|
|
- Performance up to 95%.
- Big airflow fan to reach the temperature of comfort in very short time.
- Pellets burner of high thermal efficiency with security systems.
- Electronic control that actuates all functions to a properly functioning of the equipment.
- Pellets feeder with motor-reducer for the provision of required fuel in each process.
- Pellets container of 220 kg capacity.
- The distribution of hot air can be made through rotating plenums, perimeteral grills or through air ducts.
|
|
DESCRIPTION:
Fully automatic domestic stoves and respectful of the environment as they use as fuel pellets (pressed wood waste).
With controlled electronic on/off and automatic, equipped with ambient thermostat, five heating powers, programmer with two daily on and off, etc.
|
|
GADD
Fully assembled with double heating elements that provide twice the heat intensity of the GAD but with less even heating. Suitable for applications requiring contact-free heating.
|
|
DESCRIPTION:
Hot air heater that operates with solid waste, as for example dry wood, coal, husks, cardboard, etc.
Since it is an equipment which uses natural elements as a fuel, it can be classified as an equipment of biomass.
The range is composed of a 69kW model.
For technical specifications and a complete description, go to "READ MORE" and download "DOWNLOAD TECHNICAL INFORMATION ".
FUEL:
Wood, coal, husks, etc.
APPLICATIONS:
Whatever premises that need a heating system in which the fuel to be used is wood or a similar material.
|
|
DESCRIPTION:
Hot air heaters that operate with solid waste, as for example dry wood, coal, shell, cardboard, etc.
There are two series; EP series and ALLMAT series.
EP SERIES
Industrial hot air heater of 50kW and 100kW.
Its features are the following ones:
- Manufactured with steel sheet.
- Helicoidal fan (EP-050) and centrifugal fan (EP-100) with security protections.
- Big access door for introducing the solid waste.
- Smelting grid for the solid waste layout.
- Refractory bricks all over the equipment for containing the heat driven away by the equipment.
- Thermostat with automatic start-up of the fan in order to avoid impulsion of cold air.
ALLMAT SERIES
- Domestic heater for small premises.
- Helicoidal fan located on the inferior part of the equipment.
- Completely insulated equipment for avoiding the heat radiation.
- Big load access door located on the superior part of the equipment.
- Air regulator for a proper combustion.
|
|
DESCRIPTION:
Stove of industrial firewood with ventilator with operation to firewood, shavings, charcoal, etc.
Ideal for the heating of the industrial premises with a maximum volume of 1.075m3 to 2.150m3
FUEL:
LEÑA-BRIQUETAS-CARBÓN
|
|
|
Convection Heaters distribute the warm air by relying on the difference in density of the heated air rising above the cool air and creating a convection current. The forced air heater forces air over very long distances and is usually the choice for heating larger areas. Similar to the sun’s heat, infrared heating heats people and objects rather than air or space. Radiant heat is less affected by drafts and large air movements. When using overhead infrared to heat an entire building, direct radiated heat from the heater passes through the air to heat floors, walls, machinery and people. These heated objects then transfer heat to the air by natural convection and secondary radiant heat. Radiant heat generates no noise, fumes or flames.
|
|
A RANGE OF CERAMIC GAS HEATERS ADAPTED TO ALL HEATING NEEDS IN INDUSTRIAL BUILDINGS (height of 4 meters and more).
Use: Industrial buildings, Churches, Sports halls, Car service, Terraces, ...
- a large range of heaters from 2,5 to 27 kW and more.
- a choice of 10 powers for a comfort in all type of buildings whatever the
hanging height of the heaters
- a double-speed option for a better comfort, particularly in well insulated
buildings
|
|
OHA radiant strips are especially fitted for infrared heating of industrial, commercial and sports' buildings up to any type of height. They are on the contrary especially fitted for very high buildings which require large radiant surface with lower surface temperatures.
OHA system does not move the dust in the air, it does not take any space on the floor and its maintenance is extremely reduced. The characteristic of the gas combustion head in premix and afterburning at low NOx emission and high efficiency. The radiant pipe circuit diameter 200/300mm assure a high thermal emission. A special insulation above the radiant strips raises further the radiant yield on the floor.
|
|
Hanging irradiation heating unit suitable for heating big environments.
Including a heat generator with power from 35 to 300 kW and a radiating circuit with average surface temperature of 200-250°C.
The circuit layout is optimized according to the environment to be heated .
It is the best solution for huge environments where a good level of thermal comfort is required.
|
|
Terminal air heater
"Drawer-type" heaters, which are designed to be installed directly in an opening made in the duct, are built around stored elements. They are bent upon request and can be delivered in small series in a week.
For ducts diameter from 100 to 630 mm and rated from 500 W to 36 kW, the terminal heaters for circular ducts are assembled using elements kept in stock. They may be delivered in small series within 48 hours.
A series of self-controlled circular terminal heaters was developed to satisfy the desire of users for precise temperature control in each room. They can be controlled by electronic thermostats or remote industrial controllers. Many safety accessories are optionally available.
|
|
The range of helicoid aerotherm consists in 7 different models used either in heating or cooling mode.
These equipment are intended to large volume buildings, store house, garage, workshop...
Aircalo aerotherm enables rapid heating or cooling volumes at the same time, mixing the air sufficiently to prevent its stratification (it is possible to complete this mixing by using zephir air recyclers).
Depending upon the characteristics of the building to be equipped, the Aircalo aerotherm may be hung (vertical blowing) or wall mounted (horizontal blowing).
CAUTION :
In cooling operation, the vertical mounting (horizontal blowing) should only be used. In this case, a condensate vessel is supplied.
These Aircalo aerotherm are designed to satisfy quality criteria and standards in force.
|
|
* Fan motor assembly with ROTOREX technology and streamlined impeller providing the best compromise between air handling efficiency and acoustic comfort.
* Double deflector diffuser with JET+ technology as standard. A CIAT innovation based on Bernoulli's principle on fluid dynamics and on the NACA0012 type aeroplane wing profile. Comfort, silence and energy saving are not optional at CIAT...
* Highly efficient heat exchanger with tapered baffles. With seventy years' experience in the field of coils, CIAT provides the best combination of tube geometry and fin design on the market.
* Antibacterial condensate drain pan with integrated quick connection fitting for cooling or reversible applications.
* Wide range of accessories for all site requirements (mounting, filtration, fresh air, mixing etc.)
* Extensive range of regulation units for all uses (on/off, proportional, electric battery etc.)
|
|
Effective air flow heating, variable designs:
The best way to heat airflow, as seen in automatic devices or tumble dryers. We produce adapted heating elements for your fans or, when required, with fan.
Open wire heating elements are the best solution for air heating when used in fans. Because of our longlasting experience in this field, we can offer you a series construction in most cases. To use our open wire heating elements in air, the installation of a cut-out is necessary (heat accumulation). The connection is done by a plug at the element (Faston 4,8 or 6,3) or by a cord set.
|
|
|
|
|
|
MODULE FOR INCREASING TEMPERATURE
MM-050-TEC / MM-090-TEC / MM-160-TEC
DESCRIPTION:
Heating module designed for increasing the temperature of the air canalised inside of it (thermal difference of 17ºC to 60ºC).
Its big versatility turns it into an equipment with great application in the premises heating area, as well as in that one of materials drying processes as for example: furniture, metal pieces, vegetables, etc.
Its main features are:
-Operation with heating gas oil, natural gas or liquefied petroleum gases.
-Combustion oven made for achieving a performance of 90%.
-Tubular structure painted with black priming.
-External panel thermally and acoustically insulated.
-It has three operating thermostats (fan start-up, burner stoppage and security thermostat).
-Fastening hooks for an easy transport.
The base equipment does not incorporate fan nor electric panel, but it can be supplied if you ask it so.
FUEL:
Heating gas oil / natural gas / LPG
APPLICATIONS:
Premises heating, products drying, etc.
|
|
- Robust and compact design
- Can be used for fixed mounting on the wall
- Low noise level and high air flow
Proff is a range of compact, portable fan heaters designed for
craftsmen and others who need both temporary and permanent
heating for buildings sites, warehouses, workshops etc. It is
particularly well suited for drying applications. The heaters
have a handle and can easily be mounted onto the wall.
Proff fan heaters must not be used in the proximity of
swimming pools or other places where there is open water.
The units are made of galvanised steel with heating elements
of stainless steel. Powder coated in light grey with a black
stand and grille. Proff 2 kW and 3 kW are supplied with a
2 m supply lead and a DIN grounded plug. The Proff
5 kW and 9 kW are also supplied with 2 m lead but with a
CEE round-pin plug for 3 phase power supply. The Proff
15 kW, 20 kW and 30 kW are supplied with a 1.8 m cable
without plug.
The thermostat can be set between 5°C and 40°C.
|
|
Applications
Type T3C Explosion Proof Unit Heaters are suitable for Hazardous Location Classes I and II, Groups C, D, F, and G. Ignition Temperature Code Rating is T3C, (320ºF), (160ºC).
Standard Features
*Industry's lowest ignition temperature code rating compliant.
*Epoxy coated corrosion resistant cabinet with adjustable louvers.
*Redundant overtemperature protection with dual automatic reset thermal cutouts for safety.
*Sealed heat exchanger with nontoxic Propylene Glycol heat transfer fluid and low pressure 70 PSIG relief valve.
* Cast aluminum electrical enclosure with 24V control circuit.
Options
Contact Gaumer for: Group E (Metal Dust) Construction, Dirty Duty Corrosion Resistance, Arctic Duty Motor (-40ºF/-40ºC), Non-standard motors (ie. 50Hz), Adjustable Thermostat, 120 Volt Control Circuit, Auto/Fan Selector Switch, Manual Reset Thermal Cutout with Magnetic Contactor, Pilot lights.
|
|
SAVANA is a new heating unit. It is offered in four various designs, which enable a wide spectrum of use. The design with a silver front cover with
V-lamellas or Jets is most suitable for supermarkets, stores and sports complexes. The industrial design without a front cover is recommended for production halls and other industrial premises.
SPECIFICATION:
- 4 types of design
- Air output up to 6900 m3/h
- High heater power up to 92 kW
- "V-TECHNOLOGY” and “JET System” for higher output and comfort
- Adjustable bracket for horizontal and vertical setting
- Easier installation for connecting water
|
|
Their flexibility and fast heating feature make it necessary to use the Armagnac in premises such as :
- Sales and/or storage areas
- Sports hall
- Agriculture and breeding premises
- Industrial and commercial buildings.
Over a pleasant presentation, electric aerothem Armagnac are fitted with all components and accessories allowing a quick installation, a safe and quiet operation.
- Armoured resistance
- Slow speed helicoid fan
- Power contactor
- Safety and control thermostats
- Fan timer
- On/off switch with light signal
- White RAL 9003 painted sheet steel frame, RAL 9010 lacquered deflectors protected with a removable plastic film.
Produced in 2 sizes, for power from 6 to 24 kW.
For powers from 15 kW to 24 kW only, the equipment is fitted with contactors allowing a two step operation if necessary.
|
|
|
|
|
|
Heater fans PHE and PHD
Robust, powerful and durable
For heating and ventilation of
Workplaces
Day rooms
Showrooms
Portacabins
Construction sites
or for drying of damp or moist rooms
Robust housing made of galvanised sheet-steel, coated, corrosion-resistant.
Carrying handle as tubular stand with sufficient floor clearance.
Heating elements made of stainless steel, non-glowing.
Thermal overload protection as standard feature. Switches motor off under thermal overload and comes on automatically again after cooling down.
With wall bracket
For portable or stationary operation.
High air circulation. Rapid heating.
5 power classes: from 3 to 20 kW.
Dual-walled housing offers safety.
Robust motor with ball bearings, maintenance-free
Fan and heater can be switched in 3 or 4 steps.
PHD 9/ 15/ 20 with timer: Switch-on time can be preselected up to 24 hours.
Heating thermostat with temperature range which can be set (infinitely variable) to between 0 °C - 40 °C. Fan continues to operate once the temperature has been reached.
|
|
Rectangular fin elements
Consisting of a "U" shaped element on which are crimped the rectangular fins (25 x 50 or 40 x 80) made of protected steel or stainless steel and usually equipped with threaded glands.
|
|
These equipment may be connected either with vertical or horizontal vent or through a chimney.
These aerotherms do meet the main requirements of the CE standards requirement related to gas-fired aerotherm.
CAUTION :
These equipment can only be used in sufficiently aerated premises, except where a tight connection is provided.
The proper operation of the aerotherm depends on a correct installation and start-up.
Aerotherm should not be installed in :
- Hazardous areas
- Premises containing vapours of chlorinated combination
- Areas with high contents of inflammable dusts
- Highly humid rooms.
|
|
BABCOCK WANSON offers a complete range of solutions suitable for the heating of large spaces and smaller buildings :
- air unit heaters gas fired or for use with secondary heat transfer fluids ;
- warm air cabinet heaters gas-fired and light oil fired ;
- air handling units, make-up air replacement heaters and modular units with exchangers, mixing chambers and filter sections ;
- radiant tubes, door heaters, destratification fan units.
BABCOCK WANSON manufactures equipment to deal with a variety of drying applications :
- heaters with direct combustion (up to 12000 kW and 1200°C) ;
- heaters with indirect combustion (up to 3000 kW and 300°C).
|
|
Adding a fan to a heater creates artificial air movement. This air movement allows for a more compact heater than the convection heater since rapidly moving air removes the heat from the heater surface more quickly. The forced air heater forces air over very long distances and is usually the choice for heating larger areas.
Applications
- Shipping and Receiving Areas
- Pump Houses
- Power Generating Stations
- Aircraft Hangers
- Factories
- Warehouses
- Garages
|
|
Consisting of carrier tube in nickel-plated or stainless steel. With spot-melded metal frame and carriers made from mica. Different messures, voltages and outputs are possible.
Applications: Mechanical engineering, plant construction, chemical industry, plastics technology, e.g.
|
|
ULTRAMIC™ 600 Advanced Ceramic Heater
When you need a lot of power in a small package, the ULTRAMIC™ 600 puts the performance of advanced ceramics to work for you. Constructed of aluminum nitride (AlN), the ULTRAMIC 600 can operate up to 600°C (1112°F) and deliver ultra-fast ramping of up to 150°C (270°F) per second for rapid thermal cycling applications.
The robust mechanical structure of the high density AlN enable these heaters to exhibit exceptional mechanical stability throughout the temperature range. This makes the product especially suitable in applications where consistent part-to-part thermal contact during heating cycles is critical. Additionally, these heaters are applicable when requiring a clean, non-contaminating heat source as they are particle free, impervious to moisture and resistant to acidic attack.
Applications:
Semiconductor wire and die bonding
Analytical instrumentation
Medical devices
Packaging
Aerospace
|
|
Fan heaters of simple and robust design for heating recirculated air in areas such as workshops, factory shopfloors, warehouses, refectories, sports halls, garages, shops, greenhouse ...
Vulcanic manufactures a very large range of fan heaters, such as portable fan heaters, fan heaters with castors, and high power fan heaters for wall mounting.
|
|
Mechanically-bonded continuous fin assures excellent heat transfer and helps prevent fin vibration at high air velocities.
Several standard formations and mounting bushings available.
Standard fin is high temperature painted steel with steel sheath.
Optional stainless steel fin with stainless steel or incoloy sheath for corrosion resistance.
120v, 208v, 240v, 480v available.
Maximum Sheath Temperature
750°F (400°C) - Steel
900°F (480°C) - ST.ST./INCOLY
Made in U.S.A.
|
|
The air heater units Gejze are designed for heating nad ventilating the industrial halls assembly rooms, workshops, shopping malls row of shops and similar huge objects.
Gejzer works based on:
- recirculated air (Gejzer I, Gejzer II),
- mixture of fresh and recirculated air (Gejzer MIX).
The heating medium is water delivered to Cu/Al heater from heat source.
There is a possibility of co-operation of several some devices for large building complexes. in the case of large rooms.
There are two models available in market:
- Gejzer I with max. heating power of 26 kW in max. heating power,
- Gejzer II with max. heating power of 52 kW in max. heating power.
|
|
|
|
|
|
Proheat Air is the new standard for heavy-duty truck air heaters, quietly delivering constant and reliable heat in cold weather environments. Available in 2 and 4 kW models, its high-efficiency design reduces overall vehicle emissions and engine wear by eliminating the need to idle the engine to heat the sleeper cab. Proheat Air saves fuel costs for fleets and operators while helping drivers comply with local idling restrictions. A digital remote panel provides comprehensive and precise control of Proheat Air from anywhere inside the truck cab.
Air Heater Features
- 2kW (A2) and 4kW (A4) models available
- Built-in temperature sensor for safety and control
- Ultra-quiet operation
- Optional diagnostic software kit available
- Two year warranty
Digital Control Panel (DCP) Features
- Backlit LCD display
- Easy set-up and control
- At-a-glance display of heater status
- Temperature, time, and power
- Stores multiple timer events
- Surface-mount design
Optional Components
- Proheat Monitor (Diagnostic Software Kit)
- Temperature sensor
- Heater mounting plate
|
|
|
|
