|
|
KV 20 series valves are available from 1 to 9 sections. Manufactured for a flow rate of 150 lt/min and a maximum working pressure of 315 BAR; our KV20 series valves are designed for heavy duty tasks. Antishock and anticavitation valves are applicable. All sections include load hold check valve. Spools are hard crome plated.
Technical Characteristics
- Sections : 1 to 9
- Nominal Flow : 150 lt/min
- Max Operating Pressure : 315 Bar
- Max Back Pressure : 30 Bar
- Recomended Oil Viscosity : 5,4 - 11,4 CST (100°C)
- Recommended Oil Filtering : Max 30 micron
- Parallel & Series Circuit / Adjustable Direct Operated Relief Valve / Load Hold Check Valve in Each Section / Single - Double Action
|
|
KV 15 series sectional valves are available from 1 to 9 sections. Cast iron body. Antishock and anticavitation valves are applicable. All sections include load hold check valve. Spools are hard crome plated.
Technical Characteristics
- Sections : 1 to 9
- Nominal Flow : 80 lt/min
- Max Operating Pressure : 350 Bar
- Max Back Pressure : 30 Bar
- Recomended Oil Viscosity : 5,4 - 11,4 CST (100°C)
- Recommended Oil Filtering : Max 30 micron
- Parallel & Series Circuit Available / Adjustable Direct Operated Relief Valve / Load Hold Check Valve in Each Section / Single - Double Action
|
|
AST 08 valve is a specially designed auxiliary valve for Steyr tractors. The switch lever attached to the valve, enables it to control the single - double action hydraulic attachments on the tractor.
Technical Characteristics
- Nominal Flow : 45 lt/min
- Max Operating Pressure : 315 Bar
- Max Back Pressure : 30 Bar
- Recomended Oil Viscosity : 5,4 - 11,4 CST (100°C)
- Recommended Oil Filtering : Max 30 micron
- Parallel Circuit, Series Circuit Load Hold Check Valve Adjustable Direct Operated Relief Valve Single - Double Action
|
|
KVM 10 series monoblock type hydraulic valves have a nominal flow rate of 45 lpm and are being produced from 1 to 6 spools at 3/8" and 1/2" BSP.
Technical Characteristics
- Sections : 1 to 6
- Nominal Flow : 40 lt/min and 45 lt/min
- Max Operating Pressure : 350 Bar
- Max Back Pressure : 40 Bar
- Recomended Oil Viscosity : 5,4 - 11,4 CST (100°C)
- Recommended Oil Filtering : Max 30 micron
- Parallel &Series Circuit - Adjustable Direct Operated Relief Valve - Single / Double Action
|
|
SPOOL TYPE DIRECTIONAL VALVES
Our offer includes a wide selection of Spool type directional valves , whose variety of control ensures a wide range of applications
Moreover, we offer connection plates for all types of distributors and, upon the customer’s request, we take into account additional requirements.
Electro hydraulically controlled valves, depending on the order, may be provided with a switching time controller, a piston stroke restrictor or a limit switch. |
|
P70CP
Pump flow max 90 l/min (23,5 US GPM)
Workpressure max 320 bar (4600 psi)
The P70 directional control valve is of modular construction. It is designed for many different applications and used extensively in machines such as lorry cranes, small wheeled loaders and concrete placing cranes.
The valve can be of the directly operated type, or can be equipped for electric, pneumatic or hydraulic remote control. A combination of direct and remote control is also possible.
The P70 is stackable and can be supplied in combinations of 1 to 10 spool sections, and also in combination with function manifolds.
Low lever forces: give comfortable operation when the valve is controlled directly.
Mid-inlet sections: enable compact system design, even in systems with several pressure levels.
Very wide range of applicationadapted spools: designed to optimise control characteristics.
Our proportional remote-controlled valves have pressure compensated spools: which further improves control and simultaneous-operating characteristics.
Low pressure drops: keep down energy losses and reduce the generation of heat.
Machined land edges in the valve housing: guarantee good control characteristics. |
|
| The Directional Control Valve of the rotary spool type consists of a rotor which is rotated with respect to the valve body. When the rotor is placed in selected positions inlet and outlet ports are connected in various combinations permitting the start, stop or directional change of fluid under pressure. The functions specific to a valve depends primarily on rotor type selected. |
|
MODELS :
V2FIC02 Mounting (subplate)
V2FIC03 Mounting (subplate)
SIZES : 3/8 " TO 3/4"
Max. Pressure : 500 psi(350 bar)
FLOWS : 13 - 29 gpm / 50 - 110 lpm |
|
| Variable Flow Control Valves maintain the flow rate of hydraulic fluid to a selected value. Applications include hydraulic cylinders requiring constant extension or retraction speeds and hydraulic motors requiring constant rotational speeds. When used with a fixed delivery pump the excess flow is By-Passed across a relief valve. |
|
These 2/2-way ball seated directional valves are either directly or pilot actuated by a solenoid. With the directly actuated version the valve passage is opened or closed by a cone whereas with the piloted a piloting duct of a stepped piston is opened or closed generating a pressure difference at the opposing facial areas of the piston forcing it in the open or closed position.
Type EMP is a proportional valve, acting like a throttle but with zero leakage in blocked position. The dampened version will increase the switching time for on/off controls (hydraulic ramp). The wet armature solenoids for the valve actuation are pressure resistant, where all moving internal parts are flushed by oil.
There is a wide range of connection blocks either for pipe connection or for banjo bolt mounting, which may feature optional elements such as drain valve, by-pass throttle, pressure switch, 2-way flow control valve etc. |
|
Brake actuators
More safety, performance & reliability
Brake pressure proportional effort
For single & dual circuit
Small, lightweight package
|
|
The brake system onboard a vehicle is vital for the safety of the vehicle. It is therefore important that the design of the vehicle and the design of the brake system are co-ordinated to give the optimal safety and good performance and that complements other modern cab ergonomics to reduce operator fatigue and give good machine feel.
The valves may be used in open centre, closed centre and load sense hydraulic systems.
The high flow capability of the valve permit use with wet brakes, which typically require more flow for actuation.
Reduced mechanical drag and power loss by allowing the wet brake discs to be further apart when not applied.
A wide range of actuating forces can be specified, including stagemodulating springs for more progressive feel.
A floor-mounted pedal is available in a range of pre-set angles, with optional heel plates.
The valve may be mounted vertically or horizontally beneath the pedal. |
|
Moog's extensive experience in the application of cartridge valve technology enables us to offer a complete product line ranging from size 16 to 160. Sizes 16 to 100 are per DIN standard 24342.
In addition to our standard cartridge valves, Moog also offers a complete line of high flow, active, and servocartridge valves for specialized and higher performance fluid power systems.
Moog has application experience in Metal Forming and Presses Applications. |
|
Directional Control Valves Manually Operated RPR3-04
4/3 and 4/2 - way spool type directional control valves
Hand-lever operated
Actuating section can be rotated in four positions 90° apart
Installation dimensions acording to ISO 4401 CETOP-RP121H andNFPAT3.5.1 - D 02 |
|
Solenoid directional control on-off valves, atex valves and solenoid proportional valves
ARON has more than 25 years of experience in the hydraulic sector and since 2002 it has been a part of Brevini Fluid Power, a division of Brevini Group. A relevant part of the activity produces Cetop on/off valves and proportional valves, in different sizes (from NG4 to NG25).
The wide background knowledge, the accurate selection of suppliers, Research and Development activities and the excellent quality of the products – in terms of performances, cost and reliability – enable Aron to maintain a very important role on the market.
The Cetop range, recently completed with products suitable for applications in zones where explosive atmosphere may occur (Atex Directive), can satisfy every request of the mobile, agricultural and industrial markets, where innovation and quality are essential requirements.
|
|
| The PLC series auxiliary valves are direct-acting, factory-set pressure relief valves of the cartridge type that can be supplied with or without a threaded plug. They can also be supplied with housings to facilitate in-line installation. PLC valves are intended primarily to act as combined pressure-relief and anti-cavitation valves - otherwise known as port relief valves - in the service ports of our directional valves. However, they can also be used to advantage in other situations where pressure relief valves in this size range are required. Indeed, PLC cartridge valves are purchased in great quantities by several of the world%u2019s leading pump and transmission manufacturers. |
|
Pressure relief valve Prv 42
All hydraulic systems must be equipped with a pressure relief valve.
Sunfab in-line mounted pressure relief valve Prv protects the pump and hydraulic system
|
|
Moog is a leading designer, manufacturer and seller of high performance servo-valves, Servo-Proportional Valves, cartridge (poppet), directional and other hydraulic valves for industrial applications. For over 50 years, Moog's products have been the valve of choice for systems requiring a high degree of accuracy or precision. Also available are other hydraulic products such as integrated hydraulic manifold systems, radial piston pumps, electronics and accessories.
Our valves are known for long service life and when you need maintenance or repairs, ask for Moog Authentic Repair Services. |
|
| Barksdale's High Pressure OEM Valve line provides exceptional directional control for fluids up to 3000 psi in the toughest industrial applications. Using Barksdale's Shear-Seal® technology the OEM Valve products offer dependable performance and long life even when the media being controlled is contaminated with debris that would ruin ordinary valves. Flexibility is built into the OEM line which features several standard options that can be adapted to meet the unique needs that OEM customers require in their products. |
|
Your Hydraulic Control Solution!
• All valves are rated for 700 bar operating pressure
• All valves feature NPTF porting to insure against leakage at
rated pressure
• All valves are painted, coated, or plated for corrosion
resistance |
|
These directional seated valves use spring loaded balls as valve elements and therefore do not show any leakage. They are manifold mounting and are available with various actuations which always act on an angled lever pushing the valve element in the desired switching position.
The basic versions are designed as 2/2- and 3/2-way directional valves. 3/3- , 4/3-way functions are possible, if two valves are housed in one valve body, whereas 4/2-way functions require an additional intermediate plate. The enforced versions G39, G49, G..-22 are intended for pulsating, permanent load with frequent switching operations in the high pressure range.
These valves may be directly installed in pipe systems, when equipped with subplates enabling pipe connection. Many optional functions can be incorporated in these sub-plates e.g. pressure limiting valve or restrictor check valve for widen the field of application for this valve type. Valve banks of these valves are also available featuring several valves
connected in parallel (see type VB).
|
|
Valves
HYDRAULIC PUMP MOUNTED
3-WAY/3-POSITION (CLOSED CENTER)
NON-INTERFLOW MANUAL VALVE WITH “POSI-CHECK®”
Application – Single-acting cylinders. Actuation – Lever operated, detent positioned.
Functions – Pos. 1 – Oil is directed from pump to cylinder and “holds” with pump shut off; line to reservoir is blocked. Pos. 2 – All oil is open to reservoir through tank line.
Center pos. – Cylinder pressure is held; pump should be shut off.
Used on these pumps – P460, PA17, PA46, PA55, PA60, PE17, PE21, PE30, PE46, PE55, PE84, PE90, PE120, PE200, PE400, PQ60 and PQ120 series.
NOTE: A pressure switch and/or gauge may be attached if desired |
|
Proportional Directional Control Valves PRM2-04
Compact design with integrated electronics
High reliability
Simple replacement of the solenoid-coilsincluding electronics without opening the hydraulic circuits
Continuous flow control in both directions
nstallation dimensions acording toI SO 4401 CETOP - RP 121H and NFPA T3.5.1 - D 02
Subplates see data sheet HU 0002 |
|
| The seated valves are direct operated. Depending on the desired control function up to four valve cartridges are used. The poppets which are situated in the cartridge are pressed on the valve seat via springs or are opened via tappets. Hardened poppets and valve seats ensure long life. Pressure compensated poppets reduce the operating power. |
|
| The seated valves are direct operated. The balls which are situated in the cartridge are pressed on the valve seat via springs or are opened via tappets. Hardened balls and valve seats ensure long life. |
|
| Aron, a member of the Brevini Group, manufactures hydraulic components and manifold systems. The range of products includes Cetop components, related modular and proportional components, as well as electronic circuit boards, but the single and modular 6-way flow dividers deserve special mention. The sophisticated design of these parts make them ideally suited to a wide variety of applications, especially in agriculture. With a flow rate capacity of 20 to 80 lpm (5.3 to 21.1 gpm), this range is best suited to applications such as front loaders, mixer buckets, irrigator bars and other agricultural equipment in general, ensuring very limited pressure loss in relation to the performance delivered. Zinc plated versions are also available on request for use in particularly harsh conditions. |
|
Monoblock directional valves
Sectional body directional valves
Load sensing stackable directional control valves
Electric directional control valves monoblock and stackable
|
|
Types:
P.C. Flow Regulator
P.C. Flow Control
Priority Style P.C. Flow Regulator
Compensator Valves |
|
| B&G Flo-Control Valves are used for preventing gravity flow in forced water systems and to permit summer-winter operation of indirect water heaters. Flo-Control Valves in NPT sizes ¾" to 2" are made in combination straight-angle patterns permitting installation in either horizontal or vertical pipe lines. Larger sizes may be furnished in either straight or angle patterns. Removeable top cap allows easy cleaning and service without removing pipe connections. Manual operating position for vertical lift disc to permit gravity circulation. |
|
Types:
Two Way Spool Valves are available in Normally Closed and Normally Open types
Two Position, Three Way Spool Valves
Two Position, Four Way Spool Valves
Three Position, Four Way Spool Valve
|
|
|
|
