|
|
Applications:
Air Heating, Air Ovens, Load Banks
U.L. Recognized - E56973 C.S.A. Certified - 016386-0-000
Construction:
-Seamless stainless steel sheath
-Post terminals
-Ceramic element support
-Element wire is situated in close proximity to outside surface for maximum heat transfer and minimum internal temperature while preserving good dielectric qualities.
-Magnesium oxide packing
-Aluminum fins offering maximum radiating surface and providing for rapid heat transfer to the surrounding medium. Stainless steel fins are available for corrosive environments.
Aluminum fins are standard. |
|
U.L. Recognized - E48358 C.S.A. Certified - 016386-0-000
Applications:
Battery Warmers, Cabinets, Defrost Applications, Heated Food Tables, Laboratory Equipment, Incubators, Ceiling Panels, and Wall Panels.
Features:
-The Hotwatt Foil Heater is a self-contained one-piece assembly.
-A resistant element is laminated between two layers of aluminum foil.
-The heater is ideally suited for area and surface heating applications.
-Sheath temperatures to 300°F.
-Widths range from 1 1/4" minimum -36".
-Lengths range from 4"-60".
-Heaters are available with a thermostat.
-Many configurations with or without holes and cutouts are available.
-Made in U.S.A.
Wattage:
The maximum wattage is based on 3 watts per square inch of surface.
Voltage:
Voltage is normally 120 or 240 volts. Lower voltages are available.
Construction:
-Aluminum foil
-Insulating sleeve
-Premium grade resistance wire element
-Insulated leads |
|
Strip heaters: Mica Insulated
U.L. Recognized - E56973 C.S.A. Certified - 016386-0-000
Applications
Dies, cylinders, kettles, molds, process machines, platens, tanks, or other applications
where controlled heating is needed.
Features
Strip heaters may be used single or in groups to provide the required amount of heat.
For maximum distribution, it is recommended that the strip heaters be clamped securely
to area to be heated to prevent distortion or unequal expansion.
Made in U.S.A. |
|
SILICON HEATING PANELS - for complicated shapes and sizes
Silicon Heating Panels provide external heating to surfaces of any complex shape and size. Being totally water resistant they can be used both indoors and outdoors. They are used for removing moisture, dehumidification of motors & control devices, for battery heating in high-altitude aircrafts, gas turbines, medical equipment & food equipment. They can also be used in petrochemicals, pharmaceuticals & chemical industries
Construction
Silicon Heating Panels comprises of resistance wire-wound heating elements embedded in thin, lightweight fiber glass cloth - Silicon rubber composite substrates, forming a very flexible and high strength heating panel. For convenience of installation, pressure-sensitive adhesive backing are provided on one side of the heating panel. For minimum heat losses these should be backed by thermal insulation pads. |
|
U.L. Recognized - E56973 C.S.A. Certified - LR-16386
Features:
-The Hotwatt Stainless Steel Strip Heater provides clean, dependable heat with sheath temperatures up to 1200°F and watt densities up to 40 watts per square inch.
-Because of the seamless stainless steel sheath, Hotwatt Ceramic Insulated Strip Heaters are dimensionally stable in milled slots.
Applications:Dies, Molds, Plastic Forming and Sealing, Tank and Kettle Heating. For specific applications, correctly rated elements should be used to prevent overheating and to ensure long life. A guide to correct watt densities for specific applications is shown below.
|
|
-The Hotwatt Tubular Heater has built-in resistance to shock, vibration, corrosion and temperature extremes.
-The heater is swaged, reducing the diameter of the metal sheath and compacting the insulation. This insures rapid heat transfer and holds the coil in position for forming.
-Many formations are available.
-Long, trouble free service.
-Made in U.S.A.
|
|
Silicone rubber is a rugged, flexible elastomer material with excellent temperature properties. It is most suited to larger heaters and industrial applications.
- Rugged construction provides high reliability in a wide range of heating applications.
- Optional custom profiled heat density creates a uniform heatsink temperature which can improve processing yields.
- Factory vulcanization and high temperature capability allows higher wattage levels for faster processing.
- High temperature capability to 235°C (455°F)
- UL component recognition available
- Resistant to many chemicals
- Not suitable for radiation, vacuum, or prolonged exposure to oil
- Most economical in large sizes
|
|
The versatile Watlow cable heater can be formed into a variety of shapes as dictated by its many applications. These small diameter, high performance units are fully annealed and readily bent to your desired configuration.
Applications
Plastic injection molding nozzles
Semiconductor manufacturing and wafer processing
Hot metal forming dies and punches
Sealing and cutting bars
Restaurant and food processing equipment
Cast-in heaters
Laminating and printing presses
Air heating
Heating in a vacuum environment
Textile manufacturing |
|
Applications:
Radiation heaters, vacuum technology, submersible heaters, containers, valves, pumps, forms, process and plate heaters. |
|
Characteristics: A complete range of heating cables, heater strips, woven resistors, drain cables, heat-trace cables, and cables for underfloor heating.
Applications: Refrigeration (reach-in refrigerators, refrigerating compressors, cold rooms, refrigerated units), construction (floors, gutters, roads), industry (petrochemicals, agrifood, aerospace), rail transport (points, trains, metro systems), other (wind farms, aquariums).
Brands: FLEXCORD, FLEXUNIT, FLEXDRAIN, FLEXTAPE, STPGEL, ANTIFREEZE, FLEXFLOOR, FLEXBELT, FLEXMAT, FLEXPLATE, FLEXDRUM, FLEXKIT |
|
The main distinguishing characteristics of heating cables
are their extremely versatile flexibility and the possibility of
built-in supply leads guaranteeing the best insulation
resistance even when operating in immersion or in high
moisture rate environments. |
|
Application Pontencial:
Submersible heaters, containers, valves, pumps, form, process and plate heaters.
This mineral-insulated heating cable with a braiding of high grade stell 14541 is applicable within extreme corrosive and damp surroundings. The HIL heating cable is extremely robust and easy to bend. The stainless stell brainding is waterlight, oiltight and gastight. An utilisation temperature of up to 800°C enables a variety of applications. The cold end of the heating cable can be fed into a terminal box and connected by means of a MX20X1.5 screwed connection. |
|
Applications:
heating or het-loss free transport of: oil, grease, wax, resin, tar, paint, water, carbon dioxide, plastics, sealants, etc...
Emplyable pressurised hoses of PTFE from DN 4 to 50 mm; pressure train depending on nominal width up to 600bar. |
|
HEATING CABLES - HC3/EX-HC3 - for industries and hazardous areas.
Thermo Heating Cable HC3 are the hardy and tough heating cable. When the ambient runs low, strap our workhorse heating cable and keep the fluid flow.
Heating Cable HC3 maintains temperatures in pipelines and storage tanks to keep fluids in flow state. They are the ideal for process heating requirements in Oil & Gas, Petrochemical, Power, Chemicals & Fertilizers, Metallurgical, Cement, Pharma, Food and Edible oil industries.
Construction
Heating Cable HC3 is a series type heating cable with single conductor (multistrand, spiraled) heating element with a primary PTFE (Teflon) insulation, metal braid and an outer PTFE sheath. Each length of heating cable HC3 requires termination kits with cold lead for power connection. |
|
HEATED HOSES - for gas and liquid transfer.
During Gas Analyzer Sampling, Hot Melt Transfer, Petroleum or Chemical Transfers, or Food Processing, it is needed to maintain critical temperatures, to avoid condensation of gas or drop in fluid temperature. Thermo Heated Hoses aptly cater to this need, by ensuring that the fluid in the process tube (part of the heated hose), looses no heat.
These flexible and lightweight tubes can withstand aggressive high pressure fluids and high temperatures involved in transfer of fluids.
Construction
Heated Hose comprises of a process tube bundled with insulated electrical heating element and wrapped with a heat reflecting foil. Temperature sensor is provided at about 300 mm from power connection end. This bundle is insulated and provided with an outer jacket. Ends are sealed suitably and electrical connections for both power and control are brought out. |
|
INTERTEC offers the widest selection of explosion-proof heaters worldwide.
- ATEX/CENELEC approvals for Europe
- CSA/NRTL approvals for America
- GOST approvals for the Russian Federation
Our EX-heaters in combination with EX-controllers satisfy all requirements from freeze protection as well as high demands in the analyse technic.
For further questions please contact: Tel.+49-9445/9532-0
|
|
THERM HI "smart heater" is a system consisting of
an explosion-proof electric heater and a
microprocessor, designed to control the air
temperature in instrument enclosures and protective
cabinets and to limit the surface temperature of the
heater.
The "option E" is equipped with an intrinsically safe
sensor, thus allowing measurement and accurate
regulation of the temperature of the instruments and
equipment (e.g. of manifolds).
... THERM HI heaters are designed to solve
sophisticated and complex heating problems in
hazardous areas, and in particular for high
temperature maintenance of analyzing equipment. |
|
Applications:
Heating of pipes, containers, pumps, filter, flanges, connections of the heating hose. |
|
Product: flexible electric resistances with technology PTF (Polymer Thick Film)
Applications: destined to varied fields, in particular where one demands a homogenous heat source with flexibility characteristics and thinnest thickness.
Some examples of employment: elements for sbrinamento, anticondense, evaporation for apparatuses refrigerators, elements heating for scaldavivande, to yogurtiere, scaldabiberon and other household-electric little ones, heating plans.
Characteristics: personalized planning, with possibility of realization in varied forms and dimensions and several types of isolation electrical worker.
Possibility to realize resistances with effect PTC (resistances autoregolanti) for applications that had to demand it.
Other characteristics:
The thickness is a lot reduced, typically less than 0.2 milimeter
The posterior part can be rendered adhesive.
It is possible to have on the same resistance a differentiated generation of heat.
The resistances are realizable in all the supply voltages, comprised the lowland tension.
The temperature comes caught up in times breviums and with low consumption.
|
|
Applications:
These can be fabricated for use in warming tables, cabinets heaters, cooling tables, heating plates for form carriers or even radiating heaters for household use. |
|
Band heaters are designed for use in different applications:
- Ceramic band heaters: with an heating spiral manufactured from NiCr and steatite insulated, these heating elements are sheathed by an Alusi or stainless steel jacket. Increased insulation is achieved through a layer of mineral fibre. Max. operating temperature: 600°c and max. surface load 8W/cm². Especially designed for plastics injection moulding and extrusion where high temperature is required. |
|
Led by the high performance MI (mineral insulated) Band heater, the patented, flexible THINBAND® heater and the standard mica band heater for specialized constructions, Watlow's band and nozzle heaters are ideal for every type of plastics processing equipment.
Applications
Extruders
Blown film dies
Injection molding machines
Other cylinder heating applications |
|
hotrod® cartridge heaters (type HHP and LHT) are core products of hotset´s tradition. Excellent knowledge, high-quality materials as well as the outstanding manufacturing guarantee long life and excellent product features.
By intensive cooperation – also with special applications – hotset gives again and again innovative impulses to its cartridge heaters with new technical features (e .g. humidity-resistant connection area).
By optimal production conditions of Hotset Malta Ltd. an unique price-performance ratio can be achieved for larger quantities. Hotset cartridge heaters offer high functionality and high production safety – driving quality!
|
|
| Specific for the cartridge heater is the single-sided connection, granting high perfomance in terms of temperature and power. All application sectors are covered by this heating elements, cartridge heaters. |
|
Vulstar® cartridges are used to heat metal like moulds, dies, plates and bolts or liquid.
Supply voltage up to 450 V 1P or 3P.
Load up to 40 W/cm2.
Length from 25 mm to 2500 mm depending on diameter.
Diameter from 6,35 mm (1/4") up to 31,8 mm (2" 1/4).
Different types of connection to fit with the ambient temperature.
This cartridges can be provided with a thermocouple . |
|
The Watlow FIREROD® heater enters its 50th year of industry leading expertise as the premier choice in swaged cartridge heating. With premium materials and tight manufacturing controls, the FIREROD heater continues to provide superior heat transfer, uniform temperatures and resistance to oxidation and corrosion even at high temperatures.
FIREROD offers many delivery programs to meet your needs: same day shipment, Ship-to-Stock or Just-in-Time. And our experience in customized engineering is reflected in over 250,000 FIREROD cartridge heater designs. Stock or made-to-order, the Watlow FIREROD delivers heat in a hurry.
Applications
Molds
Dies
Platens
Hot plates
Sealings
Fluid heating
Life sciences
Aerospace
Semiconductor
Foodservice equipment |
|
hotset presents a wide product spectrum of hotspring® coil heaters:
- Starting with WRP / Micro up to WRP / Maxi with different lenghts and diameters.
- Brass-coil heaters or coil heaters with clamping mechanism as heating elements for different applications.
- Heating systems such as the hotcast® sealed heater (GMH) or the hotcone® heated nozzle (BMD).
- Special products such as hotslot® and hotslight®.
- As well as a wide spectrum of applications.
hotset was already in 1980 one idea ahead as they presented the first round coil heater (type WRP Ø 3.3). Since then further innovations have been made: WRP / Mini, flat and square coil heater (WRP / F resp. WRP / Q), WRP / Maxi as well as WRP / Micro.
This innovation as well as the humidity-resistant coil heaters according to I.P. 65 (WRP Ø 3.3 - WRP / F 2.2 x 4.2 – WRP / Q 3.0 x 3.0) emphasize the consequente alignment to new challenges.
|
|
Heaters for the thermo-regulation of enclosures, for application on DIN rail, and available in three version:
- with bipolar (15-30W) or three-pole (45-150W) power cable
- with three-pole terminal block (45-150W)
- ventilated (250-400W) |
|
|
|
