|
|
|
|
|
|
Farming hot air generator completely autonomous with heating gas oil, natural gas or liquefied petroleum gases (butane gas, propane gas) operation.
These equipments function is that one of heating the environmental air by means of the thermal energy produced by the equipment.
The produced heat is driven to the premises that must be conditioned by means of a centrifugal fan.
The combustion products are extracted through a chimney in order to ensure that the driven hot air is exempt of smokes and bad smells.
The main features are the following ones:
-Heating gas oil, natural gas or liquefied petroleum gases operation.
-Closet made with galvanised sheet.
-Heat exchanger dimensioned in order to obtain performances superior to 90%, made with AISI-430 stainless steel.
-Combustion chamber made with AISI-304 stainless steel.
-Control panel made in a watertight box for avoiding the high humidity degree in greenhouses.
-Reinforced environmental thermostat with 5m hose and fast connector included in the equipment.
-Base equipment prepared with air impulsion grid of simple deflection.
-It can have circular hoppers or any other kind of impulsion pipes coupled on it.
|
|
SYSTEMA introduces the new series of EOLO, suspended warm air heaters able to solve all heating problems, both for total and modular space heating. Compared with traditional heating systems needing a separate cabinet, the new EOLO heaters offer an innovative solution for heating while keeping running costs at a minimum.
This is possible thanks to the fact that EOLOs are completely self-sufficient working units, and that you don?t need to heat up a heat transferring fluid such as water for heating the space. In this way you don't have any needless heat losses.
|
|
Full range of heating cabinets gas or oil fired.
Available in vertical or horizontal versions, inside or outside and able of ducted appications.
Air flow from 6000 to 60000 m3/h and power from 70 to 1120 KW.
High temperature resistant steel exchanger or stainless steel.
For various cases, the body can be double skin.
Filtration optional.
Applications : Industrial buildings heating and/or ventilation with sveral kind of applications for high level confort for users.
This equipment is in accordance with European directive related to gas fired equipment 90/396/CEE under n° 49AQ1369 and 1370 and electro-magnetic compatibility CEM 89/336/CEE and low voltage 73/23/CEE.
|
|
DESCRIPTION:
Gas domestic hot air generator with leakproof operation and smoke outlet through an extractor.
Its operation is completely autonomous and its function is that one of heating the environment air of the premises that must be conditioned.
The basic equipment has the following elements:
- Leakproof combustion with forced draft.
- Combustion oven designed for obtaining a performance of about 90%.
- Three-speed fan (except for the GAS-40 model, which is one-speed).
- Air admission filters.
- Environment thermostat.
- Air impulsion grid on the upper part (GAS-08-12-15).
FUEL:
Natural gas / LPG
APPLICATIONS:
Any kind of premises with a volume between 190 m3 and 980 m3.
|
|
Hot gas generators fabricated by Unitherm Cemcon are designed for direct air heating performed by a firing system. Air to be heated is either supplied by a dilution air fan or is delivered from process with high or low temperatures or combinations of both.
Unitherm Cemcon provides:
* Hot gas generator engineering for supply or local manufacturing
* brick lining material
* Burner (mono block or special designs) incl. operation valve train and fuel supply system
* Diluton air fan
* HGG field instruments for performance and safety control
* HGG control cubicle
|
|
| ... products without technical information |
| |
|
|
|
|
AGC – the true meaning of multi mains
The updated AGC Automatic Gen-set Controller handles an astonishing 56 breakers and is immune to a failing master controller due to the integrated multi-master principle. Combined with an exhaustive list of other new features, it will simply enable you to do things you would have never thought possible.
Up to 16 mains incoming, 16 mains breakers, 16 tie breakers, 8 bus tie breakers, 16 generators and 16 generator breakers; if this fits the description of your application, you might want to continue reading.
All 56 breakers can be synchronised and communication between the controllers will be fully redundant – all by choice and without extra cost. Moreover, the AGC offers selectable mains priority and parallel operation.
Applications
The AGC supports a vast number of different applications for single gen-set, multiple gen-set and multiple mains. For all of these applications, the AGC supports a number of different plant modes:
> Automatic mains failure/ATS
> Island operation
> Fixed power/base load
> Peak shaving
> Load take over
> Mains power export
|
|
G59 protection relay package
The mains decoupling relay - type G59 package – forms part of a complete DEIF series of relays for the protection and control of generators. This package is applied for the protection of synchronous generators, running in parallel with the mains.
Features include:
- Combined vector shift and ROCOF (df/dt)
- Protection of over-/underfrequency
- 3-phase protection of over-/undervoltage
- Digital data processing
- Fast decoupling of the generator
- Ensures no asynchronous reconnection
|
|
The Loss of Mains Relay type LMR-111D is for protection of the generator against damage resulting from a non-synchronised reconnection to the grid after a temporary mains failure.
Features include
> Detection of vector shift
> Mains disconnection on mains failure
> Ensures no asynchronous reconnection
> LED indication of fault condition
> LED indication for activated relay
> 35 mm DIN rail or base-mounting
The Loss of Mains Relay type LMR-111D forms part of a complete DEIF series of relays for protection and control generators
|
|
|
|
|
|
he Summarize Measurement and Protection Unit (SMPR-1) has been designed to measure the line and ground RMS currents and supply RMS voltages under normal conditions or under disturbances. The voltage and current signals are sensed throughout potential transformers (PT) and current transformers (CT) from each line. This information is internally processed by the microprocessor, to take the current protection actions defined under ANSI, IAC or IEC standard. Additionally the operational conditions of the breaker or disconnector are also signalized. The different functions provided by the SMPR-1 may be classified into the following groups:
Applications:
* Primary and backup protection for power plants, utility and industrial distribution systems.
* Protection of transformers, overhead lines, cables and generators.
* Permits the opening of the switch/disconnector within the limits of its capacity, those identifying the excess (e.g. straight short-circuits), leaving the circuit interruption to the back-up fuses.
|
|
G60 Generator Protection System
The G60 Generator Management Relay, part of the UR family of protective relays, is a microprocessor-based relay intended for the protection of AC generators. It may be used on any size of generator driven by steam, gas and hydraulic turbine.
Protection functions include stator differential, 3rd harmonic stator ground differential and 3rd harmonic neutral undervoltage for 100% stator ground differential protection, sensitive directional power for low forward power and reverse power protection, loss of excitation, inadvertent energization, overexcitation, current unbalance, out-of-step, and a whole suite of under- and overvoltage, and overcurrent functions.
|
|
| ... products without technical information |
| |
Teledyne Energy System has been at the forefront of thermoelectric power systems for the past 40 years, starting with the SNAP3 space generator in 1961. During that time, Teledyne has produced hundreds of generators ranging in size from milliwatts to multi-hundred watts for both space and terrestrial applications.
Beginning in 2001, Teledyne began developing PEM fuel cell systems for the aerospace market. Applications include high efficiency PEM powerplants for Reusable Launch Vehicles for NASA, regenerative systems for high altitude unmanned aircraft/airships, and advanced designs for unique missions.
Teledyne specializes in custom designs for a wide range of customers and has the complete in-house capability for both commercial and classified applications involving thermoelectrics or PEM fuel cell power systems.
|
|
|
In the 2MW electrical power range, the OPRA package produces the highest thermal power which makes it ideal for co and tri-generation applications.
|
|
|
|
|
|
Trigeneration is the conversion of a fuel into three useful energy products: electricity, hot water or steam, and chilled water. A trigeneration system is a cogeneration system extended with an absorption chiller that uses some of the heat to produce chilled water for air-conditioning of buildings and building complexes.
With a Wärtsilä trigeneration power plant you will reach the same output with notably less fuel input compared to separate power and heat generation.
Wärtsilä power plants have ready-made solutions for trigeneration which can easily be adapted to different market and customer requirements and delivered within tight time schedules.
Benefits
The trigeneration system makes utilization of the engine CHP plant highly efficient throughout the annual seasons and through changes in the local climate. The plant can flexibly run at high total efficiencies, producing heat and cooling for airport terminals, office and building complexes, housing areas, etc., and can interchange smoothly between supplying heating and/or cooling. At the same time it supplies the needed electrical power.
|
|
|
|
|
|
CAMPOFRÍO ALIMENTACIÓN S.A. is a leading international company within the food sector. It produces meat products which, for the production process, requires significant amounts of heat, in the form of steam and hot water, industrial cooling and electrical energy.
In 1996, with the purpose of reducing energy costs on the production processes and equipping the company with flexible installations in order to meet both present and future energy needs in a secure and efficient manner, GUASCOR ENERGIA went into a joint venture with Campofrío in order to construct and operate a Trigeneration plant - producing heat, cold and electrical energy - .
The Trigeneration plant operates 24 hours per day, seven days per week with a total of 8,700 hours of operation annually.
The installation incorporates four turbo-charged gas engines, each one rated at 3 MW, with a total installed power of 12 MW.
To cover the cold demand on the production process, the trigeneration plant is fitted with an ammonia - water absorption machine, which runs off saturated steam obtained from the heat recovered from the engines' exhaust gases.
|
|
| ... products without technical information |
| |
The leading-edge ultrasonic generators DIGITAL SE-09 series, are designed and assembled to be employed in the ultrasonic welding of thermoplastic
material pieces. These generators are totally digital and incorporate all the most important and typical regulation features of modern generators.
The innovative programming system, is controlled by means of a rotating selector switch; all the settings can be carried out using a single knob. This generator stands out for its easy to use; all the range of functions and the absolute reliability make this generator only one of its kind.
All the generators DIGITAL SE-09 series, are equipped by a backlight display and
can be supplied either in an elegant metal frame or as a single module.
The generators small dimensions and modularity, allow to have a double set-up inside the metal frame.
|
|
The ultrasonic welding generators: DG machine, DG system & DG rack have been developed for the ultrasonic welding machines.
Reliable, these generators are all digital and allow a high quality monitoring control.
Technical data:
Power from 500 to 4 000 watts
Frequency 20, 30 & 40 kHz
Voltage 230 V 50 Hz
Dimensions 135x540x140mm
Ethernet connexion
Automatic tuning frequency during the welding process
Fitted out the last generation of microprocessor: RAM7 32bits
|
|
The ultrasonic welding generator "ACU" is suited for the operation and control of ultrasonic welding machines of the "Dynamic Series". In addition to the three different welding modes (time-, travel- and energymode) and the optimized force profiling the ACU features an electronic amplitude control. The optionally available software "ACUcapture" enables the download of welding parameters and graphics directly from the generator to the user's computer. "ACUremote" allows to modify the parameters whereby a remote maintenance is possible.
- Real time operation
- Graphic display
- Interfaces for data analysis and parameterization
- welding data as well as for remote maintenance
- Simple adaptation to special purpose machines
|
|
SINAPTEC created a product range common to welding and the cut.
The assembly with ultrasounds applies to any type of materials thermofusible, plastic and textile technical in the textile and packing, plasturgie, motor-car industries.
this process makes it possible to weld closely or to cross, deburr, punch...
The equipment of welding or cut SINAPTEC is composed of a generator of energy and an applicator of energy (an electromechanical converter which transmits the ultrasonic vibrations to the tool)
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
