|
|
Gear pumps and motors built in three pieces with an extruded body in high resistance aluminium alloy.
The wide choice of shafts, flanges and ports, in compliance with all international standards (SAE, DIN and EUROPEAN) allow for their use in an infinite variety of applications.
|
|
Gear motors made of cast iron in two pieces.
A rigid and compact structure that makes it possible to incorporate a number of functions in a limited space.
Wide range of displacements: from 0.30 in³/rev (4,95 cm³/rev) to 9.20 in³/rev (150,79 cm³/rev) available in groups 20, 30 and 40
Max. peak pressure up to 4785 psi (330 bar)
Max. speed up to 4000 min-1
|
|
Single or Multiple configurations
Piggyback & Thru-Drive assemblies
Pressures to 4500psi
Pumps with flows to over 90gpm
Motors with outputs to over 150hp
|
|
When you need to produce and control high pressures, forces and torques permanently for mobile applications, then there are some pre-conditions:
- robust, service-friendly technology
- small size
- low weight
- as flexible multiple use of a component as possible
- easy handling and operation
The KRACHT mobile hydraulic components meet these requirements exemplarily. A glance at the technical data will convince you.
|
|
Serie L - Aluminium body
Pumps
Motors
Flow dividers
Gear Pumps and Motors >> Serie G - Cast iron body
Pumps
Motors
|
|
Gear motors made of cast iron in two pieces.
A rigid and compact structure that makes it possible to incorporate a number of functions in a limited space.
Wide range of displacements: from 0.30 in³/rev (4,95 cm³/rev) to 9.20 in³/rev (150,79 cm³/rev) available in groups 20, 30 and 40
Max. peak pressure up to 4785 psi (330 bar)
Max. speed up to 4000 min-1
|
|
Rated to 3000 psi. Spline or keyed shafts, side or rear porting, dual rotation available on standard models. Pressure balanced loading plates on either side of gears for maximum efficiency.
|
|
External gear motors, series APM
The essential components of series APM external gear motors are an aluminium alloy body and two gearwheels supported by plain bearings.
The front flange can be the SAE standard, or the British or German OEM patterns.
Particular attention has been focussed on the design of the shaft seal, which is often affected by back-pressures.
Advantages
- High overall efficiency thanks to optimised hydraulic compensation
- Optimum quality/price ratio
- Customised models can be built for specific applications
- Low maintenance requirements, even in heavy-duty operating conditions
- Various components and accessories are available for radial/axial loads, integral anti-cavitation valve, etc.
|
|
On this page you can download our brochures of the product line "Mobile Hydraulics".
When you need to produce and control high pressures, forces and torques permanently for mobile applications, then there are some pre-conditions:
- robust, service-friendly technology
- small size
- low weight
- as flexible multiple use of a component as possible
- easy handling and operation
The KRACHT mobile hydraulic components meet these requirements exemplarily. A glance at the technical data will convince you.
|
|
|
External gear units are classic hydraulic units and come in the form of pumps and motors. Individual pumps, multiple pumps and lownoise SILENCE versions in seven different series open up a virtually unlimited range of possible uses.
|
|
| ... products without technical information |
| |
|
Designed to operate at 50 hz motor speeds to eliminate need for a gear motor or reducer, these ductile iron internal gear pumps are well suited for chemical processing, grain processing and petroleum products. They may be foot mounted or close-coupled to IEC motors. The DIN seal chamber accepts many types of shaft seals.
|
|
PLEASE USE ENGLISH FOR ALL ENQUIRIES.
Enquiries written in other languages will not be answered.
|
|
Standard type
Gear ratios: 1:3 - 1:200
Max. permissible torque: up to 40Nm
Right-angle type
Gear ratios: 1:3 - 1:150
Max. permissible torque: up to 20Nm
Linear gearheads
Rack length: 100mm - 700mm
Max. permissible thrust force: up to 1400Nm
Feed speed: 10, 25, 45 and 50mm/sec
|
|
|
|
