|
|
6T press
Automatic blanking and bending press with toggle, featuring integrated programmable controller.
Designed as a stand-alone unit, yet ideal for integrating into a production line, automated with servomotor, with or without integrated numerical control.
Single or progressive dies (blanking, pressing) can produce several thousand parts an hour - exceptional reliability, precision and durability.
Material can be fed individually, in bar stocks or in strips. The machines comply with CE safety standards, are silent and clean, and can even be used in clean rooms.
|
|
Fine blanking press for precise stamped parts
Fine blanking press equipped with Decoiler, Roll feeder and straightening device*, fine blanking press and scrap cutter. On this unit there are produced precision stamping parts
Techn. data:
Coil weight: up to 2500 kg
Material: St
Thickness of material from 1,5 up to 6 mm
Width of material up to 300 mm
Production capacity: 10 up to 50 strokes per minute
Press capacity: 2000 kN
|
|
STANDARD FEATURES Steel welded frame
- Hydraulic system Bosch / Rexroth
- Electrical parts Siemens / Telemechanique
- Two hand control Start Button
- Emergency Stop Button
- Induction hardened and chrome plated column rods
- Two speed piston for moving plate at fast approach speed
- Automatic / Manual
OPTIONAL FEATURES
- Light curtain for safety
- Conformity to the EC Directives (CE)
- NC control
|
|
|
|
|
|
Hydraulic C-framed presses
Lower cost per part produced
The real saving here can be easily counted in production cost per part! The higher your hourly output is, the lower your unit production cost will be: in just a word, the advanced solutions built into Omera presses guarantee better productive performance.
Lower operating cost
Savings in operating costs are guaranteed because machine capacity can be exploited to the fullest without dead times caused by breakage or malfunction and maintenance operations can be programmed in advance with the assurance that everything has been made as simple as possible.
Quality = less production scrap, less wear on the dies
The first benefit of the trademark structural strength and constructive accuracy of Omera presses ensured by the highest design and manufacturing standards is the optimum performance of the tools, which can be translated in terms of defect-free production thanks to the uniform distribution of force throughout the productive process.
|
|
Hydraulic Press HWP 120 S
Try-out press for all tools and dies
This hydraulic try out press is used to determine the power requirements of dices.
Techn. data:
Press capacity: 1200 kN
|
|
Perforated Metal Production Line
TECHNICAL FEATURES Perforating press with pneumatic clutch
- Working width
- Capacity: 100 t
- Working Speed:350 stroke/min.
- Decoiler, feeding and straightening unit
MATERIAL APPLICATION
- SHEET METAL
- GALVANISED STEEL
- STAINLESS STEEL
- ALUMINUM
Corner Bead Production Line
- EXCELLENT DESIGN
- GOOD MACHINE
- QUALITY ASSURED PRODUCT
- COMPETITIVE PRODUCT
TECHNICAL FEATURES
- Production speed 18meter/min
- Material thickness:0.32mm -0.50mm
- Coil width:32mm-50mm
- Production space req�d: 2meter x 14 meter
- Total electric demand:10kW
|
|
Ursviken Frame Bender Type SBRP
Facts:
- The frame bender is a 4-way bending and straightening press.
- Bending bulbs, flats, tees and angles.
- Compact one piece design including hydraulic operation.
- Machining of, for instance, S-profiles including straightening without turning of the profile.
- Bending of flat bars with special tools.
- Step feeding of profiles, with free selection of the step length.
- Variable distance between anvils, always centric to the main cylinders.
- Simple and well adapted design of the control functions.
- All bending forces are internally absorbed, therefore no foundation is necessary - only simple attachment by bolts
- Automatic operation by teach-in programming
- Storing of programs, from single bending points up to complete bending programs, for repeating of similar bending programs by internal PLC.
- Modern system for e.g. trouble shooting.
|
|
BASIC FEATURES Steel welded structure
- High rigidity and straight side structure
- Stres relieving operation after welding
- Bosch-Rexroth Hydraulic system
- SIEMENS/MOELLER/TELEMECHANIQUE Electrical parts
- Two hand control button
- Upper � lower table parallelism
Perpendicularity of ram axis � lower table
Upper and lower table flatness
Rigid frame aganst to deflection
In International standards
- 8 Contact surfaces of ram table and side wall
- Manual/automic operation
- Painted surfaces from AKZO epoxy paint
OPTİONAL FEATURES
- Barrier for operator safety
- CE certificate
|
|
Monolithic hydraulic presses
The technologies applied in Omera presses that maximize system efficiency while permitting special types of machining let you lower production costs at the same time. The choice of the most appropriate model and configuration helps meet every productive need.
Reliability and technology
In addition to the components utilized, constructive quality, experience, and the technological choices made all grant our presses extraordinary reliability. Generous sizing and painstaking attention during machining also ensure the repeatability of the production process and the longest working life of the tools.
Applications
- water heater and tank bottoms
- cooking ranges
- electrical appliances
- beverage containers
- stainless steel pots and lids
- pressure vessels
- gas tanks
- fire extinguishers
|
|
|
|
|
|
Trimming machine model VBU 1200
For circular pieces up to 1200 mm. diameter, provided with: hydraulic power pack for the control of no. 04 working units; motorized spindle through gear motor and inverter; worked platform with %u201CT%u201D grooves for guiding and clamping of working unit;
Trimming machine model VBU 400
For circular pieces up to 400 mm diameter, provided with: hydraulic power pack for the control of no. 03 working units; motorized spindle through gear motor and inverter; worked platform with %u201CT%u201D grooves for guiding and clamping of working unit; structure for pieces clamping on the equipment
Trimming machine model VBU 400 R
Machine particularly suitable for the cold forming of pulleys, obtained starting from a plate, for trasmissions. The system is composed by: lower spindle mothorized by gear-box and inverter; loose upper spindle which is firmly connected to the four drive uprights;
Trimming machine model VBU 800
For circular pieces up to 800 mm diameter, provided with: hydraulic power pack for the control of no. 04 working units; motorized spindle through gear motor and inverter; worked platform with %u201CT%u201D grooves for guiding and clamping of working unit; structure for pieces clamping on the equipment
|
|
Trimming C-frame press for automotve parts
Trimming C-frame press completed with cutting tool for precise trimming of plastic parts for automotive industry.
Techn. data:
Cutting capacity: 250 kN
|
|
|
To leave d’ a standard base, for the needs related to the schedule of conditions customer, various functions and various installations can be realized.
|
|
SOCOPRESSES is with same, in partnership with you, to write the schedule of conditions related to a problem arising.
The selected technical solutions will be validated either by tests, or by preproductions on prototype tools.
|
|
Hydraulic press of routing (250 kN) equipped with a revolving plate.
Hydraulic press with swan neck of 100 kN with butted of race and revolving plate.
|
|
Today, our machines all are equipped with a terminal operator (IHM) of the tactile or traditional type. That makes it possible to safeguard the whole of the parameters of configuration, high race, slow speed, low of race and force (water pressure). The adjustment of the pushing force, as well as decompression are managed by a valve of pressure proportional.
By this principle, the changes of campaigns are simple and fast, we can safeguard approximately 50 programs according to the memory automat.
The hydraulic machines are equipped with distributers CETOP 06 or CETOP 10, the whole of the hydraulic material is assembled closest to the cylinder.
|
|
Models available:
=>Pressse hydraulic of 100 kN with butted of race and revolving plate.
hydraulic =>Press of stamping to swan neck doubles effect: 600 kN + 250 kN.
hydraulic =>Press 250 kN of rectification to swan neck to sensitive control.
|
|
The hydraulic machines with column have the advantage of becoming deformed very little; the deformation is primarily axial. They preserve, under effort, a parallelism of the tables higher and lower.
Like the machines with arcade, they are particularly suitable for the operations of loading by before and unloading by the back.
In options, we can equip them:
of a guided slide
of a greenhouse blank
of a mobile shutter of protection
etc...
|
|
presses hydraulics
Presses of 250 kN or 1000 kN flexible cutting of product with a slide guided on the columns.
|
|
Our standard machines are manufactured so that you can benefit from it best for your programs from production.
From a safety point of view:
The block of distribution is directly fixed on the cylinder in order to guarantee the position "high of race" whatever the mass of the tools (anti-falls).
The redundancy of the hydraulic and electric materials allows an increased safety.
|
|
PHC are open gap hydraulic presses, single or double action, for small and medium sized stamping and deep drawing jobs.
An amply dimensioned welded construction, very sturdy monoblock frame, and hydraulic driving by means of an axial piston pump with automatic output regulation guarantee reliability, productivity and precision.
Both tables have “T” slots for the easy and quick fixing of a very wide variety of tools.
For deep drawing jobs where the parts have to be removed, we recommend versions A with double action, i.e., with ejecting cushion.
|
|
Today, our machines all are equipped with a terminal operator (IHM) of the tactile or traditional type. That makes it possible to safeguard the whole of the parameters of configuration, high race, slow speed, low of race and force (water pressure). The adjustment of the pushing force, as well as decompression are managed by a valve of pressure proportional.
By this principle, the changes of campaigns are simple and fast, we can safeguard approximately 50 programs according to the memory automat.
The hydraulic machines with arcade have the advantage of becoming deformed very little; the deformation is primarily axial. They preserve, under effort, a parallelism of the tables higher and lower.
Like the machines with columns, they are particularly suitable for the operations of loading by before and unloading by the back.
|
|
Hydraulic press of stamping to arcade
with 4 effects: 2000 kN + 800 kN + 800 kN + 800 kN.
HYDRAULIC PRESS HAS ARCADE of 1000 kN.
|
|
|
5-Press line for manufacturing of wheel parts. The line consists of 5 x ZM presses, 6 x SpeedFeeders CD between the presses for maximum flexibility, 1 x blank destacker BF, safety system and a service platform.
|
|
AP&T has several production solutions for customers who require large volumes and details that require multiple operations.
This type of production solution is well suited for running cut blanks, circular as well as square, or for coil feeding directly into the press.
The tool set in this plant consist of several tools and tool changes are easily carried out through the long side of the press.
The hydraulic press runs continuously and has robust guidings for the best possible absorption of deflection forces.
The transfer feeder is especially designed for press automation with tool sets in multiple steps. The machine has three axes and is mounted directly on the press frame. The transfer feeder rails, where the gripper fingers are mounted, are easily exchanged when running different products.
The plant is equipped with an operator's terminal for optimal control and supervision of the entire press line. This terminal controls and supervises all machines in the line.
|
|
|
AP&T´s niche tools and production solutions are available in product areas like deep drawing, fire extinguishers, heat exchangers, pressure vessels and filter housings. The tooling for air duct parts include part types: saddles, elbows, reducers, bellmouths & endcaps. EU-standard - approx 120 part sizes. US standard - approx 170 part sizes.
|
|
|
|
