|
|
Heaters
Compact heaters to keeping at a moderate temperature of cabinets and housings with electrical electronic installations.
In switchgear cabinets condensation with variations in temperature, which can lead to malfunctions or to losses of the components in the switchgear cabinet, forms. Heaters prevent subnormal temperatures and work against the emergence of condensation. Heater blowers provide additionally for the even distribution of warm interior air. The heaters are appropriate for continuous operation.
|
|
Heaters for the thermo-regulation of enclosures, for application on DIN rail, and available in three version:
- with bipolar (15-30W) or three-pole (45-150W) power cable
- with three-pole terminal block (45-150W)
- ventilated (250-400W)
|
|
|
Condensation poses a particular risk for control electronics, especially with outdoor siting, but also indoors. Various different output categories ensure that the correct thermal output is always available. In this way, the total required thermal output can be distributed with complete accuracy within an enclosure.
|
|
INTERTEC offers the widest selection of explosion-proof heaters worldwide.
- ATEX/CENELEC approvals for Europe
- CSA/NRTL approvals for America
- GOST approvals for the Russian Federation
Our EX-heaters in combination with EX-controllers satisfy all requirements from freeze protection as well as high demands in the analyse technic.
For further questions please contact: Tel.+49-9445/9532-0
|
|
THERM HI "smart heater" is a system consisting of
an explosion-proof electric heater and a
microprocessor, designed to control the air
temperature in instrument enclosures and protective
cabinets and to limit the surface temperature of the
heater.
The "option E" is equipped with an intrinsically safe
sensor, thus allowing measurement and accurate
regulation of the temperature of the instruments and
equipment (e.g. of manifolds).
... THERM HI heaters are designed to solve
sophisticated and complex heating problems in
hazardous areas, and in particular for high
temperature maintenance of analyzing equipment.
|
|
-Pressure clamp connectors
-Dynamic heating up
-Wide voltage range
-Temperature limiting
-Energy saving
-Clip fixing
-Quick installation
These heaters are used in enclosures where damage from condensation must be prevented, or where the temperature may not fall below a minimum value.
The aluminium profile heater body design has a chimney effect and distributes the heat evenly.
The pressure clamp connectors save time and simplify installation.
|
|
Low surface temperature
Quick mounting due to clip fixing
Double insulated (plastic)
Wide voltage range
Small size
Compact heater for the use in enclosures with electrical/electronical components. The design of the heater supports the natural convection which results in a high air-current of warm air.
The surface temperatures on the accessible side surfaces of the housing are kept down as a result of the heater design.
Our complete range of thermostats and hygrostats can directly be connected to the heater CS 060.
This heater is also available in a version with plug-in thermostat requiring no additional wiring (CSF 060).
Both versions are designed for permanent operation.
|
|
Units for DIN or screw mounting.
TH heaters, installed separately from cooling unit, must be connected to a TMC thermostat. When used to prevent cabinet condensate they should be electrically connected also when cabinet is off.In this cabinet it’s better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
Technical details
- Protection class I (ground wire) - protection type IP 54 (DK = IP 20)
- Temperature setting:
ON 25 °C - OFF 55 °C (operating temperature of heating
system itself)*
Tropical version possible: ON 35 °C - OFF 65 °C
-> Other settings upon request
- 2 Connecting alternatives (optional)
Connecting leads (AL) 0.5 m, 3 x 0.75 mm² PVC
- > Other lengths upon request
Lead out terminal (DK) 0.08 - 2.5 mm²
- Mounting position: vertical
- 2 fastening alternatives (optional)
Snap fitting for 35 mm DIN rail (figure 1)*
Screw fastening (figure 2)
|
|
PTC units for DIN bar application.
EH/FH heaters, installed separately from cooling unit, must be connected to TMC thermostat. When used to prevent cabinet condensate they should be eletrically connected also when cabinet is off.In this cabinet it’s better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
Technical details
• Protection class II (double insulated)
- protection type IP 54 (DK = IP 20)
• Temperature behavior:
· Self control, in variation of ambient temperature
· Dynamic heating-up
• Auxiliary fan attachable for improved air distribution
–> Auxiliary fan
• 2 Connecting alternatives (optional)
Connecting leads (AL) 0.5 m, 2 x 0.75 mm² Silikon
–> Other lengths upon request
Lead out terminal (DK) 0.08 - 2.5 mm²
• Mounting position: vertical
• 3 Fastening alternatives (optional)
|
|
Technical Details
• Protection class I (ground wire) - protection type IP 65
• Temperature setting:
ON 25 °C - OFF 55 °C (operating temperature of
heating system itself)
Tropical version possible: ON 35 °C - OFF 65 °C
–> Other settings upon request
• Connection
Connecting leads (AL) 0.5 m, 3 x 0.75 mm² PVC
–> Other lengths upon request
• Mounting position: vertical
• Fastening
|
|
Internal dimensions :
4.5 m x 2.5 m x 2.0 m
Working temperature : 160°C
Control system :
Scheduler, regulator and recorder
|
|
- Applications: cooking, degassing, burning, polymerization, pre-heating, recovery, drying, stabilization, sterilization, vulcaniztion, tests,...
- 2 temperatures: 200°C maxi or 300°C maxi (depending on the option).
- Eight sizes: from 125 litres to 2520 liters.
Several options and accessories to adapt the oven to your needs.
|
|
|
|
|
|
The Qmax Series High Performance Reach-in forced-convection oven is specifically designed to meet the frequent air changes and tight temperature uniformity required of the ASTM 5423 Type I & Type II oven specification. A high-volume fan circulates air through perforated, stainless steel walls to create a constant horizontal airflow across all sections of the oven. The result is highly uniform airflow to easily meet ASTM 5423 Type I and II specification while tested according to ASTM 5374.
The Qmax Series High Performance Reach-in oven exceeds the ASTM 5423 Type II performance requirement a temperature variation of less than 6°C at 300°C while maintaining 100-200 air changes per hour. In addition, the brass bar thermal lag time showed superior oven temperature recovery. These ovens can be used for applications such as thermal evaluation of electrical insulating materials, testing, aging, curing, drying, sterilizing and other thermal applications where tight temperature uniformity is required.
|
|
Despatch RA and RF Series Reach-In Ovens feature uniform airflow and temperature consistency, ergonomic design, and smaller footprint
The Despatch RA Series and RF Series Reach-In High Performance Production Ovens have been used throughout the world for industrial production environments. These ovens are designed to provide process versatility, reliability and consistency in drying, curing, bonding and heat-treating applications. Ideal for use in industrial production environments, these ovens operate up to 650º F. The RA Series is designed for use in standard environments, and the RF Series is designed for Class A environments where flammable solvents are used. Despatch provides the design integrity, manufacturing experience and emphasis on quality necessary for dependable operation and excellent process control. To learn more please visit us at www.despatch.com or call our Product Specialists at 1-800-828-9903 Int'l 1-952-469-5424
|
|
| ... products without technical information |
| |
... see all the products in the category
Ovens
|
ARO controls are supplied in a complete range of welding cabinets to meet all requirements to 50/60 HZ or MFDC
Ease of use and reliabilility are the basic ingredients of the ARO control product range. Many variants and options guarantee efficient use for all types of applications.
Over and above the performance, reliability and ergonomic criteria of the work station, each of these products can solve cost reduction and control problems for the targeted application. In all cases, ARO provide solutions adapted to the specific requirements of each application and client.
In manual welding systems, the ARO Compact Welder is a popular solution and has the benefits of reduced installation time and cost. Products such as the AR 01, Micro 2x16 iii and ARONET are well proven, specially adapted to the application.
|
|
Drying locker for professional clothes. Closing by handle 1/4 of turn. To pose on the ground on feet jacks. Multiple punching of the lower part of the cell. Capacity from 2 to 3 complete equipments of work. Different specific models
230 V - 1100 Watts
|
|
|
Cupboard of drying. Manual or automatic Démarage. Drying with hot air with system of recycling of the air. Cleansing by ozone generator. Capacity from 30 to 70 pairs. Drying of the shoes or the gas masks. Time of drying: between 15 min and 2H00. Exist of them 30, 50 and 70 pairs. Stainless apparatus.
|
|
-Slim casing
-Electronic ballast
-Lamp without/with electrical socket (choice of sockets)
-Magnet fixing (option)
-Energy saving lamp
-Automatic switching
The flat slimline lamp SL 025 with movement sensor is suitable for all types of panels and enclosures, especially where space is at a premium.
The lamp can be mounted on its narrow or broad surface using screws. It is also available with a magnet which allows it to be fitted quickly in any position in a steel enclosure.
Both versions are available with an integrated electrical socket enabling the use of additional appliances.
Approvals: UL File Nr. E 234324
|
|
-Electronic ballast
-Lamp without/with electrical socket (choice of sockets)
-Magnet fixing (option)
-Energy saving lamp
-On/Off switch
The flat slimline lamp SL025 is suitable for all types of panels and enclosures, especially where space is at a premium.
The integrated electrical socket allows the use of additional appliances and is available in a number of country specific types.
The lamp can be mounted on its narrow or broad surface using screws and is suitable for fixing to 35mm DIN rails.
Approvals: UL File Nr. E 234324
|
|
Dryer desiccator cabinet KW.86/AV Series.
Internal chamber and shelves are in stainless steel; external cabinet in brushed AISI 0 stainless steel sheet and equipped with split opening door with sealing. Heating is achieved with specific air heaters; discharge of steam inside the chamber occurs by means of centrifugal electroaspirator with 0 m³/h flow rate.
The electrical system is provided with general switch and running light signal. Thermal stability is obtained through PID digital electronic μP regulator (with RTD Pt100 OHM input); it is paired with specific SSR, suited to absorbing load of heaters. In addition, each appliance is equipped with aerators and adjustable supports for shelving.
|
|
Vacuum drying cabinets serve for basic drying of temperature-sensitive concentrates and pasty mixtures of solid substances as well as granulates.
The properties of the dry product depend on the quantity of liquid they contain and the operating parameters which can be set on the equipment.
vacuum drying cabinetThe desired requirements can be controlled and adapted to the greatest extent with the drying process.
In comparison to other types of driers, vacuum drying cabinets offer optimum possibilities for influencing the drying characteristics.
|
|
Product group P3
Pivoting frame for directed ventilation
Electric data:
• Protection class I (ground wire)
• Protection type IP 20
• Connecting leads 0,5m 3x0,75 mm² PVC
Other lengths upon request
Utilizing a circulation fan avoids head accumulation and formation of heat pockets inside control cabinets. When heaters are installed, their efficiency is increased by circulation fans. The resulting air circulation dissipates heat through the surface of the cabinet and so, a cooling effect is achieved.
|
|
|
... see all the products in the category
Axial fans
|
For high columns in kitchen pantries as well as residential furniture, Schock offers a solution for load ratings of up to 120 kg. It is based on a ball bearing slide system which is mounted at the bottom of the cabinet below the extensible module.
Lateral stabilization is achieved by another full extension slide which is horizontally mounted on top of the module. In face of its high load capacity, the system provides a smooth movement without swaying.
An automatic self-closing device with integrated damper enables soft closing, even when fully laden. The opening force as well as the closing and damping action will be adjusted individually on demand.
|
|
. Reduced system
. IP 65 67
. Personalization with your needs
. Applications: boxes/cases, tables, cupboards, cabins/shelters
. Resistance to the vibrations, the shocks, the rodents, the cold heat/, fire, the products
|
|
COMPACT HIGH RESOLUTION DIGITAL RADIOSCOPY SYSTEM.
- Real time high resolution digital radioscopy
- Horizontal flat sample holder
- Motorized zoom axis
- Single image inspection of parts up to 24 cm long
- Very small footprint
- Ergonomic, fast and easy to use
Our equipements are customed-designed to best meet you needs.
|
|
|
|
|
|
FULLTEST4058 model was designed from HT ITALIA to performing essential tests in industrial environments on electrical machines devices and partially type-tested assemblies (PTTA) in compliance with EN60204-1 and EN60439-1 respectively.
The meter principally performing Continuity test on potential equalising conductors with >10AAC test current, Insulation Resistance with 500VDC test voltage and Withstanding tests with 1000AC test voltage (for electrical machine devices) and 2500V test voltage (for individual test on PTTA assemblies switchboards).
Withstanding test is performed also in BURN mode with no limits on trip-out current. Discharging Time measures of internal capacitance and on external plugs of device under test complete the list of possible test with this meter.As FULLTEST4050 more advanced model also FULLTEST4058 have a built-in internal memory to save all measurement results and a RS-232 PCs interface for directly transfer of saved tests by dedicated Windows software.
The model is fitted inside a practical and protected plastic case board with no flammability and a membrane keyboard for rapid selection of functions is included on the frontal panel together a wide custom display.
FULLTEST4058 is the ideal solution for any kind of verifier and/or industrial installer to performing easily and rapid test on industrial appliances.
|
|
|
|
see the results for the following category : 
