|
|
DVQ-25 DURABLE DESIGNED HIGH PRESSURE PUMP
The maximum pressue:250 bar
Displacement:18/22/26/32/38/43/47/52/52/60/65/75
Aplication:
Shoes making machine, Plastic and rubber molding mahcine,
press brake machine, press shear and steel sheet forming machine.
|
|
The MAXIMATOR air drive concept provides a number of benefits to you:
- Pressure regulation via manual pressure control units or pneumatically triggered valves
- Pressurised air drives, i.e. the pumps are particularly suitable for application in explosion-proof areas
- Stalling of the pump upon reaching the pre-selected ultimate pressure
- Substitution of leakages by automatic additional delivery of liquid from the pump
- No energy consumption during long pressure holding periods
- No heat loss during the pressure holding phase
- Easy installation and problem-free operation of the units. Only connections to air supply as well as suction and pressure lines are required
- Operationally reliable, easy-to-install and low-maintenance units, quiet in operation
MAXIMATOR provides competent consultancy, engineering design and supply of complete systems to optimally and economically solve your testing tasks and offers you extensive Services.
MAXIMATOR Pumps are available in 5 sizes: M, S, G, GX, DPD. The sizes vary according to their suitability for different pumping media, wide ranging flow rates and their maximum allowable operating pressures. MAXIMATOR provides the best-suited fluid pump for each application.
|
|
Feature:
Max. Pressure:245 kgf/cm2
Max. Speed :1800 RPM Min. Speed: 600 RPM
Application: Hydraulic press machine, fishing boat,
lift truck, plastic injection machine.
For detail product dimensions, performance characterisitics and order code, please visit our web site:www.kcl.com.tw
|
|
Serie L - Aluminium body
Pumps
Motors
Flow dividers
Gear Pumps and Motors >> Serie G - Cast iron body
Pumps
Motors
|
|
Rated to 3000 psi. Spline or keyed shafts, side or rear porting, dual rotation available on standard models. Pressure balanced loading plates on either side of gears for maximum efficiency.
|
|
* Chemical gear pumps GX series
Internal gear pumps incorporating fine ceramic gears
Max. discharge capacity: 35.2/42.5 L/min
Max. discharge pressure: 1.0 MPa
Main materials: SUS316, SiC, PTFE
* Chemical gear pumps GM series
Magnetic drive sealless type internal gear pumps
Max. discharge capacity: 35.2/42.5 L/min
Max. discharge pressure: 0.7 MPa
Main materials: SUS316, SiC, PTFE
* Chemical gear pumps GM-J series
Exclusively designed for sodium hypochlorite
Max. discharge capacity: 20 L/min
Max. discharge pressure: 0.5 MPa
Main materials: PVC, SiC, CFRETFE, PPS
* Magnetic drive gear pumps MDG series
Compact gear pumps that completely eliminate leakage problems
Max. discharge capacity: 14/17 L/min
Max. discharge pressure: 0.6 MPa
Main materials: SUS316, CFRPEEK, PPS
|
|
MDM is a wide ranging line of chemical process pumps designed to solve the most demanding chemical handling applications. Two materials of construction and convenient mounting configurations allow MDM to handle many aggressive chemical and high purity applications.
Unexpected dry running won’t damage the pump or interrupt the process. Our new design allows the pump to handle these situations with ease. High purity process fluid will not be contaminated by trace metals due to our combination of high purity materials and meticulous construction.
High strength rare earth magnets are totally encapsulated within fluororesin moldings. Small, lightweight and perfectly concentric magnet capsules optimize pump efficiency. An expanded temperature range (up to 300°F) as well as increased solids handling capabilities (up to 10%) provides users with solutions for their difficult applications.
Installation and maintenance time are reduced with our compact, close-coupled design. Operating costs are reduced thanks to simple, modular construction and individually replaceable parts.
|
|
Leakage free, sealless structure
The pump mechanism is the magnetic drive type. Free of leakage trouble, the pump is suitable to be incorpotated in various equipment.
Superior corrosion resistance
The wetted parts are manufactured from superior corrosion-resistant materials such as stainless steel, PPS, and PEEK. Therefore, the pump can be used to transfer various types of chemical solutions.
Long life design
Each part that is precision processed using Iwaki's original technology excels in thermal resistance, therefore does not cause pump troubles due to thermal expansion of the parts. Even when operated for long continuous hours, the pump should exhibit superior durability.
|
|
Our piston pumps is delivers high efficiency and low mantenance under the toughest operating conditions.
* Reliable fast response mechanism
* Special shaped fluid port reduces nosie
* High strength cast iron housing
* Designed to handle a various application.
For more model, specs. dimensions, please viist our
web site:www.kcl.com.tw
|
|
The PFVI series is a fixed displacement vane pumps for applications for industrial hydraulic equipment. The PFVI is a 12 vane design rotating group that has been engineered for quieter operation for the in-plant industrial environment.
The Parker fixed displacement vane pumps are of rugged cast-iron construction and are less sensitive to system contamination than most other hydraulic pump designs. The vane design produces a more smooth supply of oil that minimizes "hydraulic ripple". A desirable feature in all hydraulic systems.
PFVI vane pumps are hydraulically balanced designs that reduce bearing loads thereby minimizing maintenance and maximizing service life. The cartridge style design of the rotating group allows for quick and cost efficient servicing.
Combining this broad selection of fixed vane pump displacements and optional features with Parker's complete offering of gear, piston and variable vane pumps enables selection of the best pump for your demanding hydraulic requirements
|
|
The core parts of our adjustable systems are the pumps PA and PB. The flexible connections, which need only minimal space, as well as the possibility of attaching the pumps in any position even outside a system, gives the designer the possibility of installing the Ergoswiss System in very thin or complex objects.
Our pumps lift weights up to 1000 kg quietly, and are stepless and completely synchronous - even with an asymmetrical load. They are powered by an electric drive or a hand crank.
The pumps and cylinders are connected by a hydraulic hose (Ø 4 mm). The maximal hose length is 8m. The minimal bending radius 25 mm. Three attachment holes are provided fort he installation of the pumps. The pump housing is made of an extruded aluminium sheath and is colourless anodized.
|
|
FEATURES:
Full Pressure Shaft Seal — The Parker full pressure input shaft seal is able to withstand full system back pressure up to the pressure rating of the Hydraguide. This enables operation of auxiliary hydraulic functions downstream of steering.
Linear Valve Spool — The linear valve spool is less subject to stick and damage in the event of system contamination and allows generally better control.
Pressure Dams — Pressure dams provide a barrier of pressurized system oil between metered oil and return. Pressure dam valving provides more precise steering due to the reduction of lost leakage oil from the metering element.
Vaned Rotor — The spring biased vanes in the rotor tips reduce leakage between pockets in the metering group. This provides more precise and positive steering.
Pressure Balanced Metering Group — All Parker designs utilize a pressurized envelope around the metering package (rotor set—commutator) to reduce slippage leakage and provide more precise steering control.
Manual Emergency Steering — A ball check valve allows manual steering in emergencies when pump flow is interrupted. If the vehicle is large enough to require more than 100 ft.-lb. steering wheel torque in the manual mode, another means of emergency steering is recommended.
|
|
Our vairable displacemnet vane pump series have designed seven different out put flow for various
application. Such as 8, 12, 15, 20, 23, 26, 30 and
60 litre per minute at 1800 RPM
Pressure adjusting range:1. 5-18 kgf/cm2
2. 15-35 kgf/cm2
3. 30-55 kgf/cm2
4. 50-70 kgf/cm2
Application: CNC Machine Tool, special purpsoe machines
and all cuting machines.
For double pumps and all dimensions, please visit our
web site: www.kcl.com.tw
|
|
Model: 50 T and 150T
running speed from: Max. 1800 L/min. Min. 900 L/min.
Max. Pressure from 70 to 105 kgf/cm2
Delivery flow at no load pressure: from 9 to 139.6 L/min.
Application: special for surface grounding machine and
rubber machines.
For detail dimensions, performance characterisics please
visit our web site: www.kcl.com.tw
|
|
Model:
50T(low pressure) + VQ15(high pressure vane pump)
150T(low pressure) + VQ15(high pressure vane pump)
50T(low pressure) + PA(high pressure gear pump)
150T(low pressure) + PA(high pressure gear ppump)
This model design for customer's special application.
Please visit our web site: www.kcl.com.tw
|
|
Parker CK cartridge kits are used in the PFVI and PFVH series fixed displacement vane pumps for application on mobile and industrial hydraulic equipment. These cartridge kits are completely assembled and tested for quick and cost effective service of the pump in the field.
The CK**PFVH (mobile) is a 10 vane cartridge designed to meet the higher operating pressures and shaft speeds of mobile equipment and the CK**PFHI (industrial) is a 12 vane cartridge designed for use in the quieter in-plant environment. Flows from 5 to 60 GPM @ 1200 RPM with operating pressures to 3000 PSI can be achieved.
|
|
Variable displacement axial piston pumps swash plate design.
PLATA pumps are ideally suited for medium and high pressure open circuit applications
Displacements from 1.74 in³/rev (28,49 cm³/rev) to 5.37 in³/rev (87,9 cm³/rev)
Max. peak pressure up to 5075 psi (350 bar)
Max. speed up to 3000 min-1
|
|
The variable volume, pressure compensated design features of this pump combined with significant advancements in noise reduction make this pump a perfect match for many industrial applications.
The controls available provide for standard pressure compensation, load sensing, remote pressure control, and horsepower limiting. These control options permit the machine designer to utilize efficient pump controls that are tailored for the requirements of a hydraulic system. PVX controls are available in both single stage and two stage designs. All of the PVX controls exhibit very good response and recovery times and can incorporate a shock clipper that reduces shock pressure by up to 50%. This feature increases system component life and system stability.
The hydrodynamic journal bearing design is a feature that enhances the quiet operation of this pump, and eliminates the B-10 rating of the unit. A one piece rotor shaft contributes to this rugged design with minimized deflection when under high system loads. The rotor design allows the designer to easily configure a tandem mount rear drive option that provides the flexibility of driving multiple pumps with a common input shaft. This eliminates the need for additional prime movers, when multiple pumps are required.
Porting plates that provide proper timing for the inlet and discharge cycles of the pump, are designed for efficient and quiet operation. These pressure loaded port plates provide optimum running clearance to the rotor and contribute to high volumetric and overall efficiency.
Specifications
Mountings: SAE and ISO mounts
Capacities: 8 to 75 GPM
Operating Pressures: 200 to 3000 PSI
Recommended Fluids:
Petroleum-base, most phosphate esters, water emulsions and water glycol
|
|
Axial piston units are available in the form of pumps and motors in bent axis design or swashplate design for medium- and high-pressure ranges. They are the main components in the hydrostatic transmission. Compact size and high power density, economy and reliability are characteristic advantages which speak for the use of hydrostatic transmissions, together with the fact that they meet the demand for high speed and high torque, as well as optimum efficiency.
Characteristics:
- Open and/or closed circuit
- Displacement 5 to 1000 cm3
- Nominal pressure up to 450 bar
- Maximum speed up to 11,000 rpm
- Maximum power output 933 kW
Our versatile transmissions for mobile applications can be combined in a variety of ways with pumps, motors and open or closed loop control devices to offer the optimum design for every drive application and every power range.
Key advantages:
- Infinitely variable speed setting at fixed or variable input speed
- Immediate, jolt-free change in direction of rotation
- Simple, ergonomic operation
- High turnaround
- Automatic torque conversion
Axial piston pumps and motors are used for the travel drive and working hydraulics in a wide variety of mobile machines.
|
|
|
External gear units are classic hydraulic units and come in the form of pumps and motors. Individual pumps, multiple pumps and lownoise SILENCE versions in seven different series open up a virtually unlimited range of possible uses.
|
|
Axial piston units are available in the form of pumps and motors in bent axis design or swashplate design for medium- and high-pressure ranges. They are the main components in the hydrostatic transmission. Compact size and high power density, economy and reliability are characteristic advantages which speak for the use of hydrostatic transmissions, together with the fact that they meet the demand for high speed and high torque, as well as optimum efficiency.
|
|
Type PR4-Mini:
- Sizes 0.4 to 2.0
- Radial piston pump with 3 pistons
- Very compact build, hence installation-friendly dimensions
- 5 sizes
Type PR4:
- Sizes 1.6 to 20.0
- Radial piston pump with 3, 5 or 10 pistons
- Self-aspirating, valve-controlled
- Long bearing life due to hydro-dynamically lubricated plain bearings
- Several pressure ports with various cylinder combinations possible
- Optional combination with fixed and variable displacement vane and axial piston pumps
-14 sizes, favourable gradation for optimum matching to the application at hand
|
|
Vane pumps, fixed displacement
Types PVV, PVQ:
- Sizes 18 to 193
- Low operating noise
- Low flow pulsation
- Suitable for wide speed and viscosity ranges
- Combination of several pumps possible
- Can be combined with axial piston pumps and internal gear pumps
Vane pumps, direct operated
Type PV7...A:
- Sizes 10 to 25
- Very short control times
- Low operating noise
- Lower zero stroke power
- Mounting and connection dimensions according to VDMA 24 560/1 and ISO 3019/2
- Good efficiency
- Pump combination possible
Vane pumps, pilot operated
Type PV7:
- Sizes 14 to 150
- Variable displacement
- Low operating noise
- Pressure and flow can be controlled
- Controller actuator can optionally be locked
- Low hysteresis
- Very short control times
- Pump combination possible with standard pumps
- Mounting and connection dimensions according to VDMA 24 560/1 and ISO 3019/2
|
|
|
