|
|
INTERTEC offers the widest selection of explosion-proof heaters worldwide.
- ATEX/CENELEC approvals for Europe
- CSA/NRTL approvals for America
- GOST approvals for the Russian Federation
Our EX-heaters in combination with EX-controllers satisfy all requirements from freeze protection as well as high demands in the analyse technic.
For further questions please contact: Tel.+49-9445/9532-0
|
|
THERM HI "smart heater" is a system consisting of
an explosion-proof electric heater and a
microprocessor, designed to control the air
temperature in instrument enclosures and protective
cabinets and to limit the surface temperature of the
heater.
The "option E" is equipped with an intrinsically safe
sensor, thus allowing measurement and accurate
regulation of the temperature of the instruments and
equipment (e.g. of manifolds).
... THERM HI heaters are designed to solve
sophisticated and complex heating problems in
hazardous areas, and in particular for high
temperature maintenance of analyzing equipment.
|
|
Heaters for the thermo-regulation of enclosures, for application on DIN rail, and available in three version:
- with bipolar (15-30W) or three-pole (45-150W) power cable
- with three-pole terminal block (45-150W)
- ventilated (250-400W)
|
|
|
Condensation poses a particular risk for control electronics, especially with outdoor siting, but also indoors. Various different output categories ensure that the correct thermal output is always available. In this way, the total required thermal output can be distributed with complete accuracy within an enclosure.
|
|
Units for DIN or screw mounting.
TH heaters, installed separately from cooling unit, must be connected to a TMC thermostat. When used to prevent cabinet condensate they should be electrically connected also when cabinet is off.In this cabinet its better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
Technical details
- Protection class I (ground wire) - protection type IP 54 (DK = IP 20)
- Temperature setting:
ON 25 C - OFF 55 C (operating temperature of heating
system itself)*
Tropical version possible: ON 35 C - OFF 65 C
-> Other settings upon request
- 2 Connecting alternatives (optional)
Connecting leads (AL) 0.5 m, 3 x 0.75 mm PVC
- > Other lengths upon request
Lead out terminal (DK) 0.08 - 2.5 mm
- Mounting position: vertical
- 2 fastening alternatives (optional)
Snap fitting for 35 mm DIN rail (figure 1)*
Screw fastening (figure 2)
|
|
PTC units for DIN bar application.
EH/FH heaters, installed separately from cooling unit, must be connected to TMC thermostat. When used to prevent cabinet condensate they should be eletrically connected also when cabinet is off.In this cabinet its better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
-Pressure clamp connectors
-Dynamic heating up
-Wide voltage range
-Temperature limiting
-Energy saving
-Clip fixing
-Quick installation
These heaters are used in enclosures where damage from condensation must be prevented, or where the temperature may not fall below a minimum value.
The aluminium profile heater body design has a chimney effect and distributes the heat evenly.
The pressure clamp connectors save time and simplify installation.
|
|
Heaters
Voltage: AC 220V
Power: 50W, 75W, 100W, 150W, 200W, 300W, 500W
Power frequency withstand voltage: 2kV
Operating life: 5 years
Temperature & humidity controllers
Power supply: AC220V}10%i50HZj
Withstand voltage: 2 kV
Controlled temperature precision: }1
Action humidity point: 93%RH or 80%RH
Range of target temperature: 5~15
|
|
PTC Schaltschrankheizung
Types: P-ssm-Al, P10, P25, P65, P80
Tensions: 12V - 48V, 110V - 265V (wide rank)
Achievements: 10W - 300W
Safety class system II (protective grounding) - enclosure IP 54 (DK = IP 20)
Temperature behavior:
- self-regulating in dependence of the ambient temperature
- dynamic heating
Z.T. Exhaust for better air distribution mountable
Partly 2 connection types
Connecting cable (AL) with silicone cable 2X0,75 mm
Execution clamp (DK) 0.08 - 2.5 mm
Installation position perpendicularly
3 mounting options (alternatively)
Bolt mounting
DIN slides attachment
Attachment by means of thread groove
|
|
Low surface temperature
Quick mounting due to clip fixing
Double insulated (plastic)
Wide voltage range
Small size
Compact heater for the use in enclosures with electrical/electronical components. The design of the heater supports the natural convection which results in a high air-current of warm air.
The surface temperatures on the accessible side surfaces of the housing are kept down as a result of the heater design.
Our complete range of thermostats and hygrostats can directly be connected to the heater CS 060.
This heater is also available in a version with plug-in thermostat requiring no additional wiring (CSF 060).
Both versions are designed for permanent operation.
|
|
Switchgear cabinet heating waterproof
Types: Wadi IP 65-AL, Wadi LH IP-65-AL
Tensions: 115V - 500V
Achievements: 180W - 380 W
Safety class system I (protective grounding) - enclosure IP 65
Temperature attitudes:
A 25C (35C) - from 55C (65C) (Eigentemperatur)
Other attitudes on request
Connection types:
Connecting cable (AL) 0,5m 3 x 0.75 mm PVC
Other lengths on request
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
-Large setting range
-Small size
-Simple to mount
-High switching performance
KTO 011:
Thermostat (normally closed); contact breaker for regulating heaters.
Approvals: UL File Nr. E164102
|
|
-Large setting range
-Small size
-Simple to mount
-High switching performance
KTS011:
Thermostat (normally open); contact maker for regulating of filter fans and heat exchangers or for switching signal devised when temperature limit has been exceeded.
Approvals: UL File Nr. E164102
|
|
Advanced Atmospheric Enclosure - AX-5000
Features:
- Fully computerized operation
- Historical and real time graphical display
- Independent vacuum pumping systems on all ovens and antechambers
- Integrated moisture, oxygen, argon, and helium monitoring
- Configurable modular design
The Unitek Benchmark AX5000 Atmospheric Enclosure is a rugged, tight, Windows computer-controlled atmospheric enclosure. It provides a safe, easy-to-access and easy-to-use enclosure optimized for hermetic sealing.
|
|
Advanced Atmospheric Enclosure - AX-5000
Features:
- Fully computerized operation
- Historical and real time graphical display
- Independent vacuum pumping systems on all ovens and antechambers
- Integrated moisture, oxygen, argon, and helium monitoring
- Configurable modular design
The Unitek Benchmark AX5000 Atmospheric Enclosure is a rugged, tight, Windows computer-controlled atmospheric enclosure. It provides a safe, easy-to-access and easy-to-use enclosure optimized for hermetic sealing.
|
|
Model PVR-4450
4U Industrial Grade Rackmount DSS Platform
Adopts Intel Matrix Storage Technology to support RAID 0/1/5/10
Support up to six PCI slots and one PCI-E x 16 slot
Support up to five HDD
Dual Gigabit Ethernet ports
Model PVR-2423
2U Industrial Grade Rackmount DSS Platform
Fantastic cooling design for CPU and add-on card
Remote control support
Dual Gigabit Ethernet ports
Model PVR-1140
1U Industrial Grade Rackmount DSS Platform with Dual Core Performance
Support Core Duo/Core Solo processor
Support PCI-E x 16 slot for Graphic card, PCI-E x 4 slot for RAID card and PCI slot for capture card
Adopts Intel Matrix Storage Technology to support RAID 0/1(RAID 0/1/5/10)
Dual Gigabit Ethernet ports
|
|
Outdoor housing VCM1353/00T
Features
Includes heater and blower
VC7H2725T includes factory pre installed camera and cable
Product Literature EN FR ES PT
Instruction Book
Observation Systems
Outdoor housing VCM1353/00T
|
|
|
Most cameras are C-mount (1"-32t / 17.53mm flange distance). Some are CS-mount (1"-32t / 12.53mm flange distance) and can be converted to C-mount by adding a 5mm spacer. Earlier professional cameras came with an ENG mount (bayonet / 48mm flange distance). Lately, many of the more sophisticated cameras have the option of C-mount or F-mount (Nikon bayonet / 46.5mm flange distance).
|
|
Here version SME of the system LockToo Access.
This offer "turn-key" exists in version 100 and 500 users.
Contents of LockToo Box Access:
- 1 biometric Reader LR (impressed only) or LRC (impressed + RFID)
- 1 Software of access control (BDD Access)
- 1 enrolor of office USB for the recording of the prints
- In option for models LRC: Coder of badges USB
Also available:
- LockToo Box Time
- LockToo Box Restaurant
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
Light isolation enclosure, mobile and disposable
Simple structure, easy assembly
Slanted panels for a better vision
Optimal air-tightness of the enclosure
|
|
|
