|
|
INTERTEC offers the widest selection of explosion-proof heaters worldwide.
- ATEX/CENELEC approvals for Europe
- CSA/NRTL approvals for America
- GOST approvals for the Russian Federation
Our EX-heaters in combination with EX-controllers satisfy all requirements from freeze protection as well as high demands in the analyse technic.
For further questions please contact: Tel.+49-9445/9532-0
|
|
THERM HI "smart heater" is a system consisting of
an explosion-proof electric heater and a
microprocessor, designed to control the air
temperature in instrument enclosures and protective
cabinets and to limit the surface temperature of the
heater.
The "option E" is equipped with an intrinsically safe
sensor, thus allowing measurement and accurate
regulation of the temperature of the instruments and
equipment (e.g. of manifolds).
... THERM HI heaters are designed to solve
sophisticated and complex heating problems in
hazardous areas, and in particular for high
temperature maintenance of analyzing equipment.
|
|
Heaters for the thermo-regulation of enclosures, for application on DIN rail, and available in three version:
- with bipolar (15-30W) or three-pole (45-150W) power cable
- with three-pole terminal block (45-150W)
- ventilated (250-400W)
|
|
|
Condensation poses a particular risk for control electronics, especially with outdoor siting, but also indoors. Various different output categories ensure that the correct thermal output is always available. In this way, the total required thermal output can be distributed with complete accuracy within an enclosure.
|
|
Units for DIN or screw mounting.
TH heaters, installed separately from cooling unit, must be connected to a TMC thermostat. When used to prevent cabinet condensate they should be electrically connected also when cabinet is off.In this cabinet it’s better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
Technical details
- Protection class I (ground wire) - protection type IP 54 (DK = IP 20)
- Temperature setting:
ON 25 °C - OFF 55 °C (operating temperature of heating
system itself)*
Tropical version possible: ON 35 °C - OFF 65 °C
-> Other settings upon request
- 2 Connecting alternatives (optional)
Connecting leads (AL) 0.5 m, 3 x 0.75 mm² PVC
- > Other lengths upon request
Lead out terminal (DK) 0.08 - 2.5 mm²
- Mounting position: vertical
- 2 fastening alternatives (optional)
Snap fitting for 35 mm DIN rail (figure 1)*
Screw fastening (figure 2)
|
|
PTC units for DIN bar application.
EH/FH heaters, installed separately from cooling unit, must be connected to TMC thermostat. When used to prevent cabinet condensate they should be eletrically connected also when cabinet is off.In this cabinet it’s better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
Heaters
Compact heaters to keeping at a moderate temperature of cabinets and housings with electrical electronic installations.
In switchgear cabinets condensation with variations in temperature, which can lead to malfunctions or to losses of the components in the switchgear cabinet, forms. Heaters prevent subnormal temperatures and work against the emergence of condensation. Heater blowers provide additionally for the even distribution of warm interior air. The heaters are appropriate for continuous operation.
|
|
Technical details
• Protection class II (double insulated)
- protection type IP 54 (DK = IP 20)
• Temperature behavior:
· Self control, in variation of ambient temperature
· Dynamic heating-up
• Auxiliary fan attachable for improved air distribution
–> Auxiliary fan
• 2 Connecting alternatives (optional)
Connecting leads (AL) 0.5 m, 2 x 0.75 mm² Silikon
–> Other lengths upon request
Lead out terminal (DK) 0.08 - 2.5 mm²
• Mounting position: vertical
• 3 Fastening alternatives (optional)
|
|
-Pressure clamp connectors
-Dynamic heating up
-Wide voltage range
-Temperature limiting
-Energy saving
-Clip fixing
-Quick installation
These heaters are used in enclosures where damage from condensation must be prevented, or where the temperature may not fall below a minimum value.
The aluminium profile heater body design has a chimney effect and distributes the heat evenly.
The pressure clamp connectors save time and simplify installation.
|
|
Low surface temperature
Quick mounting due to clip fixing
Double insulated (plastic)
Wide voltage range
Small size
Compact heater for the use in enclosures with electrical/electronical components. The design of the heater supports the natural convection which results in a high air-current of warm air.
The surface temperatures on the accessible side surfaces of the housing are kept down as a result of the heater design.
Our complete range of thermostats and hygrostats can directly be connected to the heater CS 060.
This heater is also available in a version with plug-in thermostat requiring no additional wiring (CSF 060).
Both versions are designed for permanent operation.
|
|
Technical Details
• Protection class I (ground wire) - protection type IP 65
• Temperature setting:
ON 25 °C - OFF 55 °C (operating temperature of
heating system itself)
Tropical version possible: ON 35 °C - OFF 65 °C
–> Other settings upon request
• Connection
Connecting leads (AL) 0.5 m, 3 x 0.75 mm² PVC
–> Other lengths upon request
• Mounting position: vertical
• Fastening
|
|
AXENCL-9A & 9B EXPLOSION-PROOF ATEX CERTIFIED STAINLESS STEEL 12” & 18” CCTV CAMERA HOUSING (ENCLOSURE)
* Electro polished Stainless Steel with optional special corrosion proof paint for maximum corrosion protection
* Special steel glass for extra clarity and durability
* Certified to EEx d IIC T6 (ATEX Directive 94/9/EC)
* Fixed Mount – Bracket or Base installation
* Available in 12 inch and 18 inch versions
* Suitable for fixed or zoom lens cameras and integrated cameras
* Weather Resistant to IP68 (1.2 Mtrs) & NEMA 6 & 6P Standards
* Designed for use in extremely harsh environments and hazardous area locations
* Optional Sunshield
|
|
|
The explosion proof equipment has been designed to meet rigorous requirements and installations in hazardous areas, where flammable gases and powders may be present. All the EEX series has been certified to meet the ATEX, IECEx and GOST-R standards. The housing can accommodate most camera and lens combinations, while the P&T, thanks to the single multi-core pre-wired cable simplifies installation and maintenance. Videotec’s wide range of solutions are being utilised in explosive and hazardous atmospheres throughout the world.
|
|
Housing / Mounts / SnapPaks
Honeywell's housings and mounts are the perfect accessories to complete your camera installation, and have been designed to withstand the most demanding indoor and outdoor environments.
- HHC12 Series Housings - Medium Environmental Housing
- HHM Series Housing Mount Adapters - Housing Mount Adapters
- HHM Series Housing Mounts - Housing Mounts
- HBC5 Series - Indoor Camera Mounting Bracket
- ACUIX™ Mounts and Adapters - Parapet, Roof, Wall and Pendant Mounts
- SnapPak - Pre-Assembled Camera, Housing, and Lens Package
|
|
|
The VIDEOTEC housings have been produced using extrusions and die-castings with the highest quality aluminium and innovative technopolymer materials. These products are furnace painted with epoxypolyester powder colour, RAL9002, while the bolts and screws are in stainless steel. The numerous available accessories, like heater, camera power supply, blower and air filter, wiper and washer satisfy any installation requirement. The Hi-PoE housings have been developed to allow an easier installation of the IP and Megapixel cameras, using the High PoE (Power over Ethernet).
|
|
|
Most cameras are C-mount (1"-32t / 17.53mm flange distance). Some are CS-mount (1"-32t / 12.53mm flange distance) and can be converted to C-mount by adding a 5mm spacer. Earlier professional cameras came with an ENG mount (bayonet / 48mm flange distance). Lately, many of the more sophisticated cameras have the option of C-mount or F-mount (Nikon bayonet / 46.5mm flange distance).
|
|
|
|
|
|
16-channel hardware H.264 full D1 NVR with Core 2 Duo/Quad CPU and 4 internal storage drives
Features
* 16-channel analog video input
* H.264 AVC codec
* Socket LGA775 supports Core 2 Duo, Core 2 Quad CPUs
* 4 internal 3.5" SATA II HDD bays
* Slim DVD-RW drive
* 16-channel BNC looping
* Full D1 resolution
* 30FPS NTSC / 25FPS PAL per channel
Form Factor
2U Rackmount
H.264 Video Compression
H.264/AVC codec
Horizonatal Resolution: 720 pixels NTSC / 704 pixels PAL
Vertical Resolution: 480 lines NTSC / 576 lines PAL
NTSC: 30FPS per channel / PAL: 25FPS per channel
Audio
16 channel G.711 audio inputs via RCA connector (optional)
1Vp-p, 10Kohms input, 1 Vrms output
Platform
Supports Intel Core 2 Duo and Core 2 Quad CPUs, LGA775 socket
Intel Q35 + ICH9DO chipset
Storage
Four internal 3.5” SATA II HDD bays
Slim CD drive bay
HDD Interface SATA II x 6
RAID
Intel Rapid Recovery
System Memory
Dual-channel DDR2 DIMM 800/667 MHz
Max Capacity: 4GB
Socket: 240P DIMM x 2
OS Supported
Microsoft Windows XP
Ubuntu Linux 7.10
Fedora 7
Linux 2.6.18 ~ 2.6.25
Networking
Ethernet Ports RJ45 x 2 GbE (Intel 82573L)
Alarm/PTZ
PTZ Control 1 RS-485 for PTZ
Alarm Interface 8 DI and 8 DO terminal block
Compliance
CE Emission, FCC Class A, RoHS
Software
Evaluation Kit: EyeShot 2000 DVR Control Panel (Windows XP)
SDK: Linux and Windows SDK available
http://www.lannerinc.com
|
|
Model PVR-4450
4U Industrial Grade Rackmount DSS Platform
Adopts Intel® Matrix Storage Technology to support RAID 0/1/5/10
Support up to six PCI slots and one PCI-E x 16 slot
Support up to five HDD
Dual Gigabit Ethernet ports
Model PVR-2423
2U Industrial Grade Rackmount DSS Platform
Fantastic cooling design for CPU and add-on card
Remote control support
Dual Gigabit Ethernet ports
Model PVR-1140
1U Industrial Grade Rackmount DSS Platform with Dual Core Performance
Support Core Duo/Core Solo processor
Support PCI-E x 16 slot for Graphic card, PCI-E x 4 slot for RAID card and PCI slot for capture card
Adopts Intel® Matrix Storage Technology to support RAID 0/1(RAID 0/1/5/10)
Dual Gigabit Ethernet ports
|
|
|
The stainless steel special housings and P&T's have been designed to protect the cameras from particulary aggressive environmental conditions. They are entirely made of AISI 304 or AISI 316 stainless steel. In consideration of the extremely severe specifications, each detail has been carefully analysed, obtaining in this way very reliable products, suitable for industrial uses.
|
|
| ... products without technical information |
| |
 see the results for the following category : Axial fans |
|
|
