|
|
|
|
|
|
Cleanline portable light 4.2 gpm, up to 58 psi, FA 014
With the oil service unit FA 014 hydraulic or lubricating systems can be easily filled or deaned.
1. Compact design
The compact design allows easy access to the oil tank.
FA 014 comes ready to connect, with hose packages.
2. Economical
Efficiency through ARGO-HYTOS Fluid Management systems. After just a short time your investments will be amortized due to longer service intervals and increase of machine availability
3. User-friendly filter element change
Optimal operator handling has been a key feature in the development of FA 014. No extra tools are needed to open
the housing and the filter element can be pulled out through the hang-in technique.
4. Maintenance-free filter housing thanks to a clever filter element technique
On the bottom of the from inside to outside flown through filter elements there is a dirt retention valve. If the filter element is pulled out of the filter housing with the cover, the dirt retention
valve will close. Sedimented dirt is removed from the housing with the filter element.
5. Quality ¡n detail
The EXAPOR® fine element is the heart of the FA 014. High cleanliness levels protect hydraulic systems against dirt during the oil filling process.
73
|
|
Air Oil Separators
Our full range of traditional wrapped and pleated media separators deliver high filtration efficiency and longer life, plus boast greater energy efficiency too.
|
|
Application
In the high pressure circuits of hydraulic and lubricating oil systems.
Performance features
Protection
against wear: By means of ultra-fine filter elements that meet even
the highest demands regarding cleanliness classes and
dirt-holding capacity.
Protection against
malfunction: By means of permanent filtration in the off-line circuits
excellent cleanliness classes can be achieved.
Special design features
Cover: The cover can be opened without special auxiliary tools.
Because of the cover design the filter element can be
changed almost without losing any oil.
Flow control valve: Over the flow control valve the FNS off-line filters are
connected directly to the high pressure pipe. The surplus
volume (e. g. in circuits with fixed displacement pumps)
from the high-pressure circuit is cleaned by the ultra
fine filter element.
Dirt
retention valve: Ensures that dirt accumulated in the filter is removed
together with the element. Settled dirt cannot return
into the system.
|
|
Off-line filtration is in many cases the only feasible principle to achieve the required system cleanliness in fluid power systems. Off-line or kidney loop filter units consist of a circulation pump coupled to an appropriately sized and selected oil filter. The oil is circulated through this external filter system independent from the existing or non existing flow in the main system.
The programme comprises small compact standard units as well as customised subsystems of variable sizes.
Off - Line filter BNF series
Interchangeable DIN filter elements
Low noise emissions
Easy installation
May also be used for filling and draining the reservoir
Compact dimensions and easy to install either on the tank top or side. DIN elements provide qualified system cleanliness.
|
|
LANNER® systems
Complete chip treatment systems, built according to your requirements. LANNER® customised systems are available as a complete solution. Our systems can process different types of chip, silt and metalworking fluids with maximum separation.
The LANNER®-Recycling-Concept
Complete solution system concept separating oil from metal chips and silt.
Chips are fed into the lift & tip machine from the chip transporter.
Chips are tipped into the chip crusher.
Chips are transported into the centrifuge on the conveyor belt.
Dry chips are ejected into containers or silos.
The entire system is controlled automatically from a central control box.
|
|
BELL In-line Filters grant a high protection to the most delicate components of an oleodinamic system. Placed in the site under pressure, they keep the particles sucked or produced by the pump up to a size of 10 micron.
These filters are normally applied in addition to the standard filters in suction or release, as a last barrier of protection before the entrance in directional valves, flow regulating valves and all those components which require a high grade of absolute filtering.
The body is made in a treated aluminium alloy to obtain a minimum dimension and weight.
The filtering element, instead, is made in synthered bronze with a conic shape to resist to high pressure without collapsing.
|
|
High Pressure Single Strainer - Simplex T Type
The Simplex T Type extends the range of S type filters to higher pressures, suitable for both liquid and gas applications and available with bolted or quick release type covers.
Standard Features
Quick release covers eliminate the need for tools for maintenance.
Designed for pressure ratings up to ANSI class 300lb (900 PSIG).
Flow is from inside to outside the basket to trap and retain debris.
High basket area to pipeline CSA ratio of over 10:1 in most cases.
Can be fitted with coarse perforated baskets (2mm as standard) or fine stainless steel mesh inserts to give particle removal down to 50 microns.
Disposable depth type cartridges are available for filtration to 5~10 micron for liquid and 1~2 micron on gases.
|
|
98 Series Filters - High Pressure (10 micron)
98-1110 Series T-Type Filter:
Designed for high flow applications
Features cleanable element
Available options: electrical, visual, bypass valve, visual pressure differential indicator, bypass relief valve, electrical bypass
|
|
Simplex Type S
The general purpose standard, single basket filter with a quick-release cover for easy maintenance.
The design does not require specialised tools or knowledge, and results in a minimum of downtime.
Suitable for both liquid and gas applications.
Sizes: 1" to 12" bore, flanged to ANSI 125/250FF and 150/300 RF.
Can be drilled to BS tables and DIN standards.
Also available with screwed connections 1" and 1½" sizes.
Materials: Cast iron, cast steel and stainless steel, all fitted with cleanable baskets and inserts or disposable gas cartridges as required.
|
|
|
|
|
|
Hilliard brings fluid contamination problems under control – cost-effectively – with our full range of HILCO engineered products.
HILCO products:
• Reduce the cost of new oil purchases
• Decrease disposal costs
• Help lessen component wear
• Reduce downtime
• Help curtail environmental contamination
FILTER CARTRIDGES
• Microgard™
• Safegard™
• Pleated Synthetic Media PH Cartridges
• Hilsorb™ Dryer Cartridges
• High-Pressure Hydraulic Fluid
• Saflow™ and Saflow D™
• Pleated Screen Filter
• Pleated Strainer Baskets
• Backwash Strainers
• Hilite® and Hilite-A®
• Selexsorb®GT
• Coolant Coalescer and Oily Water Separater
• Fuel Coalescer Cartridge
• Fuel Separater Cartridge
• Bag Filter Cartridge
FILTER VESSELS
• Duplex Filter
• Integral Duplex Filter
• Standard Housings for High-Flow Synthetic elements
• Standard Non-Code Housing
• HILCO Transfer Valves
• Seal Gas Duplex Filter Housing
RECLAIMERS AND RECLAMATION SYSTEMS
• Standard HILCO Reclaimer
• Seal Oil Degasser
• Hyflow™ Reclaimer
• Machine Tool Coolant Recyclers
• Grinder Filtration System
OTHER HILCO PRODUCTS
• HILCO Ceramic Membrane Filtration System
• Portable Filters
• Star® Filter Press
• Storage Tanks
• HILCOSEP™ Coalescer
|
|
HILCO is one of the oldest filter equipment companies in the world with over 75 years experience in critical filtration and separation applications. We listen to our customer's needs and deliver quality engineered Hilco systems to meet the requirements, even if it is not something "off the shelf". We stand behind our products and will offer timely technical assistance.
HILCO Filters are compatible with the following fluid types:
• Insulating oil
• Lapping oil
• Hydraulic oil
• Fuel oil
• Seal oil
• Quench oil
• Draw oil
• Roll oil
• Cutting oil
• Edible oil
• Bearing packing grease
• Gear lube
• Lubricants
• Coolants
• Heat transfer fluid
• Fire-resistant synthetic fluids
• EHC (electrohydraulic control) fluids
• EDM coolants
• Per-flourinated polyester (fomblin fluids)
• Air filter liquid
• Ethylene
• Natural gas
• Nitrogen
• Butane
• Amine
• Phosphate esters
• Glycol
|
|
High Velocity Dual-Flow
Baldwin Filter High Velocity Dual-Flow lube filters provide improved engine protection during extended oil drain intervals, high idle time and harsh operating conditions. The patented design of the High Velocity Dual-Flow filters provides maximum filtration, while the heavy-duty construction ensures dependable operation.
|
|
The Fairchild Automatic Drain Filter Series is designed for use in systems that require clean, oil-free air. This series consists of a particulate filter and two coalescing filters with automatic drains. You can easily replace all filter elements.
Automatic Drain Filters are highly effective in removing oil and liquid-borne particulate matter. These units are recommended for use when clean air or inert gas environments are required in laboratory air, process control, instrument and compressed air systems.
|
|
Ikron %u201CFluid Filtration%u201D from Casappa %u201CFluid Power Design%u201D
An accurate filtration expands the life of all components and improves the overall efficiency of your hydraulic system.
Suction filters
Return filters
In line filters spin-on type
In line medium and high pressure filters
Accessories
|
|
System Features
Hydraulic oil even when new will have a certain level of particle
contamination, and is typically graded at ISO 17/13/14. When oil
is added to a system further contamination can occur. Whilst
under operating conditions air and moisture, as well as particles
from seals and hoses, can add to the contamination and
degradation of the oil. Fitting a Filtakleen filter will not only
reverse this process but it will clean your oil so thoroughly it will
be cleaner than when it was new!
|
|
- The hydro dry filter elements remove up to 80% of the free water present in the oil.
- Usable on RD, OF, PN and UOW filters.
- H2O retention capacity up to 2400 ml
|
|
|
|
|
|
HNP006 Series
FLUID CONDITIONING PURIFIERS
Fluid viscosities to 700cSt
Reliability of systems and the life of system components and fluids can be extended by minimizing water contamination.
The Pall HNP006 Purifier is designed to remove water from oil in low volume systems or where access for conditioning equipment is limited.
Benefits of Pall HNP006 Purifier
High-performance water, gas, and particulate removal
Simple automated operation
Extension of fluid life %u2022 120V single-phase electric connection
Extended fluid life
Minimized corrosion within systems
Increased equipment reliability
Reduced operating costs
Pall purifiers remove 100% of free water and in excess of 80% of dissolved water. They also remove 100% of free and entrained gases and in excess of 80% of dissolved gases.
The Pall HNP006 fluid conditioning purifier can be used as a fixed installation or portable unit that is easily removed and connected to any fluid system.
This compact purifier design is based on Pall's existing range of fluid conditioning products. It's size and weight allow for ease of handling through restricted openings and can be located close to existing systems where space is limited.
|
|
CONDENSATE CLEANER ACR 4
Motor capacity (HP/kW) 50
Condensate connection (input, '') 4 x 1/2
Water connection (output, ") 1 x 1
Oil connection (output) 1
Oil can (l) 5
Working temperature (min./max., ºC) 5 - 60
Dimensions (l x w x h, cm) 96.5 x 60 x 38
Weight (kg) 22
Ordernr: Code
36065 B
|
|
|
|
|
|
The Abanaki Model 8 Oil Grabber is a dependable and effective means of removing oil from water and water-base solutions. Often, skimming by itself will reduce oil to an acceptable level of water purity. Depending on the characteristics of the liquid, it is possible for the Model 8 alone to reduce oil content to less than five parts per million in water. The unit can be used as a pretreatment before filtration, and in conjunction with coalescing systems.
The Model 8 utilizes a continuous belt and wiper to remove up to 40 gallons of oil per hour from the fluid surface. The belt, operating on a motor and pulley system, runs through contaminated liquid to pick up oil from the surface. After traveling over the head pulley, the belt passes through tandem wiper blades where oil is scraped off both sides of the belt and discharged.
Oil skimming makes use of the differences in specific gravity and surface tension between oil and water. These physical characteristics allow the belt to attract oil and other hydrocarbon liquids from the surface of the fluid. The Model 8 can be used in tanks with depths as shallow as one foot, or as deep as 100 feet.
Advantages
- A single unit elevates and separates oil
- Lifts oil any distance without the need of expensive pumps
- Maintains skimming efficiency with fluctuating fluid level
- Can be used in depths as shallow as one foot, or as deep as 100 feet
- Requires no tank modifications in most applications
- Operates in turbulent liquid using optional tail pulley cage and tether assembly
- Easy mounting and fast cleaning, with minimal maintenance
|
|
|
|
|
|
Oil Grabber® Model 4
The Abanaki Model 4 Oil Grabber is a dependable and effective means of removing oil from water and water-base solutions. Often, skimming by itself will reduce oil to an acceptable level of water purity. Depending on the characteristics of the liquid, it is possible for the Model 4 alone to reduce oil content to less than five parts per million in water. The unit can be used as a pretreatment before filtration, and in conjunction with coalescing systems.
The Model 4 utilizes a continuous belt and wiper to remove up to 20 gallons of oil per hour from the fluid surface. The belt, operating on a motor and pulley system, runs through contaminated liquid to pick up oil from the surface. After traveling over the head pulley, the belt passes through tandem wiper blades where oil is scraped off both sides of the belt and discharged. The tail pulley has flanges which allow it to roll freely on the inside of the belt without becoming dislodged.
Oil skimming makes use of the differences in specific gravity and surface tension between oil and water. These physical characteristics allow the belt to attract oil and other hydrocarbon liquids from the surface of the fluid. The Model 4 can be used in tanks with depths as shallow as one foot, or as deep as 100 feet.
Advantages
- A single unit elevates and separates oil
- Lifts oil any distance without the need of expensive pumps
- Maintains skimming efficiency with fluctuating fluid levels
- Can be used in depths as shallow as one foot, or as deep as 100 feet
- Requires no tank modifications in most applications
- Easy mounting and fast cleaning, with minimal maintenance
|
|
|
We have named PUMP CARE the Suction Filters because thanks to their function of protection from coarse contamination (due to lack of initiai cleaning or to an accidental ingression) they take care of the pump, ensuring a safe and efficient operation.
|
|
A LARGE RANGE OF FILTERS
METAL EDGE FILTERS OR BACK FLUSHING FILTERS FOR
ECONOMICAL FILTRATION
Variable configuration inline pressure filters which use modern technology and can be deaned during on-going operation, require no maintenance or disposal measures as opposed to consumable filter material.
They can be used in applications ranging from fine filtration to coarse filtration.
|
|
|
Suction and delivery oil filters for both high and low pressures. EUROFILTRAZIONE is capable to supply you with original or equivalent filters of the leading international brands. Special filters are manufactured to customer specifications.
|
|
The MAHLE oil mist collector unit LGA 600 is a high performance oil mist collector unit for the separation of coolant from tooling machine exhaust air.
|
|
|
|
|
|
With over 3000 air/oil separator designs for compressors, Mikropor is one of the leading air/oil separator manufacturers in the world today.
The primary purpose of Mikropor air/oil separators in rotary screw and vane type air compressors is to separate oil from compressed air. Mikropor separators trap oil by allowing it to coalesce and drain down to a sump - while allowing compressed air to pass through. From the sump, oil will be removed by a scavenge line of some type and returned to the reservoir to be recompressed in a continuous cycle.
Mikropor separators are constructed of a depth loading media and have excellent oil removal capabilities that provide vital air/oil separation required in high-performing compressor systems. Mikropor separators have an oil removal rating of 1-2 ppm (parts per million) - so the oil loss in a compressor working with Mikropor air/oil separators is negligible.
Mikropor separators feature a unique Helix Tube Construction that provides added strength and collapse resistance.
In addition, some special Mikropor separators use fluted - not punched or perforated - steel. The flutes provide a diagonal air/oil flow and improve the coalescing performance of Mikropor separators over competitive products. This fluted steel design unique to Mikropor.
|
|
Coalescing Filter
M26
Features
• Manual Drain
• 0.01 Micron Rated Filter Element
• Quick-disconnect Bowl Guard with Integral Plastic
Bowl and Safety Latch
• Differential Pressure Indicator
Coalescing Filter
M21
Features
• Manual Drain
• 0.01 Micron Rated Filter Element
• Quick-disconnect Bowl Guard with Integral Plastic
Bowl and Safety Latch
• Differential Pressure Indicator
|
|
Applications
MANN+HUMMEL filters for compressed air systems ensure consistent performance of compressed air systems and systems installed downstream. They help to maximise the service life of all filters in the system.
Advantages
The advantages are
low oil and energy consumption
low wear in the compressed air system
custom-made solutions
different designs: air/oil separators, air-oil separator boxes, deep-bed filters, air/oil separators for vacuum pumps
|
|
Pressure Filters SF
STAUFF pressure filters are designed for the most demanding applications. They come in a variety of sizes, configurations and with numerous porting options.
* operating pressure to 420 bar
* flows to 1320 l/min
* BSP, NPT, SAE o-ring ports
or SAE flange (codes 61/62)
* filter head made of spheroidal graphite cast iron,
filter bowl made of cold drawn steel
* wide range of valve options
* various element types and media available
* standard bowls or top-loading bowls available
* visual, electrical and visual-electrical indicators
|
|
|
Our High Pressure series filters are designed for pressure line applications where design flexibility is required. Besides the standard T-Type and/or L-Type porting, we offer manifold type filters to provide compact and direct mount installation. This series is rated for flow from 50 to 150 gpm and a working pressure range from 4500 psi to 6000 psi.
|
|
Applications
Filtration lubricating oils and hydraulic fluids in engines and machines
Advantages
OEM quality
Proven technology
|
|
|
|
