|
|
General:
NH 46/47 is a double acting stainless
acidproof hydraulic cylinder. Bore from
Ø 25 - Ø 100 mm.
Cylinder tube:
Stainless acidproof steel tube.
Piston rod:
Centerless ground stainless acid-proof
steel, wich is hard-chrome plated min.
20 μm.
Operation pressure:
Operation pressure: Max. 150 bar.
(water: 70 bar)
|
|
|
The further development of the BZ 500 leaves a lasting impression. The STZ is compact, easy to install and has a specially matched sealing and guiding facility called the Dipp-System®. The piston rods are hardened, ground and hard-chrome plated – an AHP Merkle quality standard!
|
|
We deliver a wide range of cylinder types, such as: Double acting cylinders
Single acting cylinders
Plunger cylinders
Double acting telescopic cylinders
Stainless steel cylinders, oli- and water hydraulic
Centre hole cylinders
ISO norm cylinders
Hydraulic cylinders with integreted transducer, inductive proximity switches etc.
Hydraulic cylinders with any integrated valves (build in valves)
Hydraulic special cylinders
DNV type approved hydraulic cylinders
GL type approved hydraulic cylinders
Special piston rod and tube materials
Special mountings
Hydraulic cylinders with special certificate
Special surface treatments
|
|
Standard
Operating pressure : max. 175 bar
Cylinder tube : Honed tubular steel
Piston rod : Centreless ground steel - hard chrome plated and
polished
Stroke : According to requirements
Seals: : Recognized make
Accessories : Trunnion mounting
Special
Operating pressure : more than 175 bar in special applications
Cylinder tube : Honed tubular steel
Piston rod : Centreless ground steel - hard chrome plated and
polished
Stroke : According to requirements
Seals : According to requirements
Mountings : All kind of mountings to customer request
Surface treatment : Sand blast, metallized, special coatings
and of course in all colors.
|
|
Rated to 2500 psi, 4000 shock pressure. Standard cylinders feature o-ring with polyurethane back-ups on piston and double lipped u-cup on rod. Full threaded rod through 1.25 diameter.
|
|
We deliver a wide range of cylinder types, such as: Double acting cylinders
Single acting cylinders
Plunger cylinders
Double acting telescopic cylinders
Stainless steel cylinders, oli- and water hydraulic
Centre hole cylinders
ISO norm cylinders
Hydraulic cylinders with integreted transducer, inductive proximity switches etc.
Hydraulic cylinders with any integrated valves (build in valves)
Hydraulic special cylinders
DNV type approved hydraulic cylinders
GL type approved hydraulic cylinders
Special piston rod and tube materials
Special mountings
Hydraulic cylinders with special certificate
Special surface treatments
|
|
Enlarge picture
HYA - **
• without cushioning
• max. working pressure 250 bar
Catalogue 7.10/D
German language
378 Kb
Enlarge picture
HYB - **
• with cushioning
• max. working pressure 250 bar
This design is according to steel and ironworks norm
Catalogue 7.10/D
German language
586 Kb
Enlarge picture
HYC - **
• with cushioning
• max. working pressure 250 bar
This design is according to Cetop-Europe-Standard
|
|
Cylinders Compact CHL and CHH
Description:
- Compact Hydraulic cylinders of "blocking" for double purpose allowing to apply forces up to 80,4 kN for maximum races de100mm by step of 5 and 10mm.
- Available for operating pressures of 100 bar, version CHL with body aluminum and 160 bar, version CHH with body steel.
- A magnetic detection is integrated out of standard for model CHL and option for model CHH.
- Detectors of position fit in the grooves of the body for the CHL.
Advantages:
- Cast solid Body.
- Great rigidity.
- Durable Coating corrosion resistant.
- Bearing unit of stem made safe by retainer, resistant to the vibrations: high frequencies applications.
- Reliability and easy maintenance.
- Unit /piston stem out of steel high resistor chrome hard.
- Piston made safe by joining and locating. Simple or double stem.
- Option grooves keying integrated eliminating the forces from shearing.
- Resistor with cutting oil by suitable nanomaterials of sealing.
- Model CHL incorporates out of standard a magnetic element.
- The detectors of position fit in the grooves of the body of cylinder.
Applications:
- Machine tools. Function of clamping, tightening, blocking, indexing.
- Perfectly adapted to the applications of cyclings to definite time.
|
|
Morin Series HP Hydraulic Actuator
Direct Gas/Hydraulic Actuators
Double Acting and Spring Return Models
1500 psig (103 bar) Operating Pressure Rating
Output Torque to 240,000 lb. in. (27115 Nm)
General Application
Designed for 'on-off' or modulating control of any quarter-turn ball, butterfly, rotary plug or damper style valve applications. For use in chemical process, food & beverage, iron & steel, off-shore marine, pharmaceutical, power, oil & gas, pulp & paper, and textile industries.
|
|
- Mill type design for applications even under extreme conditions
- Service-friendly modular system
- Various mounting types
- Interchangeability thanks to standardization
- Industry-specific and project-related cylinders on inquiry
|
|
CFC - Single acting, compact push cylinders with spring return
• Scrapers of polyurethane, positioned so that dirt can't penetrate in between piston rod and cylinder.
• Can be equipped with all kinds of NIKE accessories
CFC cylinders are real all-round cylinders. There are a large number of different CFC cylinders available with different characteristics such as capacity, stroke or height, which will meet your requirements. They have a compact design and a long stroke. The design gives small installation dimensions. CFC cylinders are provided with scrapers to keep the piston free from dirt.
Available in capacities ranging from 5 ton to 100 ton. Models of 5 t, 10 t, 15 t and 25 t can be equipped with an adapter for accessories.
All cylinders are designed for a max. working pressure of 70 MPa (in case there are some exceptions, these will be mentioned in the text above).
|
|
* Mounting of head and cap according to the tie rod principle
* Service-friendly modular system
* Small installation dimensions
* Various mounting types
* Interchangeability thanks to standardization
* Industry-specific and project-related cylinders on inquiry
Type CDT3...F
Nominal pressure: 160 bar
Piston Ø: 25 to 200 mm
Piston rod Ø: 12 to 140 mm
Mounting types: 13
Max. stroke length: 2700 mm
Max. stroke speed: 0.5 m/s
Type CST3...F
Nominal pressure: 160 bar
Piston Ø: 40 to 200 mm
Piston rod Ø: 28 to 140 mm
Mounting types: 5
Max. stroke length: 1400 mm
Max. stroke speed: 0.5 m/s
|
|
- Mounting of head and cap according to the tie rod principle
- Service-friendly modular system
- Small installation dimensions
- Various mounting types
- Interchangeability thanks to standardization
- Industry-specific and project-related cylinders on inquiry
|
|
Air chamber sizes are available from 12 to 36 square inches and hydraulic displacement from 1.0 to 9.0 cubic inches. Both remote and integral reservoir models are available for mineral base hydraulic oil or brake fluid.
|
|
according to the multiple helical gear principle
How many times did you already look for an actuator, which should make a
rotating or limited rotation in a small installation space? Many times?
Then can Eckart offer you, the current 250 bar actuator, the SM4 with his small, compact design as a ideal solution.
Size: 40 to 300 [mm]
Max. operating pressure: 250 [bar], higher on request
Max. torque: till 85.000 [Nm]
Angle of rotation: 90°, 180°, 270°, 360° and any intermediate angle, even above 360°
Temparatur range: -25°C to 70°C
Options: End cushioning, Longe-range adjustable end stop, Control switch assembly, locating pin, etc..
Special on request.
|
|
The HTR Series actuator incorporates many hydraulic and mechanical features that make this actuator suitable for high production applications. The Series actuators have been successfully employed in automotive plant production machinery; machine tool equipment; plastics and rubber processing machinery; basic metals production machinery and in material handling machinery.
Features:
Tapered Roller Bearings
Ductile Iron Housing
SAE Side Ports
Wear-Pak® Pistons and Seals
Chrome Alloy Steel Pinion and Rack Gears
Specifications:
Maximum Operating Pressure: 3000 psi(207 Bar) non-shock; except HTR22/45, 2000 psi(138 Bar) non-shock
Standard Rotations: 90°, 180°, 360°
Rotational Tolerance: -0°, +2°
Output Torques: 900 to 600,000 lb-in @ 3000 psi(204 Bar)
Maximum Breakaway Pressure: 70 psig(4.8 Bar)
Mounting Orientation: Unrestricted
Operating Temperature Range: -40 to 180°F(-40 to 82°C) Nitrile Seals; -20 to 250°F(-29 to 121°C) Fluorocarbon Seals
|
|
HTR Hydraulic Rotary Actuators The HTR Series are heavy duty hydraulic rack and pinion rotary actuators suitable for a wide variety of applications, including material handling and valve actuation, in industries as diverse as machine tools, primary metals, mining and oil field equipment.
Standard pressure: up to 210 bar
Standard rotational range of 90º, 180º and 360º
Options include port positions, cushioning, different seal types and mounting styles.
Special designs to customer specification
|
|
Sheer torque. Up to a 720° angle of rotation.
- High quality
- 0° to 720° angle of rotation
- Torques up to 1400 Nm
- Piston diameter 25 to 100 mm
|
|
Principle: rotary actuator after helical gear switch prinziple
combined with a linear cylinder
Size: 40 bis 125 [mm]
Max. allowable operating pressure: 160 [bar], higher on request
Torque: till 2.050 [Nm], higher on request
Angle of rotation: 90°, 180°, 270°, 360°, and any intermediate angle, even above 360°
Stroke: 0 to 1200 [mm], higher on request
Temperature range: -25°C to 70°C
Options: end cushioning, longe-range adjustable end stop, control switch assembly, locating pin, etc..
Special on request.
|
|
Our latest in our programm.
The application area is specially for low pressure-hydraulic with there typical pressure areas of 40, 60, 80 or 100 bar. The E1 works after the multiple helical gear prinziple and needs, in case of his compact construction, a small place.
Size: 40 bis 125 [mm]
Max. allowable operating pressure: 100 [bar]
Torque: till 2.450 [Nm]
Angle of rotation: 90°, 180°, 270°, 360°, and any intermediate angle, even above 360°
Temperature range: -25°C to 70°C
Options: end cushioning, longe-range adjustable end stop, control switch assembly, locating pin, etc..
Special on request.
|
|
The E3 actuator is specially constructed for mobile insert areas.
This actuator works after the helical gear prinziple and needs, in case of his compact construction, a small place. The Eckart E3 finds in most oft the industry sectors his mission: automative engineering, building- and underground machines, machine tools and so on.
Size: 95 bis 170 [mm]
Max. allowable operating pressure: 210 [bar], higher on request
Torque: till 3.600 [Nm]
Angle of rotation: 180°, 360°, and any intermediate angle, even above 360°
Temperature range: -25°C to 70°C
Options: valves, special on request.
|
|
When you use Parker Cylinder Genuine Replacement Parts, you are assured of the most up-to-date and reliable technology available.
|
|
HMI/HMD Gland Seal Kits Cylinder gland seal kits contain a replacement gland fitted with wiper and rod seals, plus a gland/head O-ring seal.
Supplied ready to fit, gland seal kits reduce machine downtime and avoid the risk of seal damage during installation of seals into the gland grooves.
A typical kit number, eg: RG2HM0221, denotes:
RG ~ Rod Gland kit
2HM ~ HMI/HMD series
022 ~ 50mm dia. rod
1 ~ standard seals, mineral oil, -20°C to 80°C temperature range
|
|
Hydraulic actuator
Simple or double effect - couple of 700 Nm with 200 Nm - Quarter of turn, linear or multitour.
Created in 2000 and established in North Isere (Villefontaine). We are specialized in the design and the distribution of materials and accessories of industrial valves and fittings.
A perfect knowledge of the products in varied fields (chemistry, oil, cryogenics, the hydroelectric one, engineering and maintenance), enables us to bring solutions adapted to your needs.
In addition to the delivery of the new material, we propose their installation as well as the handing-over in a state of existing material.
|
|
Fluids :
- Filtered and lubricated air.
- Mineral oil with viscosity between 16 and 160 cSt 40° C 25 µ nominal.
- Water, water solutions or emulsions.
Temperatures :
- 20°C +60°C (140° C HT mod.)
- As a torque generator, rotary actuator can not accept axial and/or radial loads.
- The use of mechanical stroke-end is advisable.
- E' consigliabile l'uso di fine corsa meccanici esterni.
|
|
| ... products without technical information |
| |
|
|
