturer making screw holding tools in sizes as small as .050" and 1.27mm
- Smooth tool rotation is preserved
- Does not reduce the strength of the tool or cause damage to the screw head
- Non-magnetic
- Never drop a screw again
- Available in a full range of Hex and Star sizes: .050" to 3/8", 1.27mm to 10mm, and T9 to T60
|
|
MICI 80 / 180
motion up to 180 µm
high resonant frequency
parallelogram construction
additional mass up to 20 kg
applications:
quality control
automation
fine adjustment of optical components
mikro-assembly
This element was originally developed for quality control in the optical industry %u2013 it consists of a piezostage in combination with a micrometer drive.
The user can first adjust the position of the actuator and then fine-tune this position with the aid of the piezostage.
The resolution is in the nm and sub-nm range.
Because of the very robust construction of the element, an additional mass of up to 20 kg can be lifted.
|
|
MICROMETER SCREW
• SYLVAC inductive measuring system, patented
• Digital display LCD, height of digits 6 mm
• Data output RS232, combined with external power supply
• Simplex transmission
• Rotating display Ø 44 mm over 270°
• Non-rotating spindle
• Tungsten carbide anvil
• Fine adjustment as accessory
|
|
Extrusion welding is carried out in wide variety of areas and is becoming evermore demanding. Leister offers the right tool for all plastics applications in process equipment manufacture and civil engineering. The specialist obtains everything with us from a single source: Devices from 0.3 to 6.0 kilo per hour. Convince yourself.
• Ideal for tight spaces
• 360° rotatable welding shoe
• Easiest possible handling
|
|
New hand-extruders are equipped with brushless self-blowers lasting more than 40,000 hrs work, self-diagnose system, working-hour counter, double temperature controller with 2 C accuracy.
The extruders are ready to work within 3.5 min and they cool down automatically within only 2 min., ensuring much longer life to the heating elements to further reduce the equipment maintenance.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
Screw-in cylinder, series SWN
Ø 6 - 16 mm, single-acting, spring retracted
Working pressure
min/max : 2 / 8 bar
Ambient temperature min./max: -20°C / +80°C
Medium temperature: -20°C / 80°C
Medium compressed air acc. to ISO 8573-1: 2001
Compressed air class class 5-4-4, class 6-4-3
materials:
cylinder tube: aluminum, anodized
piston rod: stainless steel
Seal : acrylonitrile butadiene caoutchouc
Nut : galvanized steel
|
|
TesT 205 screw testing machines were newly developed based on the
experience of many years and essentially consist out of 4 components:
• 1 force/torque transducer
• 1 machine frame with regulated drive, angle measurement and table
• 1 PC with integrated data acquisition board and motor control
• 1 Software package
The evaluation takes place in real time processing and online during
the test sequences. The force/torque transducer is patented. Its shaping permits the measurement of the 3 quantities: total torque, head friction torque and clamping force without influence of one quantity by one of the others.
Sequences can be programmed by yourselves using the general instructions existing in the software. The available finished software packages according to international standards or standards of the car
manufacturers can be adapted to the individual desires of the user at
any time.
|
|
New "direct drive" screw press with rotative linear motor
The new screw press that Ficep is proposing in addition to the traditional screw presses with disks control, is characterized by technical innovations which place this machine ahead of the market.
|
|
... see all the products in the category
Presses
|
The screw connectors are intended for stranded and solid aluminium and copper cables, carrying low and medium voltages of up to 36 kV. The range covers cross-sectional areas of 6-630 mm² for round cable and 25-300 mm² for sector cable.
Connection to the conductors is achieved by tightening the screws in the through connector or terminal to a predetermined torque. Tightening takes place into a partially threaded nut. The tightening torque is correct when the screw breaks at its notch. It does this thanks to an innovative double-ended shear-off screw, as shown in the illustration
|
|
Bellows
Arnold bellows offer safe protection for both people and machinery. These are the products to soke your problems - in which material, stability and shape can be individually customised.
If the bellows will be subjected to high mechanical stress and strain, the telescopic covers provide safe protection even at high processing speeds. Due to our patented mounting system, the telescopic covers will either be flexibly mounted or connected with the bellows without the use of adhesive materials under consistent counter pressure, if required and can also be coolant-compatible, if this is desired.
|
|
|
Internal anti-backlash leadscrew drives ball slide or crossed roller slide assemblies. Available in one two or three axes. shaft coupling and motor mount included.
|
|
FusionTM II screw. Delivers enhanced mixing while retaining benefits of the original FusionTM screw, namely higher output and lower melt temperature. Applications: injection molding, extrusion and blow molding.
MultiMeltTM injection molding screw. "Universal" screw works with almost any polymer except rigid PVC. Combines productivity benefits of barrier flights for melting with an integrated StrataBlend® II mixer for improved color and additive dispersion and temperature homogeneity.
EasyMeltTM injection molding screw. Combines the simplicity and economy of a conventional three-zone screw with the productivity and quality benefits of optimum material feeding, melting and metering.
StrataMeltTM injection molding screw. Resin-optimized single-stage geometry like the EasyMeltTM but with an integrated StrataBlend® II mixer for improved color and additive dispersion and temperature homogeneity.
FusionTM Screw. New-generation barrier screw boosts productivity, lowers melt temperature and improves color/additive dispersion in injection molding, extrusion and blow molding.
EfficientTM Extrusion Screw. Barrier screw for extrusion proven for more than 30 years in the field.
|
|
The Vrieco-Nauta conical mixer is a convective mixer with a high mixing efficiency that treats your product gently and guarantees the highest level of mixing accuracy without any product distortion.
The Vrieco-Nauta conical mixer was developed more than sixty years ago. Since then, many product innovations have followed. The reliability of the design and performance that is known the world over is exhibited in countless installations in a wide variety of applications.
|
|
|
Roller screw jack provide higher performance compared to ball screw jacks. Ideally suited to applications where a high dynamic load, high accuracy, high speed and a long life are required.
|
|
Pressfit Power Taps with Screw Mount and Angled Slip-on Terminals
10 pin
Pressfit Power Taps with Screw Mount Terminal
6 pin
10 pin
Solder Power Taps with Screw Mount Terminal
6 pin
10 pin
|
|
|
|
