|
|
Modular high-performance CNC-turn-mill-centers
The UniCen is a turning and milling center with integrated B-axis where all requirements for complete machining have already been implemented: turning, milling, drilling and thread-cutting all on one machine. The workpiece is loaded on one machine only and can then be finished completely. With up to five interpolating axes even complex free form faces can be machined.
|
|
|
|
|
|
The Unicom 6000 machining centre is ideally suited for vertical turning and multi-sided machining of complex components. This highly flexible and powerful machining centre for complete machining results from the continuous development of vertical machining centres over a period of more than 25 years.
The concept of Unicom 6000 is based on a moving table with integrated carousel turning station and an interface that can receive pallets of up to 2.500 mm in diameter. The table movement is designated as Y-axis and it runs underneath a traverse with cross slide and spindle carrier. The movements of cross slide and spindle carrier are designated as X-and Z-axis respectively.
Unicom 6000:
4-Axes complete machining centre with HSK100-A interface, carousel turning station and pallet changer. The machine can be equipped with a right angular head or a universal head, in combination with C-axis mode in the carousel turning station.
Unicom 6000-HV:
5-Axes complete machining centre with carousel turning station, pallet changer and HSK 63-A interface in the integrated Unisign Nutator NC machining head as 5th axis, in combination with C-axis mode in the carousel turning station. This configuration is capable of 5-axes machining of complex components.
|
|
Highly productive milling-turning centers with one (MT) or two (MT-TWIN) milling spindles and one or two turning spindle(s) for complete machining of semi-finished products and saw sections.
Maximum workpiece quality by complete machining on one machining center. Workpiece clamping is done by means of clamping chuck or device.
The MT-S is designed for highest flexibility and ideal for small batches. The MT and MT-TWIN series offer maximum productivity for medium and large batches.
Reduction of costs per part by up to 30 % thanks to TWIN technology and 5-axes complete machining.
|
|
|
|
|
|
The Leonard machines are a complete and modular range of Horizontal Lathes for the machining on medium to large work pieces with highest performances in terms of rigidity for rough operations and precision for finishing operations. The main feature of these machines is the technology of the preloaded Hydrostatic ways which are successfully used for both cross and longitudinal slides.
Other machining operations can be performed with the Leonard system, like Boring, Milling or Drilling operations. The different working units can be Combined on a column with rotating base ("B" Axis) or on different Pallets to be manually or automatically installed in the carriage.
The Leonard lathe can be supplied with different type of Steady rests according to the work piece and the required machining.On demand different accessories are available like the work piece probe, the tool probe and the Automatic tool changer.
Safop has developed some special system for the measuring of high sophisticated work pieces like the turbine rotors. The Run Out Measurement System and Blade Measurement System are used with success by the main producers of this type of work pieces.
|
|
Drilling
Machining with coolant supply through the tool, regardless if the tool is in radial, axial or in an inclined position. Accuracy-killing changes between various machines is avoided.
Thanks to very high feed forces and high power also at low speed drills with large diameter can be used with optimum performance. A single look into the speed-power-diagram or the speed-torque-diagram shows the difference...
|
|
| ... products without technical information |
| |
PUMPS IMMERGEES 4 " to 24 "
BEACHES Of USE
Flows until: 2000 m3/h
Heights mano. until: 600 mCE
APPLICATIONS
Major drillings (until 300m), sumps, tanks, lakes, stoppings or rivers
Drinking water supply
Overpressure, irrigation, watering
Installations of treatment of water
Fire protection organization and sprinkler
Subterranean water folding back
Exploitation of geothermal energy
Platforms at sea...
ADVANTAGES
High hydraulic output and robustness, exceptional mechanics
Anti-corrosion wheels bronzes some without zinc
Great choice of materials: cast iron, spheroid cast iron, bronze without zinc...
Optimization of the characteristics by trimming of wheels
Non-return valve integrated according to model
Silicon carbide mechanical seal of higher quality
Engines available in 4 poles for one important lifespan, voltage until 6.000V
Engine rebobinable, temperature sensors
Horizontal or vertical installation
|
|
|
The pumps are employed for public water applications, water control at construction sites and in mines, and fountains. Our range of submersible pumps handles bore hole sizes from 8” to 12”, capacities up to 580 m3/h and heads up to 450 m.
|
|
LEROY-SOMER offers a huge range of centrifugal electropumps designed
for bore holes: drainage pumps, surface pumps with automatic
priming, submersible pumps.
|
|
SP4",6" and 8" submersible pumps are made of corrosion and abrasion resistant stainless steel and have been developed in accordance with state-of-the-art technology.The SP series of pumps are manufactured to the highest standards for energy efficiency,high performance,rugged construction and long service life for the most demanding applications.
Operating Limits
50Hz
- Capacity : max. 120m3/h
- Head : max. 432m
60Hz
- Capacity max.150 m3/h
- Head : max. 540m
- Liquid temperature : 0ﾟC to+60ﾟ
- Sand content : Max. 50g/ m3
Applications
- Residential Potable water supply from deep wells
- Municipal and industrial waters supply
- Irrigation and other agricultural applications
- Fire fighting systems
- Pressure boosting in high-rise buildings and other applications
|
|
|
C.R.I. Submersible Pumps are the products of the expertise from over four decades of experience, endurance and workmanship. These products are engineered to perfection with utmost care and stringent quality control at all stages to ensure a trouble free service.
|
|
Operating Limits:
-Max. liquid temperature: 35°C
-Min. diameter of well: 100mm
-Max. immersion depth: 100m
-Max. sand content: 0.25%
-Continuous duty
Motor:
-Rewindable enclosed induction motor or full obturated screen motor(n=2850r.p.m.)
-Built-in thermal overload protector with automatic reset
-Insulation Class B/F
-Protection IP68
Pump equipped with start control box or digital auto-control box
Material:
-External pump body: S.S AISI304
-Suction strainer: S.S AISI304
-Impeller: Noryl
-Diffuser: Noryl
-Shaft: S.S AISI304-C1045
-Motor housing: S.S AISI304
-Mechanical seal: Graphite-Sic/hard alloy
-Discharge body: Cast brass ASTM250 or Cast iron G20 UNI5007 or S.S AISI304
Application:
·Multistage submersible water pumps for 4" deep wells.
·Particularly suitable for civil and industrial purposes, such as applications to sprinkler and food plants, fire installations, etc.
·Water supply from wells or reservoirs, for garden use and irrigation.
|
|
Operating Limits:
-Max.liquid temperature:35°C
-Min.well ID: 132mm
-Max.immersion depth: 20m
-Continuous duty
Motor:
-Two-Pole induction motor(n=2900r.p.m.)
-Built-in thermal overload protector with automatic reset
-Insulation Class B/F
-Protection IP68
Material:
-External pump body: Stainless Steel
-Suction strainer: Stainless Steel
-Impeller and diffusors: Noryl
-Bearing brackets: Brass
-Shaft: Stainless Steel
-Motor housing: Stainless Steel
-Mechanical seal: Silicon/Silicon
Application:
·Multistage centrifugal submersible pump is applied to clean water drainage, especially widely used in irrigation system, drinking water supply, washing and similar applications where increased pressure is in need.
·It's stainless steel pump body and motor provide rust-resistance.
|
|
Operating Limits:
-Max.liquid temperature:35°C
-Min.well ID: 132mm
-Max.immersion depth: 20m
-Continuous duty
Motor:
-Two-Pole induction motor(n=2900r.p.m.)
-Built-in thermal overload protector with automatic reset
-Insulation Class B/F
-Protection IP68
Material:
-External pump body: Stainless Steel
-Suction strainer: Stainless Steel
-Impeller and diffusors: Noryl
-Bearing brackets: Brass
-Shaft: Stainless Steel
-Motor housing: Stainless Steel
-Mechanical seal: Silicon/Silicon
Application:
·Multistage centrifugal submersible pump is applied to clean water drainage, especially widely used in irrigation system, drinking water supply, washing and similar applications where increased pressure is in need.
·It's stainless steel pump body and motor provide rust-resistance.
|
|
Salient Features
* Pump is capable of handling sand laden or brackish or geothermal water with ease.
* Driven through a series of shafts supported by water lubricated rubber bearings, through drive head installed on ground level.
* Can be driven by an electric or Solar Powered Motor or Diesel Engine and provides option for changing pumps speed to match bore well yield.
* Smaller bore diameter reduces drilling costs.
* Flow rates unaffected by change in lavel of water table.
|
|
| ... products without technical information |
| |
The STAF®, the System of Casing Car-Borer, are a method of
pressure measuring drilling of type TFEM (Tube Split open with
Simultaneous removal of Materials) in accordance with standards NF P
94-110-1 and IN ISO 22476-4.
It is particularly recommended for the installation of the tube
split in the grounds known as of cover or not very homogeneous.
|
|
R25 Bit diameter 33 mm, 1 1/3 inch
Robit Rocktools Ltd, established 1985, is a Scandinavian manufacturer of high quality rock and ground drilling tools for construction, mining and quarrying
|
|
|
RHINO reaming shells sold at Fordia are manufactured with high-quality diamonds set into a high-strenght matrix, therby providing an excellent lifetime. The diamond-coated sections of the tool are cast directly onto the matrix and the reinforcement of the tool ensures maximum performance as the shell will maintain a full gauge hole in all types of ground.
|
|
Pilot adapters and reamers
Robit Rocktools Ltd, established 1985, is a Scandinavian manufacturer of high quality rock and ground drilling tools for construction, mining and quarrying.
|
|
SERCO PORTABLE MACHINING UNITS
The SERCO units are positioned and locked by means of a column/arm system clamped on the outer part of the surface to be machined (allowing internal machining). Machine set up is fast and easy. After a first visual positioning, we can get within a few minutes, using a simple specific device, a parallelism and concentricity within a 1/100 of mm precision. A powerful air motor drives the tool rotation (hydraulic motors on request) and radial automatic feed (with a selection of two speeds).
Maintenance
Flanges
Safety valves
Sealing valves
High pressure valves
Portable Equipment
Portable machining equipment
Portable boring and surfacing machines
Portable surfacing machines
Portable grinding machines
Portable lapping machines
For further information please contact :
PROTEM SAS
ZI LES BOSSES
F-26800 ETOILE SUR RHONE
FRANCE
Tel +33 4 75574141
email : n.reicher@protem.fr
|
|
The V-Lap F6 is standard equipped with a range of grinding and centre plates for grinding and lapping any type and size of ‘flat’ seat up to 6” / DN150 mm. The centre plate keeps the grinding plate in position, but also gives an eccentric rotation ensuring constant and complete coverage and absolute flatness.
Abrasives
The V-Lap F6 is completed with a large consumer quantity of polyester based, self-adhesive Aluminum Oxide round foil tips in grains rough, middle and fine. The foil tips can be used dry and on all common seat materials.
Drive machine
The V-Lap F6 is standard equipped with a battery drive machine and is delivered with 2 battery’s. The low weight and good balance of the machine increases the grinding performance and makes it easier to attain high quality flat ‘results’.
The complete set is packed in a robust, but light weight carrying case.
|
|
3 Axis 800 / 2000 / 4000
The machine is equipped with: one control panel, with an auto diagnostic display system, for the rotation and the feed of the arm and the milling cutter.
|
|
Alignment of bores in diesel engines, compressors, pumps, gearboxes, stern tubes and turbines
Proper repair and reconditioning of combustion engines, compressors and pumps requires exact measurement of the alignment of crankshaft and camshaft bores, cylinder bores and crosshead guides. This is usually accomplished by optical or wire-based methods. CENTRALIGN Ultra is a precision laser alignment system designed to replace those older and more time-consuming technologies. It is much faster, very precise, and provides a clear measurement protocol.
|
|
For straightness measurement of bores and bearing journals, both in production and in the field. Very stable construction for highest measurement accuracy. Measures both open and closed bearing pockets with equal simplicity. Handles up to 150 measurement positions.
Typical applications: Crankshaft and camshaft bearings in diesel engines, bearing journals and hull penetrations in propeller shaft installations, workpiece positioning in machine tools.
|
|
The L-705/L-706 laser systems are highly accurate, easy-to-use bore alignment lasers that can be used for virtually any bore alignment application. Bores ranging from 1.5" (38.1 mm) to 36" (914 mm) or more can easily be accommodated.
The L-705 is used for bore alignments out to 50 feet (15 M) and the L-706 is used from 50 to 110 feet (15 M to 33.5 M). Both lasers feature battery operation and micrometer-controlled angular adjustments, and both lasers are centered to their housings to within .0005" (.013 mm).
Our competitively priced L-705 Laser Borescope system is the fastest and most accurate extruder alignment system on the market. Its patented self-centering target and simple laser fixture are so easy to use you can have misalignment data in less than 10 minutes, including setup!
|
|
|
|
|
|
The AF_10 is a machining centre designed to cut to the utmost the time you have to dedicate to reinforcement fastening operations.
Because it features a loading roller conveyor and an unloading magazine, the bars are stored at exit. Once the profile has been inserted, movement, machining and unloading are all automatic. This way, the operator in charge of welding can take up the bars four at a time, thus cutting times down to the minimum. Or else the operator can dedicate him/herself with greater continuity to other operations required for the preparation of the welding bar.
The AF_10 offers various machining options: it permits having two screw pitch values and two distance values for the first screw from the outer point of the profile (tip of corner in case of 45° cuts, or outer point in case of 90° cuts for the crosspieces). What is more, it also carries out another operation of primary importance (selectable): because it has a lower motor, it drills frames for wall mounting preparation (or other jobs to be verified).
Finally, this is a machining centre which we recommend if you wish to increase the productivity of both a medium-sized workshop or an industrial workshop (in this latter case together with other machining centre and/or cutting/machining units)
|
|
The I.4F is an electro-pneumatic milling machinewith a vertical axis, fitted with a revolving head, equipped with four cutter-holding shafts.
This model allows you to fit four different cutting units with the relevant stops, and to use each time the required unit simply by turning the cutter-support head.
It is also supplied with orienting gripper to obtain cutting at 45° or intermediate angles.
The wide range of extra fittings allows very quick changes in working, saving time wastage caused by errors in setting up, by avoiding disassembly and assembly, with considerable increase in productivity.
|
|
|
|
see the results for the following category : 
