|
|
-Pressure clamp connectors
-Dynamic heating up
-Wide voltage range
-Temperature limiting
-Energy saving
-Clip fixing
-Quick installation
These heaters are used in enclosures where damage from condensation must be prevented, or where the temperature may not fall below a minimum value.
The aluminium profile heater body design has a chimney effect and distributes the heat evenly.
The pressure clamp connectors save time and simplify installation.
|
|
PTC Schaltschrankheizung
Types: P-ssm-Al, P10, P25, P65, P80
Tensions: 12V - 48V, 110V - 265V (wide rank)
Achievements: 10W - 300W
Safety class system II (protective grounding) - enclosure IP 54 (DK = IP 20)
Temperature behavior:
- self-regulating in dependence of the ambient temperature
- dynamic heating
Z.T. Exhaust for better air distribution mountable
Partly 2 connection types
Connecting cable (AL) with silicone cable 2X0,75 mm
Execution clamp (DK) 0.08 - 2.5 mm
Installation position perpendicularly
3 mounting options (alternatively)
Bolt mounting
DIN slides attachment
Attachment by means of thread groove
|
|
Low surface temperature
Quick mounting due to clip fixing
Double insulated (plastic)
Wide voltage range
Small size
Compact heater for the use in enclosures with electrical/electronical components. The design of the heater supports the natural convection which results in a high air-current of warm air.
The surface temperatures on the accessible side surfaces of the housing are kept down as a result of the heater design.
Our complete range of thermostats and hygrostats can directly be connected to the heater CS 060.
This heater is also available in a version with plug-in thermostat requiring no additional wiring (CSF 060).
Both versions are designed for permanent operation.
|
|
Heaters
Voltage: AC 220V
Power: 50W, 75W, 100W, 150W, 200W, 300W, 500W
Power frequency withstand voltage: 2kV
Operating life: 5 years
Temperature & humidity controllers
Power supply: AC220V}10%i50HZj
Withstand voltage: 2 kV
Controlled temperature precision: }1
Action humidity point: 93%RH or 80%RH
Range of target temperature: 5~15
|
|
Heaters for the thermo-regulation of enclosures, for application on DIN rail, and available in three version:
- with bipolar (15-30W) or three-pole (45-150W) power cable
- with three-pole terminal block (45-150W)
- ventilated (250-400W)
|
|
|
Condensation poses a particular risk for control electronics, especially with outdoor siting, but also indoors. Various different output categories ensure that the correct thermal output is always available. In this way, the total required thermal output can be distributed with complete accuracy within an enclosure.
|
|
Units for DIN or screw mounting.
TH heaters, installed separately from cooling unit, must be connected to a TMC thermostat. When used to prevent cabinet condensate they should be electrically connected also when cabinet is off.In this cabinet its better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
Technical details
- Protection class I (ground wire) - protection type IP 54 (DK = IP 20)
- Temperature setting:
ON 25 C - OFF 55 C (operating temperature of heating
system itself)*
Tropical version possible: ON 35 C - OFF 65 C
-> Other settings upon request
- 2 Connecting alternatives (optional)
Connecting leads (AL) 0.5 m, 3 x 0.75 mm PVC
- > Other lengths upon request
Lead out terminal (DK) 0.08 - 2.5 mm
- Mounting position: vertical
- 2 fastening alternatives (optional)
Snap fitting for 35 mm DIN rail (figure 1)*
Screw fastening (figure 2)
|
|
PTC units for DIN bar application.
EH/FH heaters, installed separately from cooling unit, must be connected to TMC thermostat. When used to prevent cabinet condensate they should be eletrically connected also when cabinet is off.In this cabinet its better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
Switchgear cabinet heating waterproof
Types: Wadi IP 65-AL, Wadi LH IP-65-AL
Tensions: 115V - 500V
Achievements: 180W - 380 W
Safety class system I (protective grounding) - enclosure IP 65
Temperature attitudes:
A 25C (35C) - from 55C (65C) (Eigentemperatur)
Other attitudes on request
Connection types:
Connecting cable (AL) 0,5m 3 x 0.75 mm PVC
Other lengths on request
|
|
| ... products without technical information |
| |
G12 - 12 Module Solution
Easy Glide Docking
* Provides an easy way of guiding a fixture into position prior to engagement
* Runners along the platform provide a smooth-sliding action
* Ideal feature when using large scale fixtures
Tabletop Configuration
* The tabletop configuration allows the S6 and G12 to be mounted to any horizontal surface
* Rear covers are available to protect wiring from the receiver to the test equipment
QuadraTrack Engagement
* Engaging Mechanism in the form of a pair of slotted steel slides located in the Receiver
* Distributes uniform pressure to four points on the ITA during engagement and disengagement
* Precise signal integrity between the Receiver and ITA is maintained by QuadraTrack engagement system
Slide Configuration
* The Slide Kits for the S6 and G12 allow access to test instrumentation and wiring
* Multiple Accessories are available for this configuration such as the Cable Tray and the Keyboard Tray Kit
|
|
This new concept of modular power connection allows a variety of applications, specifically adaptable to all users.
The wide range of current ratings available (40 to 1000 A) as well as the different levels of watertightness and shielding possibilities, offer connector solutions to numerous applications such as traction motors, converters, transformers, intercar power lines ...
|
|
one cabling solution for your equipment
- Ten sizes of cable ducting plus associated accessories.
- Optimal ducting sizes for maximum cabling capacity.
- Simplified installation:
- snap-off tongues for cable entry,
- 4 types of fixing accessories to suit the application: screw, clip-in, door mounting and chassis mounting.
- Important: no metal component parts enter the inside of the trunking, thus maintaining electrical insulation.
|
|
Dimensions acc. to IEC 60297 or IEEE 1101.1, Aluminum or sheet steel versions, up to superior EMC level. Large selection of assembly options.
|
|
Elma offers AC and DC horizontal enclosures in 2U and 5U heights and a DC-only version in 4U height. They include a wide range of backplane, shelf management,and other options. Pluggable and redundant fan trays, PEMs and shelf managers provide the highest level of availability (99.999%). The units have been optimized via backplane signal integrity studies and chassis thermal simulation.
The 2nd Gen 19" rackmount vertical ATCA chassis is designed for carrier-grade applications. The 13U chassis features a 14 -slot Dual Star or Mesh backplane. The unit is fully pluggable, designed for NEBS compliance, and radial or bussed IPMB shelf management. The chassis has been optimized via thermal simulation studies.
|
|
MicroTCA is complementary to PICMG3.0 ATCA. Where AdvancedTCA is optimized for very high capacity and high performance applications, MicroTCA is designed to address cost sensitive and physically smaller applications with lower capacity, performance, and perhaps less stringent availability requirements. MicroTCA preserves many of the important philosophies of AdvancedTCA, including basic interconnect topologies and management structure.
|
|
| ... products without technical information |
| |
-Slim casing
-Electronic ballast
-Lamp without/with electrical socket (choice of sockets)
-Magnet fixing (option)
-Energy saving lamp
-Automatic switching
The flat slimline lamp SL 025 with movement sensor is suitable for all types of panels and enclosures, especially where space is at a premium.
The lamp can be mounted on its narrow or broad surface using screws. It is also available with a magnet which allows it to be fitted quickly in any position in a steel enclosure.
Both versions are available with an integrated electrical socket enabling the use of additional appliances.
Approvals: UL File Nr. E 234324
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
Circulation fan for switchgear cabinets
With swing frames for the purposeful ventilation of heat sources in the switchgear cabinet
Housings and swing frames consist of steel sheet galvanized
Tensions: 12V - 230V
|
|
... see all the products in the category
Axial fans
|
| ... products without technical information |
| |
PETER electronic has added the compact type series VersiBrake 230/400-25 L (LP) to its tried and tested product line of electronic DC brakes. The device, which features an upgraded power section designed for a rated device current of 25 A, is available either as a housing version or as a circuit-board version for rated motor currents up to 12.5 A. In preparation for the certification by the German Trade Association (Technical Committee for Wood), VersiBrake 230/400-25L (LP) already now meets the association's requirements for category 2 acc. to EN 954-1. VersiBrake 230/400-25 L (LP) features double safety protection: i.e., control via motor contactor and motor voltage detection. In addition, a surge suppressor circuit and a braking current infinitely variable between 0 and the rated device current reduces the failure probability of the braking device and thus indirectly that of the machines, too. An integrated overload monitoring function, which, if the braking frequency is too high, prevents motor restart, provides safety both for the VersiBrake and the operator. The integrated and adaptable motor standstill detection gives the user flexibility with regard to the motor types available.
|
|
|
