|
|
Model:
50T(low pressure) + VQ15(high pressure vane pump)
150T(low pressure) + VQ15(high pressure vane pump)
50T(low pressure) + PA(high pressure gear pump)
150T(low pressure) + PA(high pressure gear ppump)
This model design for customer's special application.
Please visit our web site: www.kcl.com.tw
|
|
Qtwo Two Stage Pump
Powerful two stage midship split drive line pump can exceed 2000 NFPA rating and may exceed up to 2600 GPM from a sufficient water source or in relay mode.
Ideal for the following applications:
* Pumper
* Aerial
* Tanker
* Rescue Pumper
* Pumper Tanker
|
|
With its new PRO high-pressure range, KMT Waterjet Systems sets new standards in the field of waterjet cutting. PRO stands for waterjet cutting technology with operating pressures of up to 6200 bar. The new range of products includes of course all necessary components and accessories - from high-pressure generation units to orifices that guide the cutting jet with great precision onto the material. The maximum pressure of 6200 bar represents an increase of nearly 50% over pressures used in conventional equipment!
The advantages offered by this leap in technology are obvious:
- Higher cutting speeds
- Improved cutting edge quality
- Lower abrasive consumption
|
|
The quality, expertise and experience to deliver to your precise requirements.
Hydrokraft piston pumps and motors are renowned worldwide for their robustness and reliability. Hydrokraft offers a complete range of open and closed circuit pumps and motors available in fixed and variable inline design from 66 - 750 cm3 per revolution. Larger displacements can be achieved using combinations of our pumps and motors.
Hydrokraft manufactures high-pressure axial piston hydraulic pumps, motors and transmissions for applications in stationary industrial equipment, marine, mining, chemical processing, primary metals and other markets in open circuit or closed circuit applications.
|
|
Features:
Volumetric efficiency is over 95% and overall efficiency is more than 90% at
1800 r/min.
High performance at maximum pressure 35MPa
A3H series are compact in size becauseoutput / mass ratio is large.
|
|
Adopting a process of continual product development has resulted in todays K3V series of axial piston pumps.
Features such as high efficiency , high power density, large self priming capability, long life, low noise and a wide range of control options has shown the K3VG to be a market leader.
The K3VG unit has been developed specifically for the industrial market where noise, efficiency, controllability, extended pump life and reliability are considered essential.
|
|
The present K3V is designed specifically for the earth moving and construction industries where in excess of 700,000 units have been supplied.
Features such as high efficiency , high power density, large self priming capability, long life, low noise and a wide range of control options has enabled the K3V to be a clear market leader.
Adopting a process of continual product development has resulted in todays K3V series of axial piston pumps.
|
|
Axial piston units are available in the form of pumps and motors in bent axis design or swashplate design for medium- and high-pressure ranges. They are the main components in the hydrostatic transmission. Compact size and high power density, economy and reliability are characteristic advantages which speak for the use of hydrostatic transmissions, together with the fact that they meet the demand for high speed and high torque, as well as optimum efficiency.
|
|
DVQ-25 DURABLE DESIGNED HIGH PRESSURE PUMP
The maximum pressue:250 bar
Displacement:18/22/26/32/38/43/47/52/52/60/65/75
Aplication:
Shoes making machine, Plastic and rubber molding mahcine,
press brake machine, press shear and steel sheet forming machine.
|
|
|
|
|
|
HS
Grundfos HS end-suction pumps combine compact design, economical cost and simple maintenance to provide high-efficiency performance in a wide variety of applications. And because they include the pump end, motor adaptor and standard NEMA motor, Grundfos end-suction pumps install easily with no baseplates, bearing frames, couplings or guards.
FEATURES
* Ideal for water supply, irrigation, commercial and industrial uses
* Cast iron and brass contruction
* Capacity ranges to 175 GPM and 160 feet of head at up to 7.5 horsepower
* 60 Hz models available in all voltages, with 2 and 4 pole and specified enclosure classes available
* Optional MLE variable-frequency drive motor offers maximum efficiency and energy savings
* Buna-N O-rings as standard with carbon/ceramic shaft seal
APPLICATIONS
The Grundfos HS range of compact horizontal, centrifugal pumps are designed for small domestic and industrial water supply systems.
Applications include
* Liquid transfer
* Transfer and circulation of liquids within light industry and farming.
* Pressure boosting
* Domestic water supply
* Water Fountains
* Cooling systems
* Air-conditioning systems
* Light irrigation
* In addition, the HS is suitable for incorporation in specialized OEM equipment
|
|
Feature:
Max. Pressure:245 kgf/cm2
Max. Speed :1800 RPM Min. Speed: 600 RPM
Application: Hydraulic press machine, fishing boat,
lift truck, plastic injection machine.
For detail product dimensions, performance characterisitics and order code, please visit our web site:www.kcl.com.tw
|
|
Axial piston units are available in the form of pumps and motors in bent axis design or swashplate design for medium- and high-pressure ranges. They are the main components in the hydrostatic transmission. Compact size and high power density, economy and reliability are characteristic advantages which speak for the use of hydrostatic transmissions, together with the fact that they meet the demand for high speed and high torque, as well as optimum efficiency.
|
|
| ... products without technical information |
| |
|
|
|
|
Heavy duty process multistage pumps, axially split, diffuser type with single or double entry 1st stage impeller.
Pump components geometry optimised through hydraulic, structural, thermal and dynamic F.E.M. analysis lead to an high product reliability. The "modular design" philosophy permits to cover a wide range of applications replacing the main hydraulic components i.e. only impeller/diffuser. Casing, shaft, mechanical seals, bearing frames result therefore fully interchangeable and reusable. Opposed impeller and diffuser configuration to minimise axial and radial hydraulic thrusts.
Large eye single suction or double suction 1st stage impeller to meet low NPSH requirements.
Hydraulic performances checked on a Single Stage Test Equipment. This is particularly useful to verify the effective 1st stage NPSH.
Easy internal inspectability and maintenance.
Central and lateral balancing drums adequately shaped to optimise pump rotordynamic behaviour.
Near centerline casing mounting for high temperature stability.
Deep stuffing boxes, designed in accordance to API 682 Std., suitable to accept any type of mechanical or packing seals.
Axial split bearing housing for easy inspection and maintenance procedure.
Labyrinths and deflectors at either bearing housing to maximise protection against dirt.
A wide range of sizes and material combinations complete the variety of the offered product.
Main design features
Fully designed according to latest edition of API 610 Std.
Number of stages rangeable from 4 to 13.
Rotor operates away it's critical speeds.
Side-Side suction and discharge nozzles integrally cast on lower casing half.
Contoured grafoil or glassfiber gasket to assure joint between casing halves and eliminate interstage leakages.
A wide range of sizes, number of stages and material combinations complete the variety of the offered product.
Casing guidekeys for high temperature application; over 120°C (250°F).
'CARB' or hydrodynamic line bearing for high temperature application.Three bearings arrangements available:
Ball Radial / Ball Thrust
Sleeve Radial / Ball Thrust
|
|
KT6C SELECTED highest pressure and utmost RPM vane pump
Intensive pressure:350bar
Continuous pressure:275 bar
Maximum RPM:3000RPM
Displacement:21.3/26.4/34.1/37.1/46/58.3/63.8/70.3/79.3/88.8/100
Application:
Ocean going and Marine equipment, construction equipmnet
Scrap balers equipment, Construciton equipment, oil explortion
machine, Oil exploration equipment, presses and shearing machines
* Installation dimensions compatable with Dension pump
|
|
Corken SC-Series pumps are a rotary side channel design. They produce a maximum differential head of 1,150 ft (350 m). The side channel pump is offered in six different sizes, each ranging from one to eight stages. This provides for a wide range of pressures and capacities ranging from 1gpm to 185 gpm (3.8–700 L/min). These pumps can handle discharge pressures up to 580 psig (40 bar).
Product Features
* Radial vane impellers and two outlet openings per stage allow for high vapor content
* Enclosed centrifugal impeller at pump suction provides improved NPSH capabilities
* Exceptional in light liquid and liquefied gas transfer
* Floating Impeller - No metal to metal contact.
* Modular design
* Smooth continuous flow
|
|
DVQ-20 low noise, excellent performance high pressure pump
The maximum pressure can reach 270 bar
Displacements: 17, 23, 26, 32, 38,44
Apply to:hydraulic press brake, shear, bending and steel sheet forming machine.
* Installation dimensions compatable with Atols pump
|
|
Feature:
Max. Pressure:245 kgf/cm2
Max. Speed :1800 RPM Min. Speed: 600 RPM
Application: Hydraulic press machine, fishing boat,
lift truck, plastic injection machine.
For detail product dimensions, performance characterisitics and order code, please visit our web site:www.kcl.com.tw
|
|
| ... products without technical information |
| |
When you need to produce and control high pressures, forces and torques permanently for mobile applications, then there are some pre-conditions:
- robust, service-friendly technology
- small size
- low weight
- as flexible multiple use of a component as possible
- easy handling and operation
The KRACHT mobile hydraulic components meet these requirements exemplarily. A glance at the technical data will convince you.
|
|
KF gear pumps are used for pumping a wide variety of
fluids.
KF gear pumps are distinguished especially by their wide
range of variants which are assembled as required on the
modular principle and also permit subsequent upgrade.
The pumps are also suitable for media with low lubricating
properties.
The standard housing sections are of grey cast iron.
The gear units are manufactured from high-strength
case-hardening steel, hardened and mounted in special
multi-compound plain bearing bushes.
The standard drive shaft is sealed by rotary shaft
lip-type seal.
All pump sizes incorporate helical tooth system.
This feature, combined with special gear geometry,
results in extremely low noise levels and reduced
pressure pulsation.
|
|
When you need to produce and control high pressures, forces and torques permanently for mobile applications, then there are some pre-conditions:
- robust, service-friendly technology
- small size
- low weight
- as flexible multiple use of a component as possible
- easy handling and operation
The KRACHT mobile hydraulic components meet these requirements exemplarily. A glance at the technical data will convince you.
|
|
|
|
|
|
Rugged, durable, and built to perform. All things that Haight is pleased to say the large flow pumps can provide. Built for some of the most challenging applications including: chemical use, fuel transfer, oil filtration, lubrication systems, and more. With pump sizes ranging from 120-240 gpm, which compliments our existing line of 1-80 gpm, and multiple seal configurations - you can be sure Haight can provide a pump that will work for your application.
Some of the key features in these DIU Series pumps are: ductile iron housings, steel shaft and pinion gears, and iron rotor with multiple bearing materials. Shaft sealing will include packing seals, lips seals & multiple mechanical seal types, with elastomers to suit. Other features and options are available depending on
Specific needs and applications.
Other features include:
- Built in Shaft Seal Flexibility
- Reduced maintenance and wear due to less moving parts
- Close Coupled design eliminates mis-alignment and related failures
- “Gear within a Gear” design for quiet operation
- Direct Drive - speeds to 1800 RPM
- Relief valve
- Wear Sleeves
Haight Pump is pleased to offer over 75 years of pump design, manufacturing knowledge and experience. Our ability to provide the customer with reliable pumps, quality customer service, quick reaction time, and in house capabilities (Manufacturing, Engineering, etc) makes us a quality supplier in the pump industry.
|
|
|
Liquiflo Max-Series Gear Pumps are manufactured from 316 Stainless Steel or Titanium, and are available in both Sealed and Mag-drive configurations. These pumps feature Helical gears and relieved wear plates for smoother and quieter operation and intrinsic reduction of gear separation forces. Their unique and durable design will assure extended life in high-pressure pumping applications.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
