|
|
The axial piston fixed pump AHP PF - 20 is designed for various applications in open hydraulic circuits. At the figure No. 2 is drawn cross sectional view of the piston pump.
The shaft is supported by two tapered roller bearing. Design of the end of input shaft you can find on the page 16 of this catalogue. Hydraulic pump is closed by the front and rear cover. The rear cover also serves for connection of the high-pressure and suction ports. The angle of the swash plate is fixed on 18°.
Fig. 2: Cross sectional view of fixed pump.
Flange with centering diameter according to the standard SAE is bolted to the front cover. Tightness of the case around the exiting part of the shaft is protected by the shaft seal for max. pressure 0,25 MPa (intermittent 0,5 MPa).
|
|
|
|
|
|
PVK units are axial piston pumps of slipper design. Rotor of this pump is driven by shaft which is supported by 2 roller bearings. Inside of the rotor, there are moving 9, hydrostatically balanced, pistons parallel with an axis of rotation. They are slipping on the inclined thrust plate which is placed inside of the swash plate and this way, the pistons are moving with a straight-line motion.
They create 1 suction and 1 pressure stroke per revolution. Fluid direction is performed by frontal rotational distribution. Single cylinders are joined either with a suction channel or a pressure one of the end cap during a motion of the distributor. Swash plate angle is possible to regulate continuously with various ways of control and automatic regulations (mentioned in 5, 5.1 and 9.1) which are part of axial piston pump.
These units are designed for conversion of mechanical energy into pressure one. They can be used in closed loops of various machines (e.g. road, construction, grading, agricultural, forest, mining etc.) where is demanded a continuous change of input parameters. The loop has to be designed such way that pump parameters, which are determined by technical conditions and project of the specific application , must not be exceeded during an operation.
|
|
Variable displacement axial piston pumps of swash plate design series AHP-10 are designed for various applications working in closed hydrostatic circuit.
Fluid flow is in proportional relation with speed and displacement of pump, which can be increased with changes of swash plate angle from zero to maximum. Standard pump is equipped with internal charge pump - G-rotor type, manifold assembly with block of flushing and two pressure relief valves on the high pressure ports.
Relief valves protect the hydrostatic transmission from overloads. Standard pump is equipped with mechanical - hydraulic servo valve with mechanical feedback. Tightness of the case around the exiting part of the shaft is protected by the shaft seal for max. pressure 0,25 MPa (intermittent 0,5 MPa).
|
|
Variable displacement axial piston pumps of swash plate design series AHP-20 are designed for various applications in open hydrostatic circuit.
Fluid flow is in proportional relation with speed and displacement of pump, which can be increased with changes of swash plate angle from zero to maximum.
Standard pump is equipped with internal charge pump of gerotor type, manifold assembly with block of flushing and two pressure relief valves on the high-pressure ports.
Relief valves protect the hydrostatic transmission from overloads. Standard pump is also equipped with mechanical - hydraulic servo valve with mechanical feedback. Tightness of the case around the exiting part of the shaft is protected by the shaft seal for max. pressure 0,25 MPa (intermittent 0,5 MPa).
|
|
The InLine variable displacement pump type V30D and V30E work according to the swash plate principle and are intended for open circuit operation in industrial and mobile hydraulics. There is also an option for a thru-shaft for flange mounting additional variable and fixed displacement pumps. Type V30E is intended as successor of V30D, where the completely new development allowed to realize state of the art pump design. This concerns primarily the optimization of self-suction speed rating, minimized noise level, weight, and pulsation as well as increased service life.
These pumps are suited for a wide range of applications due to their low running noise and various pump controllers.
Hydraulic circuits where several outlet flows are required can be fed either by one individual pump or a multiple pump. Main benefit of these pumps are the sturdy design, the good performance/weight ratio, long service life
due to oversized bearings, and the swash plate angle indicator.
|
|
The T1-51, -81, -121 fixed displacement pump has been specifically developed to meet the requirements of light duty truck applications with short, non-frequently operating cycles such as tippers and small loaders.
Input power up to 71 kW
Shaft speed up to 2300 rpm
Operating pressure up to 350 bar
High overall efficiency
Low weight
Small intalled envelope
Proven reliability
Easy servicing
|
|
Atos PVPC pumps are variable displacement axial piston pumps for high pressure operation on industrial applications at low noise level
• 4 basic models up to 100 cm3/rev
• pressure up to 280/350 bar
• full line of electrohydraulic servocontrols, by analog or digital electronics
- vane pumps, fixed displacement, cartridge design, with integral hydraulic balancing, low noise level
|
|
|
|
|
|
The SP700 and VP700 are new battery powered backpack units weighing no more than 18KG providing hydraulic power for cutting tools, and other hydraulic equipment such as Jaws of Life® and hydraulic jacks as used by emergency services and in many other situations.
Jon Lye, Managing Director of GSF explains: “The uniqueness of the Interfron range definitely improves emergency operations; it’s an innovation in design and one we believe will make a dramatic difference to the industry.”
Indeed the range of battery powered backpacks are unique in the respect that it gives emergency crews complete freedom from petrol driven or vehicle mounted power supplies; no hydraulic extensions and no attachments mean no entanglements, which, in low visibility high risk environments, reduce accidents and increase access to enclosed and otherwise inaccessible spaces.
At the heart of the range is the SP700 and the VP700, both of which can be fitted with the appropriate hydraulic connectors, enabling the units to operate rescue tools from all major manufacturers, including: Holmatro, Amkus, Lukas, Zumro, Weber, TNT, Lancier, Nike Centaur, ResOtec and Enerpac. The units can be adjusted to use hydraulic pressure at 5100, 9200 and 10500 psi. Each unit has a total weight (approx) 18kg (40lbs).
This Interfron range represents a very exciting addition to GSF’s long established market leadership on high strength shock resistant telescopic slides, and our state of the art Promounts range of mounting gear, used to secure every type of gear and equipment onto emergency and defence vehicles.
- Jaws of Life® is a registered trademark of Hale Products, Inc.
|
|
|
|
|
|
M Series pumps are open circuit, axial piston designs. A variety of controls provides the ability to match the pumps to each application.
A strong, proven rotating group allows the pumps to handle pressures to 280 bar (4000 psi) continuous and 320 bar (4600 psi) intermittent - with less maintenance cost. Each frame can also contain a 230 bar (3300 psi) higher flow rotating group that provides additional application flexibility. High-load bearings and a stiff drive shaft help provide a pump life of 30,000 hours (@ 65% rated pressure), reducing operating costs and extending machine life.
M Series pumps feature a saddle-type yoke with steel-backed polymer bearings. The stiff yoke reduces deflection and allows even loading of bearings, improving life. A single control piston reduces loading on the yoke, resulting in reduced pump size that allows installation in tighter locations.
M Series pumps operate at a level of quietness that exceeds the requirements of today's demanding industrial conditions. The pumps feature a unique three-piece envelope (flange, housing and valve block) specifically created for low fluid-borne and structureborne noise levels. Another pump feature - a bimetal timing plate - improves pump filling characteristics that, in turn, reduces fluid-borne noise and extends pump life.
|
|
Fixed displacement bent axis piston pumps.
STRADA pumps are ideally suited for PTOs applications in vehicles.
Displacements from 2.49 in³/rev (40,9 cm³/rev) to 6.71 in³/rev (110 cm³/rev) available in groups 32 and 37.
Max. peak pressure up to 5800 psi (400 bar)
Max. speed up to 2950 min-1
|
|
The quality, expertise and experience to deliver to your precise requirements.
Hydrokraft piston pumps and motors are renowned worldwide for their robustness and reliability. Hydrokraft offers a complete range of open and closed circuit pumps and motors available in fixed and variable inline design from 66 - 750 cm3 per revolution. Larger displacements can be achieved using combinations of our pumps and motors.
Hydrokraft manufactures high-pressure axial piston hydraulic pumps, motors and transmissions for applications in stationary industrial equipment, marine, mining, chemical processing, primary metals and other markets in open circuit or closed circuit applications.
|
|
Features:
Volumetric efficiency is over 95% and overall efficiency is more than 90% at
1800 r/min.
High performance at maximum pressure 35MPa
A3H series are compact in size becauseoutput / mass ratio is large.
|
|
Our piston pumps is delivers high efficiency and low mantenance under the toughest operating conditions.
* Reliable fast response mechanism
* Special shaped fluid port reduces nosie
* High strength cast iron housing
* Designed to handle a various application.
For more model, specs. dimensions, please viist our
web site:www.kcl.com.tw
|
|
SUNFAB SL
Dual-flow pump with displacement from 20/20 to 53/53.
also some differentiated flows.
Perfect for demanding hydraulic mobile applications, up to 330-350 Bar.
|
|
GEHO DHT
This GEHO DHT pump is an industrial design hydraulically driven piston pump capable of handling extremly viscous slurries, sludge and paste, both organic and mineral, on a 24/7 operational basis. These pumps have excellent suction capabilities, are designed to handle large objects and to minimize wear. The DHT pump range is developed and manufactured by Weir Minerals Netherlands b.v.
Features / Benefits
- capacities up to 100 m3/h
- pressures up to 120 bar
- high viscosities up to 100.000 cP (mPas)
- moderate to high abrasiveness
- mild corrosiveness
- up to 120 mm particle size
- up to 90% solids content
|
|
Features
High efficiency
Under the conditions of pressure 16 MPa (2320 PSI) and speed 1800 r/min, the volumetric efficiency is over 98% and the overall efficiency is over 90%.
Low noise level
In the "A16" pump, the noise level is as low as 57.3 dB(A) [at the full cut-off pressure 21 MPa (3050 PSI) with speed 1500 r/min one metre (3.3 ft.) horizontally away from pump head cover.]
|
|
SC 75/75
Dual-flow pump for truck hydraulics with need of big flows, for example forestry applications.
The Compact Line is suited for demanding applications with its high torque, high pressure, high efficiency, low noise level
and very small dimensions
|
|
Variable displacement axial piston pumps swash plate design.
PLATA pumps are ideally suited for medium and high pressure open circuit applications
Displacements from 1.74 in³/rev (28,49 cm³/rev) to 5.37 in³/rev (87,9 cm³/rev)
Max. peak pressure up to 5075 psi (350 bar)
Max. speed up to 3000 min-1
|
|
|
These AR series pumps heve been developed on the basis of the same design concept as A series pumps which are renowned for high efficency and low noise level. Using an alminum body, the size of the pump is more compact and the mass is considerably reduced. The noise level has also been reduced.
|
|
Adopting a process of continual product development has resulted in todays K3V series of axial piston pumps.
Features such as high efficiency , high power density, large self priming capability, long life, low noise and a wide range of control options has shown the K3VG to be a market leader.
The K3VG unit has been developed specifically for the industrial market where noise, efficiency, controllability, extended pump life and reliability are considered essential.
|
|
The present K3V is designed specifically for the earth moving and construction industries where in excess of 700,000 units have been supplied.
Features such as high efficiency , high power density, large self priming capability, long life, low noise and a wide range of control options has enabled the K3V to be a clear market leader.
Adopting a process of continual product development has resulted in todays K3V series of axial piston pumps.
|
|
The latest design in the proven K3V series, the medium pressure, K3VL pump has been developed for the mobile and industrial market where noise, efficiency, controllability, extended pump life and reliability are all considered essential.
Pioneering noise reduction technology along with features such as high efficiency, compact design, high power density, large self priming capability, long life, and a wide range of control options give rise to exceptional overall specification and performance.
Available in SAE and ISO mounting options, this low noise, medium pressure, variable displacement, open circuit pump provides the opportunity to share in the future of hydraulic pump technology.
|
|
|
|
|
|
Features/performances
The pump is available in faces 71,100 and 140 DC.
Sizes 28,45 and 180 DC will be marketing soon.
Pressure rating = 280 bar
Intermittent Pmax = 350 bar
Hydromechanical regulations: pressure, flow, power. See A10VSO 32 according to note RF92714
Electronic regulations:
SYDFE1-3X: analogical order via off-set amplifier,
SYDFEE-3X: analogical order via integrated amplifier,
SYDFEC-3X: order by CANopen via integrated amplifier
Description and Applications
A10VSO is an axial-piston pump of variable cubic capacity for industrial applications on average pressure. It showed its reliability in the plastic machine, the machine tool, the paper mill, or the agroalimentary one
Series 32 brings the following innovations:
Improvement of the ambient noise (- 3dB) and reduction of the pulsations by room of precompression
Improvement of the total output (+3%)
Improvement of the reliability of the rotary group and the hydraulic regulators
Improvement of its flexibility for the combinations of pumps: catch of universal force, standard ISO and SAE
Series 32 preserves the possibilities of operation with the not easily flammable fluids.
For the applications to high dynamic response and with a view to energy saving, series 32 also proposes a hydraulic electro order in loop closed under name SYDFE (X) - 3X.
|
|
Variable-displacement axial piston pumps for closed circuits
Variable displacement axial piston pumps for open circuits
Fixed displacement axial piston motors
Variable displacement axial piston motors
|
|
|
Complete range of variable displacement axial piston pumps, with swashplate system, for closed loop transmissions. All pumps meet the need for continuously changing speeds, optimise the use of power and torque based on operating requirements, with hydraulic, mechanical, electric and electronic servo controls.
|
|
|
Axial piston pumps with fixed displacement have been development to work in light trucks with shorts periods of time. Its design is very similar to F1 series.
|
|
|
|
|
|
Axial piston units are available in the form of pumps and motors in bent axis design or swashplate design for medium- and high-pressure ranges. They are the main components in the hydrostatic transmission. Compact size and high power density, economy and reliability are characteristic advantages which speak for the use of hydrostatic transmissions, together with the fact that they meet the demand for high speed and high torque, as well as optimum efficiency.
Characteristics:
- Open and/or closed circuit
- Displacement 5 to 1000 cm3
- Nominal pressure up to 450 bar
- Maximum speed up to 11,000 rpm
- Maximum power output 933 kW
Our versatile transmissions for mobile applications can be combined in a variety of ways with pumps, motors and open or closed loop control devices to offer the optimum design for every drive application and every power range.
Key advantages:
- Infinitely variable speed setting at fixed or variable input speed
- Immediate, jolt-free change in direction of rotation
- Simple, ergonomic operation
- High turnaround
- Automatic torque conversion
Axial piston pumps and motors are used for the travel drive and working hydraulics in a wide variety of mobile machines.
|
|
|
DESCRIPTION Oil hydraulic bent pump, 108cc/rot, aplication pressure-up to 350bar, peak pressure-400bar
|
|
Axial piston units are available in the form of pumps and motors in bent axis design or swashplate design for medium- and high-pressure ranges. They are the main components in the hydrostatic transmission. Compact size and high power density, economy and reliability are characteristic advantages which speak for the use of hydrostatic transmissions, together with the fact that they meet the demand for high speed and high torque, as well as optimum efficiency.
|
|
- For agricultural and truck applications
- Axial. From 20 c.c./rev to 110 c.c./rev
- Radial. From 11 c.c./rev to 96 c.c./rev
- Pressure up to 350 bar
|
|
|
|
