|
|
Gear pumps and motors built in three pieces with an extruded body in high resistance aluminium alloy.
The wide choice of shafts, flanges and ports, in compliance with all international standards (SAE, DIN and EUROPEAN) allow for their use in an infinite variety of applications.
|
|
Gear motors made of cast iron in two pieces.
A rigid and compact structure that makes it possible to incorporate a number of functions in a limited space.
Wide range of displacements: from 0.30 in³/rev (4,95 cm³/rev) to 9.20 in³/rev (150,79 cm³/rev) available in groups 20, 30 and 40
Max. peak pressure up to 4785 psi (330 bar)
Max. speed up to 4000 min-1
|
|
When you need to produce and control high pressures, forces and torques permanently for mobile applications, then there are some pre-conditions:
- robust, service-friendly technology
- small size
- low weight
- as flexible multiple use of a component as possible
- easy handling and operation
The KRACHT mobile hydraulic components meet these requirements exemplarily. A glance at the technical data will convince you.
|
|
Gear motors made of cast iron in two pieces.
A rigid and compact structure that makes it possible to incorporate a number of functions in a limited space.
Wide range of displacements: from 0.30 in³/rev (4,95 cm³/rev) to 9.20 in³/rev (150,79 cm³/rev) available in groups 20, 30 and 40
Max. peak pressure up to 4785 psi (330 bar)
Max. speed up to 4000 min-1
|
|
Rated to 3000 psi. Spline or keyed shafts, side or rear porting, dual rotation available on standard models. Pressure balanced loading plates on either side of gears for maximum efficiency.
|
|
On this page you can download our brochures of the product line "Mobile Hydraulics".
When you need to produce and control high pressures, forces and torques permanently for mobile applications, then there are some pre-conditions:
- robust, service-friendly technology
- small size
- low weight
- as flexible multiple use of a component as possible
- easy handling and operation
The KRACHT mobile hydraulic components meet these requirements exemplarily. A glance at the technical data will convince you.
|
|
Single or Multiple configurations
Piggyback & Thru-Drive assemblies
Pressures to 4500psi
Pumps with flows to over 90gpm
Motors with outputs to over 150hp
|
|
|
External gear units are classic hydraulic units and come in the form of pumps and motors. Individual pumps, multiple pumps and lownoise SILENCE versions in seven different series open up a virtually unlimited range of possible uses.
|
|
Serie L - Aluminium body
Pumps
Motors
Flow dividers
Gear Pumps and Motors >> Serie G - Cast iron body
Pumps
Motors
|
|
SPEED VARIATOR
FEATURES
RELIABILITY
Stoutness and reliability guarantee long life.
PERFORMANCES
High torques at low speed, accurate and continuous speed adjustment. Frequent startings under load
RESISTANT
A system designed to work in difficult environments: with dust, humidity, overload, where electronics cannot stand.
ATEX
Easy to install in Atex ambient.
EMERGENCY
It's simple and cheap to control torque.
|
|
External gear motors, series APM
The essential components of series APM external gear motors are an aluminium alloy body and two gearwheels supported by plain bearings.
The front flange can be the SAE standard, or the British or German OEM patterns.
Particular attention has been focussed on the design of the shaft seal, which is often affected by back-pressures.
Advantages
- High overall efficiency thanks to optimised hydraulic compensation
- Optimum quality/price ratio
- Customised models can be built for specific applications
- Low maintenance requirements, even in heavy-duty operating conditions
- Various components and accessories are available for radial/axial loads, integral anti-cavitation valve, etc.
|
|
|
External gear units are classic hydraulic units and come in the form of pumps and motors. Individual pumps, multiple pumps and lownoise SILENCE versions in seven different series open up a virtually unlimited range of possible uses.
|
|
| ... products without technical information |
| |
The DOPAG ELDO-MIX range of gear pump driven metering and mixing systems are built in modular form and are custom designed.
Depending on the specific application, various basic configurations are available.
|
|
The Filament Winding DL is a two-component continuous-flow programmable-ratio meter, mix, and dispense machine for filament winding. The DL will supply accurately mixed resin/hardener systems directly to in-line composite processes. It is designed to easily fit into any production layout.
Features:
- Continuous feed of premixed resin/hardener
- Precision gear metering pumps
- Touch pad programming of mix ratios and flow rates
- Choice of several tank, drum or totes feed systems
|
|
Technical Data:
-Stainless steel frame
-Switch cabinet with controler, pneumatic and mechanics
-Feed part A direct from suppliers 50 litre open topped straight sided rums, follower-plate unit with 360mm diameter
-Feed part B direct from suppliers 50 litre open topped straight sided drums, follower-plate unit with 360mm diameter
-Metering pump with drive unit mounted on follower plate A
-Metering pump with drive unit mounted on follower plate B
-Low level cut off for both components
-Three-phase current motor
-Electronic adjustable dispense rate
-Electronic mixing ratio adjustment
-Pressure lines 250 bar
-Mixing block with dynamic and static mixing
-Purge with one component
-Swivel boom for mixing block
-Follower plate unit and Unidos 300 TX/MP machine are based on a zinc plated steel base with rollers
-Potlife alarm, adjustable time
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
