|
|
INTERTEC offers the widest selection of explosion-proof heaters worldwide.
- ATEX/CENELEC approvals for Europe
- CSA/NRTL approvals for America
- GOST approvals for the Russian Federation
Our EX-heaters in combination with EX-controllers satisfy all requirements from freeze protection as well as high demands in the analyse technic.
For further questions please contact: Tel.+49-9445/9532-0
|
|
THERM HI "smart heater" is a system consisting of
an explosion-proof electric heater and a
microprocessor, designed to control the air
temperature in instrument enclosures and protective
cabinets and to limit the surface temperature of the
heater.
The "option E" is equipped with an intrinsically safe
sensor, thus allowing measurement and accurate
regulation of the temperature of the instruments and
equipment (e.g. of manifolds).
... THERM HI heaters are designed to solve
sophisticated and complex heating problems in
hazardous areas, and in particular for high
temperature maintenance of analyzing equipment.
|
|
-Pressure clamp connectors
-Dynamic heating up
-Wide voltage range
-Temperature limiting
-Energy saving
-Clip fixing
-Quick installation
These heaters are used in enclosures where damage from condensation must be prevented, or where the temperature may not fall below a minimum value.
The aluminium profile heater body design has a chimney effect and distributes the heat evenly.
The pressure clamp connectors save time and simplify installation.
|
|
PTC Schaltschrankheizung
Types: P-ssm-Al, P10, P25, P65, P80
Tensions: 12V - 48V, 110V - 265V (wide rank)
Achievements: 10W - 300W
Safety class system II (protective grounding) - enclosure IP 54 (DK = IP 20)
Temperature behavior:
- self-regulating in dependence of the ambient temperature
- dynamic heating
Z.T. Exhaust for better air distribution mountable
Partly 2 connection types
Connecting cable (AL) with silicone cable 2X0,75 mm
Execution clamp (DK) 0.08 - 2.5 mm
Installation position perpendicularly
3 mounting options (alternatively)
Bolt mounting
DIN slides attachment
Attachment by means of thread groove
|
|
Low surface temperature
Quick mounting due to clip fixing
Double insulated (plastic)
Wide voltage range
Small size
Compact heater for the use in enclosures with electrical/electronical components. The design of the heater supports the natural convection which results in a high air-current of warm air.
The surface temperatures on the accessible side surfaces of the housing are kept down as a result of the heater design.
Our complete range of thermostats and hygrostats can directly be connected to the heater CS 060.
This heater is also available in a version with plug-in thermostat requiring no additional wiring (CSF 060).
Both versions are designed for permanent operation.
|
|
Heaters for the thermo-regulation of enclosures, for application on DIN rail, and available in three version:
- with bipolar (15-30W) or three-pole (45-150W) power cable
- with three-pole terminal block (45-150W)
- ventilated (250-400W)
|
|
|
Condensation poses a particular risk for control electronics, especially with outdoor siting, but also indoors. Various different output categories ensure that the correct thermal output is always available. In this way, the total required thermal output can be distributed with complete accuracy within an enclosure.
|
|
Units for DIN or screw mounting.
TH heaters, installed separately from cooling unit, must be connected to a TMC thermostat. When used to prevent cabinet condensate they should be electrically connected also when cabinet is off.In this cabinet its better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
Technical details
- Protection class I (ground wire) - protection type IP 54 (DK = IP 20)
- Temperature setting:
ON 25 C - OFF 55 C (operating temperature of heating
system itself)*
Tropical version possible: ON 35 C - OFF 65 C
-> Other settings upon request
- 2 Connecting alternatives (optional)
Connecting leads (AL) 0.5 m, 3 x 0.75 mm PVC
- > Other lengths upon request
Lead out terminal (DK) 0.08 - 2.5 mm
- Mounting position: vertical
- 2 fastening alternatives (optional)
Snap fitting for 35 mm DIN rail (figure 1)*
Screw fastening (figure 2)
|
|
PTC units for DIN bar application.
EH/FH heaters, installed separately from cooling unit, must be connected to TMC thermostat. When used to prevent cabinet condensate they should be eletrically connected also when cabinet is off.In this cabinet its better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
Heaters
Voltage: AC 220V
Power: 50W, 75W, 100W, 150W, 200W, 300W, 500W
Power frequency withstand voltage: 2kV
Operating life: 5 years
Temperature & humidity controllers
Power supply: AC220V}10%i50HZj
Withstand voltage: 2 kV
Controlled temperature precision: }1
Action humidity point: 93%RH or 80%RH
Range of target temperature: 5~15
|
|
Switchgear cabinet heating waterproof
Types: Wadi IP 65-AL, Wadi LH IP-65-AL
Tensions: 115V - 500V
Achievements: 180W - 380 W
Safety class system I (protective grounding) - enclosure IP 65
Temperature attitudes:
A 25C (35C) - from 55C (65C) (Eigentemperatur)
Other attitudes on request
Connection types:
Connecting cable (AL) 0,5m 3 x 0.75 mm PVC
Other lengths on request
|
|
| ... products without technical information |
| |
-Electronic ballast
-Lamp without/with electrical socket (choice of sockets)
-Magnet fixing (option)
-Energy saving lamp
-On/Off switch
The flat slimline lamp SL025 is suitable for all types of panels and enclosures, especially where space is at a premium.
The integrated electrical socket allows the use of additional appliances and is available in a number of country specific types.
The lamp can be mounted on its narrow or broad surface using screws and is suitable for fixing to 35mm DIN rails.
Approvals: UL File Nr. E 234324
|
|
-Slim casing
-Electronic ballast
-Lamp without/with electrical socket (choice of sockets)
-Magnet fixing (option)
-Energy saving lamp
-Automatic switching
The flat slimline lamp SL 025 with movement sensor is suitable for all types of panels and enclosures, especially where space is at a premium.
The lamp can be mounted on its narrow or broad surface using screws. It is also available with a magnet which allows it to be fitted quickly in any position in a steel enclosure.
Both versions are available with an integrated electrical socket enabling the use of additional appliances.
Approvals: UL File Nr. E 234324
|
|
Consistent, precise inspection results
Low inspection cost per part
Prompt equipment availability
Easy to upgrade through modular design
YXLON standard radioscopic X-ray inspection systems are the latest result of listening to customers and fulfilling their needs. The X-ray inspection systems are ideally suited for the inspection of a wide variety of test samples that include light metal die-castings, turbine engine parts, steel components, plastics and ceramics.
The multi-formatted X-ray inspection systems can be easily upgraded to allow digital image enhancement or even automated inspection sequences and image processing/archiving options.
The standard X-ray inspection systems are totally self-contained and can be located anywhere on the factory floor. Furthermore the X-ray inspection systems are designed for the operator's convenience and are easy to use.
|
|
For high columns in kitchen pantries as well as residential furniture, Schock offers a solution for load ratings of up to 120 kg. It is based on a ball bearing slide system which is mounted at the bottom of the cabinet below the extensible module.
Lateral stabilization is achieved by another full extension slide which is horizontally mounted on top of the module. In face of its high load capacity, the system provides a smooth movement without swaying.
An automatic self-closing device with integrated damper enables soft closing, even when fully laden. The opening force as well as the closing and damping action will be adjusted individually on demand.
|
|
|
|
see the results for the following category
