|
|
The air-hydraulic BELL units are meant to operate single and double acting cylinders depending on the versions. This type of pump can be applied in all the hydraulic applications, especially in those which require high performances and pressures, and in all cases in which the oil flow must be modulated and controlled.
There are many applications, in the industiial field, such as stirrup, presses, extractors, pullers, hose fitting, bead breakers, clamping equipments, as well as in the automotive field for example car and motorbike lifts, pulling bars for bodyworks straightening benches.
|
|
|
The industry standard circulator for decades, Series 100 is still the one by which most others are judged. With well over 10 million units installed, the Series 100 remains a leader in applications such as hydronic heating and domestic hot water circulation. Series 100's three-piece, oil lubricated design provides for easy field service with bearings, shaft and seal all housed in an assembly which can be easily repaired or replaced. The Series 100 oil lubricated motor is specifically designed for the Series 100, and its resilient mounting provides quiet, dependable service with minimum annual lubrication. UL and CSA listings are standard. The design of this motor, coupled with its overall hydraulic performance, allows the Series 100 to overcome system related noise caused by valves, fittings, or piping.
|
|
The UPM pump by BELL is the right choice to operate continously or alternately single and double acting cylinders.
It is equipped with a retained control to work in standby for the pressurization of the circuit. The hand valve is a 4 way - 3 positions with open centre and standard CETOP 3 connection.
|
|
The HFP pump (Hydraulic Foot Pump) of BELL is made in steel to be strong, but also cheaper than other types of pump.
It is a sturdy pump characterized by a less stress on the lever, ideal for the use with hydraulic tools and/or single acting cylinders which require a small quantity of oil.
It does not require air-compressors nor other devices to work, therefore it is practical and easy to operate.
With a maxim relief valve inside, it is safe and avoids higher pressures of oil than the maximum pressure allowed (200bar).
|
|
BELL suggests and supplies the EUROPOWER hose 352 type for the whole range of pumps.
It is a flexible hose for great perfomances, created for higher mecanichal and dynamic standards, with a more longevity and excellent flexibility.
Particularly useful for hydraulic systems with very high pressure and it is compatible with hydraulic oils, lubricants, minerals and phosphats.
|
|
... see all the products in the category
Hoses
|
BELL In-line Filters grant a high protection to the most delicate components of an oleodinamic system. Placed in the site under pressure, they keep the particles sucked or produced by the pump up to a size of 10 micron.
These filters are normally applied in addition to the standard filters in suction or release, as a last barrier of protection before the entrance in directional valves, flow regulating valves and all those components which require a high grade of absolute filtering.
The body is made in a treated aluminium alloy to obtain a minimum dimension and weight.
The filtering element, instead, is made in synthered bronze with a conic shape to resist to high pressure without collapsing.
|
|
The circular sawing machine SC 45 by BELL is a perfect combination for the user who wants to saw the wood at the right length before splitting.
It is reliable and compact, a very good compromise among weight, size and log capacity, suitable for every kind of use.
One of the main feature is the wheels which allow to move the SC 45 very easily, another one is the telescopic rod which allow to load even longer wood logs, and the "set-size" rod which let the user saw all logs at the same length.
|
|
Atmosphere controlled bell furnace
Designed for aluminising and coating of steel alloy components
Complies with international aerospace standards
Operating temperature : 1200°C
Maximum process temperature 1150°C
Uniform operating zone within the retort : 1500mm (diameter) x 1150mm (high)
Maximum charge weight : 2500kg
Power rating : 250kW
Supplied with 2 walking hearths and an overhead furnace transfer system
Fully programmable gas system with vacuum purge facilities
|
|
Bell furnace for heat treatments:
normalizing
annealing
tempering
Plant design according to Customer requierments by team of qualified engineers
- Construction and assembly undertaken by specialised personnel
- Plant commissioning and production assistance on a "Turnkey" basis
- After-Sales Service
- Repair and maintenance intervention on site
- Supply of spare parts
- Technical consultancy services, including operating improvment and calibration
|
|
|
This Wellman Furnace is used for annealing, brazing, stress relieving, oxide reduction and sintering. Vacuum or controlled atmospheres are available.
|
|
REMOVABLE COVER WITH BOGIE HEARTH FURNACE FOR OVER HARDENING
Electric furnace
Power : 900 Kw
Temperature : 1150°C
COVER FURNACE WITH 2 BOGIE HEARTS
Electric heating
Annealing under atmosphere
Power : 300 Kw
Loading capacity : 4000 Kg
Temperature : 950°C
|
|
Electric Bell Furnace
The Lindberg Rod Overbend (RO) Element Bell Furnaces give you flexible, efficient performance in a variety of heat-treating applications. The fast heating rate, heavy load capacity, and reliable operation help you achieve fast turnaround and high productivity. The furnace is very simple and economical to operate, and is available in a wide range of sizes.
Features / Benefits
Standard endothermic atmosphere system
Emergency nitrogen gas purge circuit activates on power failure or loss of atmosphere
Atmosphere tight continuously welded hood assembly
Low watt-density RO elements for long life
RO elements have round cross-section for excellent long-term stability with minimal resistance to change
Easy-loading chamber
Complete, pre-wired free standing control panel with disconnect switch
SCR power control
Excess temperature instrument
Designed to meet FM, IRI, OSHA, and NFPA requirements
Ceramic fiber block insulation reduces power consumption and boosts your productivity and efficiency with faster thermal cycling and reduced heat loss
Guide posts to ensure proper alignment of heating bell on base
Applications
Annealing
Austempering
Carbonitriding
Carburizing
Hardening
Martempering
Preheating
Solution Treating
Stress Relieving
Tempering
Normalizing
|
|
| ... products without technical information |
| |
|
... see all the products in the category
Furnaces
|
RAD-CON Inc. specializes in bell-type batch annealing furnaces for the ferrous and non-ferrous, wire and strip industries. RAD-CON is a global leader in bell-type batch annealing technology, with installations worldwide.
Our vacuum purge system rapidly reduces the contaminant levels to facilitate the brightest finish possible. Systems can operate using 100% hydrogen or a mixture of hydrogen and nitrogen to accommodate a variety of alloys. RAD-CON’s team of engineers, metallurgists, and technicians work closely with non-ferrous customers to support and optimize their cycles based on the needs of copper and brass annealing.
|
|
RAD-CON Inc. specializes in bell-type batch annealing furnaces for the ferrous and non-ferrous, wire and strip industries. RAD-CON is a global leader in bell-type batch annealing technology, with installations worldwide.
RAD-CON is the premier choice for Cold-Heading Quality wire producers. The 100% Hydrogen Super-High Convection™ system along with the AC/APEx™ atmosphere control system increase productivity while lowering operating costs. These innovative and proven technologies coupled with economical solutions to customers’ applications make RAD-CON the preferred brand for CHQ.
RAD-CON also services other steel wire processors. RAD-CON designs the best possible solution for specific annealing requirements based upon the customers’ needs. Providing 100% hydrogen systems, nitrogen systems, direct-fired furnaces or radiant-tubes, RAD-CON has a design for any situation.
|
|
|
RAD-CON Inc. specializes in bell-type batch annealing furnaces for the ferrous and non-ferrous, wire and strip industries. RAD-CON is a global leader in bell-type batch annealing technology, with installations worldwide.
|
|
|
LOI is the world leader in HPH (High Performance Hydrogen) bell-type annealing plants. More than 2,000 HPH annealing basis have now been installed throughout the world
|
|
| ... products without technical information |
| |
A full range of manual shrinwrapping machines with the best ratio price/performance. Four models with the same features aimed at satisfying customers having different needs. Six working programs available directly by the electronic control panel that drive all machine functions.
Patented system with transparent hood to get both sealing and shrinking in one only operation (without tunnel); sealing at impulse adjustable blade, security thermostat with warning signal to find out troubleshootings, two working positions (sealing only or sealing+shrinking), sliding trolley and adjustable working surface, micropuncher included.
|
|
This model is the culmination of years of experience and knowledge gained by Minipack in its aim at optimising and improving airflow in its chamber machines .
Synthesis inox is ideal to pack pizza, bread, cookies and pastries.
The new worldwide patented ventilation system placed on machine rear allows a steady temperature without overheating.
Easy wipe clean due to absence of motors, of fans and felt on chamber botton, greater efficiency with different kinds of film; sealing + shrinking or sealing only modes, up to 20% power savings.
|
|
| ... products without technical information |
| |
PPH 308 - Automatic bell spraying with rotating bell
The PPH 308 automatic bell atomizer use centrifugal force to ensure uniformity, deep penetration and spraying.
With their spraying fineness, transfert efficiency and ease of implementation and adjustment, the PPH spray guns guarantee both a high level of productivity and a superb quality finish.
The PPH 308, equipped with magnetic turbine has been designed for the electrostatic application of water or solvent-borne liquid paints in general industry.
Equipped with EC 65 bell specially designed for the application of high solids and metallic paints electrostatically.
|
|
|
A closed loop current sensor consists of a Hall generator mounted in an air gap of a magnetic core, a coil wound around the core and a current amplifier.The current carrying conductor placed through the aperture of the sensor produces a magnetic field that is proportionate to the current. This field is concentrated by the core and sensed by the Hall generator. The Hall generator is connected to the input of the current amplifier, which drives the coil. The current through the coil produces an opposing field to that provided by the current through the aperture Thus the flux in the core is constantly driven to zero. The coil connects the output of the sensor. Therefore the output is a current proportional the aperture current multiplied by the number of turns on the coil. A sensor with a 1000 turn coil provides an output of 1mA per ampere. The current output is converted to a voltage by connecting a resistor to the output of the sensor and ground. The output of the sensor and ground. The output is scaled by selecting the resistor value. Closed loop sensors measure dc and ac currents and provide electrical isolation. They offer fast response, high linearity and low temperature drift. The current output of the closed loop sensor is relatively immune to electrical noise. They are the sensor of choice when high accuracy is essential.
|
|
|
