|
|
|
|
|
|
Addi-Data presents the new 32-bit digital input/output board PC104-PLUS1500 which has 32 I/O. The PC104-PLUS1500 is equipped with both PCI and ISA connectors on the circuit board. The direct connection to SPS controls is guaranteed because the I/O channels correspond to the industrial standard +24 V for “logic 1”. The input voltage is designed precisely so that the PC104-PLUS1500 switches reliably to „0“ or „1“, even in the case of disturbances. With 0-14 V as “low” and 19-30 V as “high” the ranges are set very high. In order to ensure that the board is interference-free and thus the flawless use in applications, the 32 digital inputs/outputs are isolated up to 1000 V and protected against fast transients, electrostatic discharge and high-frequency EMI.
Two digital inputs are interruptible and thus the main programs are relieved of the standard monitoring and evaluation tasks. In order to avoid undefined states the outputs stay on “status 0” when the PC is started.
The High-Side switch outputs that are available on the PC104-PLUS1500 are designed for inductive loads and PTC resistors, in contrast to the open collector outputs. They work with a nominal voltage of 24 V and an output current of 150 mA and are protected against short-circuit, overtemperature and undervoltage. Additionally, 3 timers or counters are available, whereas Timer1 can work as programmable watchdog for resetting the outputs. A status register that can be read out allows to detect short-circuit or overtemperature.
|
|
Product Range:
AIM104-IN16 16 opto-isolated inputs
AIM104-IO32 32 TTL compatible digital I/O
AIM104-RELAY8-IN8 8 changeover relays and 8 opto-isolated inputs
AIM104-OUT16 16 opto-isolated Darlington driver outputs
AIM104-OPTO-IN8/OUT8 8 opto-isolated inputs and 8 opto-isolated outputs
AIM104-ADC16/IN8 Isolated 16 channel 12 bit ADC and 8 channel digital input
AIM104-MULTI-IO Isolated 16 channel 12-bit ADC, 2 channel 12 DAC and 8 channel digital input
AIM104-MOTION-1 8-bit PC/104 module providing single axis stepper / DC servo motor control with on-board drivers
AIM104-MULTI-IO Isolated 16 channel 12-bit ADC, 2 channel 12 DAC and 8 channel digital input
CTR-1462 Galvanically isolated DIO, 24 inputs and 24 outputs
DAQ-1278 Cardbus controller with 1 x 32-bit slot for type I, II and III card support
|
|
Micronix PC/104 boards is European manufactured expansion modules for the PC/104 bus, designed for industrial and process control systems and for automotive applications.
|
|
Analog Input & I/O
12-bit or less resolution
14 and 16 bit resolution
Analog Output
12-bit or less resolution
Digital I/O
Counter-Timer
Parallel
Special purpose
Serial Communications
LPT Port and 2
|
|
| ... products without technical information |
| |
|
|
|
|
* 14 bit transient recorder
* One channel with 400 MS/s
* Monolithic A/D converter (no interlace)
* Two channels with 250 MS/s
* High dynamic range
* Up to 2 GSample memory
* 6 input ranges between ±100 mV and ±5 V
* 50 Ohm/1 MOhm, AC/DC, bandwidth filter software selectable
* Automatic on-board calibration
* Synchronisation to multi-board system possible
* 32 Bit 66 MHz PCI/PCI-X interface available
* PCI Express x1 Interface available
The 6 models of the M3i.41xx series are designed for the fast and high quality data acquisition. Each of the input channels has its own monolithic A/D converter and its own programmable input amplifier. This allows to record signals simultaneously on both channels with 14 bit resolution without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates. All boards of the M3i.41xx series may use the whole installed on-board memory for the currently activated number of channels. A FIFO mode is also integrated on the board. This allows the acquisition of data continuously for online processing or for data storage to hard disk.
|
|
|
|
|
|
* 14 bit A/D + 16 bit digital with 50 MS/s
* Optimized for RADAR applications
* acquisition of azimuth and elevation angle
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* Up to 2 GSample memory
* 6 input ranges between ±200 mV and ±10 V
* Input offset up to ±200%
* Window/pulse width/re-arm/OR/AND trigger
* Automatic offset calibration
* Synchronisation to multi-board system possible
* Synchronous digital channels and ABA mode available as an option
The both cards of the M2i.40x8 series combine fast A/D data acquistion with the feature to acquire digital data in parallel. With this feature it is possible to either acquire 16 digital bit in parallel from one or more angle decoders or acquiring one or two encoder signals directly by using internal counters. Digital data is either stored continuously and synchronously with the analog data or as an angle marker with each data segment (Option Mutliple Recording needed).
Digital data can be either acquired fully in parallel or as a combination of a counter input and parallel digital data. The acquisition
mode can be programmed by software.
When operating in continuous mode the analog and digital data is stored alternating in the on-board memory. For each 14 bit analog sample there is one corresponding 16 bit digital sample.
When operating in segmented marker mode there is one 16 bit digital sample stored at the end of each acquired segment holding the azimuth
and elevation angle for this segment of analog data.
Acquisition can run with full sampling speed independant of the selected mode.
|
|
|
|
|
|
* 12 bit transient recorder
* 2 synchronous channels with seperate A/D
* 100 MS/s on 2 channels
* Up to 256 MSample memory
* 6 input ranges between ±200 mV and ±10 V
* FIFO mode up to 50 MS/s sum samplerate
* Input offset up to ±100%
* Automatic offset calibration
* Synchronisation to multi-board system possible
* 32 Bit CompactPCI 6U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MC.30xx series offer a wide range of very fast 12 bit A/D converter boards for CompactPCI 6U bus. Due to the well-planned design these boards are available in several versions and different speed grades. That makes it possible for the user to find a individual solution.
These boards offer one to four channels with a maximum sam-plerate of 200 MS/s. As an option 4 digital inputs per channel could be recorded synchronously. The installed memory of up to 256 MSample will be used for fast data recording. It can completely be used by the currently active channels. If using slower samplerates the memory is switched to a FIFO buffer and data will be transferred online to the PC memory or to hard disk.
Several boards of the MC.xxxx series may be connected together by the internal standard synchronisation bus to work with the same time base.
|
|
|
|
|
|
* 14 bit transient recorder
* Two channels with 250 MS/s
* High dynamic range
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* Up to 2 GSample memory
* 6 input ranges between ±100 mV and ±5 V
* 50 Ohm/1 MOhm, AC/DC, bandwidth filter software selectable
* Automatic on-board calibration
* Synchronisation to multi-board system possible
The 6 models of the M3i.41xx series are designed for the fast and high quality data acquisition. Each of the input channels has its own monolithic A/D converter and its own programmable input amplifier. This allows to record signals simultaneously on both channels with 14 bit resolution without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates. All boards of the M3i.41xx series may use the whole installed on-board memory for the currently activated number of channels. A FIFO mode is also integrated on the board. This allows the acquisition of data continuously for online processing or for data storage to hard disk.
|
|
|
|
|
|
* High-performance 8 bit transient recorder
* 4 simultanous channels with 100 MS/s
* 2 simultanous channels with 200 MS/s
* Systems up to 64 x 100 MS/s 8 bit A/D available
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* Up to 4 GSample memory
* 7 input ranges between ±50 mV and ±5 V
* Input offset up to ±400%
* Window/pulse width/re-arm/OR/AND trigger
* Automatic offset calibration
* Synchronisation to multi-board system possible
* ABA mode available as an option
The four models of the M2i.20xx series are designed for the fast and high quality data acquisition. Each of the up to four input channels has its own A/D converter and its own programmable input amplifier. This allows to record signals on all channels with 8 bit resolution without any phase delay between them. The inputs can be selected to one of seven input ranges by software and can be programmed to compensate an input offset of ±400% of the input range.
The extremely large on-board memory allows long time recording even with highest sampling rates. A FIFO mode is also integrated on the board. This allows to acquire data continuously for online processing in the PC or for data storage on hard disk.
|
|
16 bits vertical resolution
• 2 or 4 digitizing channels
• 100 or 200 MS/s maximum sampling per channel
• 128 MS to 2 GS on-board acquisition memory
• 65 or 125 MHz bandwidth
• Full-size, single-slot PCI card
• Full-featured front-end, with software control with input ranges, coupling and impedances
• Input ranges between ±100 mV to ±50 V
• 32 bits, 66 MHz PCI standard for 200 MB/s transfer to PC memory
• Ease of integration with External or Reference Clock In and Clock Out, External Trigger In and Trigger Out
• Programming-free operation with GageScope® oscilloscope software
• Software Development Kits available for LabVIEW, MATLAB, C/C# and Linux
The RazorTM family of multi-channel digitizers features up to 4 channels in a single-slot PCI card with up to 200 MS/s sampling per channel, and up to 4 GB of on-board acquisition memory.
Combine several Razor cards for up to 32 channels in a single system.
For Realtime Applications eXpert Options:
• eXpert™ FIR Filtering Firmware Option
|
|
|
|
|
|
Fluke 225C et 215C – ScopeMeter couleur avec test de bus industriels
Les ScopeMeters couleur 225C et 215C offrent toute la palette de fonctionnalités des modèles 199C et 196C. Ils les enrichissent en outre de puissantes capacités de mesure dédiées au contrôle des bus industriels les plus répandus. En mode BusHealth, ces ScopeMeters soumettent automatiquement les signaux électriques véhiculés par le bus à une analyse approfondie. Les paramètres mesurés sont ensuite comparés aux valeurs normalisées prescrites pour le type du bus sous test. L'utilisateur peut aussi sélectionner l'affichage du « diagramme de l'œil » et contrôler visuellement la qualité globale du signal.
Les paramètres mesurés sont automatiquement définis comme « bons », « faibles » ou « mauvais » en fonction des normes correspondantes ou des valeurs de référence définies par l'utilisateur. Chaque paramètre est présenté avec sa valeur actuelle, accompagnée de statistiques MIN-MAX relevées dans le temps. Les valeurs de référence également indiquées aident l'utilisateur à cerner plus aisément le comportement du système. L'appareil mesure notamment l'amplitude des signaux, la tension de polarisation, les temps de montée et de descente, la gigue, la distorsion et les niveaux de bruit (bruit intra-bande et hors bande), selon les spécificités de la norme industrielle concernée.
|
|
|
|
|
|
1 digitizing channels
• 4 GS/s maximum sampling rate
• 8 bits vertical resolution
• 256 MS to 4 GS on-board acquisition memory
• 1.5 GHz bandwidth
• 7.6 bit ENOB
• Full-size, single-slot PCI card
• Full-featured front-end, with software selection of all signal conditioning settings
• 32 bits, 66 MHz PCI standard for 200 MB/s transfer to PC memory
• Ease of integration with Reference Clock In and Clock Out, External Trigger In and Trigger Event Out
• Programming-free operation with GageScope® oscilloscope software
• Software Development Kits available for LabVIEW, MATLAB, C/C# and more
The CobraMax CompuScope family of GaGe ultra high-speed 8-bit digitizers provides the most powerful combination of speed, memory, and bandwidth as well as a wide portfolio of advanced acquisition features.
The GaGe CobraMaxTM family of digitizers features up to 2 channels in a single-slot PCI card with up to 4 GS/s sampling per channel, and up to 4 GB of on-board acquisition memory. Combine several CobraMax cards for up to 16 simultaneous channels in a single system.
|
|
PicoScope handheld oscilloscopes convert your laptop or desktop PC into a powerful oscilloscope, spectrum analyzer and meter without the need for additional probes or power supplies.
The PicoScope 2104 and 2105 are portable handheld oscilloscopes that are ideally suited for use by hobbyists, students, technicians, and anyone looking for an easy-to-use, affordable, single-channel PC oscilloscope.
The small size of PicoScope handheld oscilloscopes makes them ideal for portable use, while still including the powerful features normally found in larger oscilloscopes.
* Ergonomically designed to fit in the hand
* Up to 100 MS/s real-time sample rate
* Up to 2 GS/s repetitive signal sample rate
* Up to 25 MHz bandwidth
* Up to 24,000 sample buffer memory
* Connected and powered by USB
|
|
Looking for something to replace that bulky benchtop oscilloscope?
A high-performance PC Oscilloscope from the PicoScope 5000 Series is your ideal choice.
As well as a 2-channel USB Oscilloscope, the PicoScope 5000 Series can also be used for high-speed data acquisition and includes an arbitrary waveform generator that can generate a waveform of almost any shape.
Other oscilloscopes at this price range force you to compromise on either bandwidth, sampling rate or buffer memory. With class-leading bandwidth, sampling rate and memory depth, and an array of advanced high end features, PicoScope 5000 PC Oscilloscopes give you the features and performance you need without compromise.
When performance is paramount, a PicoScope 5000 high-performance oscilloscope meets your needs.
* 250 MHz bandwidth
* 1 GS/s real-time sample rate
* 128 Megasample buffer memory
* Arbitrary waveform generator
|
|
| ... products without technical information |
| |
|
|
|
|
Main Applications
- Point of Sale
- Retail
- Hospitality
- Airlines
- Postal Services
- Car Rentals
Features
- PC/SC and EMV 2000 Compatible Smart Card Reader Ensures Universal Application Support
- Top Insertion Smart Card Reader Enables Card to Stay in Plain View of the User
- Supports Maximum Smart Card Speed for Fastest Data Transmission and Highest Read & Write Performance
- Landing Contacts Ensure up to 200,000 Smart Card Insertion Cycles
- Smart Card Reader Drivers for Windows, Linux and Macintosh
- 43 Free Programmable Keys for Easy Layout Configuration
- High Performance Magnetic Stripe Reader with Freely Programmable Headers and Terminators for Each Track
- Selection of Non-Keyboard Hexcodes Enhances Security for Credit Card Processing
- Free Parsing and Configuration of Magnetic Stripe Data
- Powerful Configuration Software 'Cherry Tools' Enhances Functionalities When Switching into 'Virtual Programming Mode' and Allows for Quick Product Setup & Configuration
- Easy Configuration File Transfer with Windows Explorer
- UPOS Drivers for Windows and Linux Support of Client-Server Architectures
- Remote Network Installation with 'Cherry Tools' Runtime Version (USB)
- Compact 16" Footprint
- Mechanical Keyswitches are Rated at 50 Million Actuations to Withstand Harsh Environments and Ensure Long Product Lifetime
- Full US 104 Position Key Layout
|
|
Intrinsically safe PC keyboards for use in hazardous areas
The PC-compatible Exi keyboards in the TASTEX product series are designed for use in hazardous areas (Zones 1, 2 and 22) and comply with the IP 65 degree of protection. Variants without a mouse (EXTA-K1), with an integrated trackball (EXTA-K3) or with an integrated touchpad (EXTA-K4) can be supplied.
|
|
Q-board
Benefits
Compact size, more desk space
Less reaching for operating the mouse
Conventional keys
Comfortable and efficient in use
Integrated numeric pad
Conveniently positioned arrow keys
10 Office Hot Keys for frequently used functions
Specifications
Connection:
PS/2 and USB in one
Keyboard layout:
US/ EUR (different layouts on request available)
85 (Windows layout, conventional)
10 (Office Hot Keys)
Cable length:
140 cm
Standards:
NEN-ISO 9241-4, FCC, and CE
Dimensions:
wxdxh: 336 x 165 x 32 mm
Weight:
690 g
|
|
|
The Nd-M15-KB and Nd-M17-KB units are rugged, fully integrated 15.1" and 17" color LCD drawer monitors with keyboard and PS/2 mouse pad designed to fit in 19" rack mount chassis. When fully stowed, the system measures a mere 1.75" (1U) in height. The large 15.1" and 17" color flat panel LCD displays feature resolutions of 1024x768 and 1280x1024 respectively, while achieving true color graphics. Interfacing to the computer is easy with the supplied cables for keyboard, video and mouse. Its rugged, slim design makes this unit ideal for industrial and telecommunications applications.
|
|
| ... products without technical information |
| |
... see all the products in the category
Keyboards
|
High-pressure hoses or hose assemblies have to be tested before delivery. The requirements are going further then only pressure testing. More often end users ask suppliers for more specific characteristics of hoses.
Resato hose testing machines are delivered to end users in a production environment as well as hose distributors and hose testing laboratories. The Resato machine will give you a certificate which is your quality release document.
Examples of applications in the hose tes
Hydraulic pressure testing.
Gas pressure testing.
Burst pressure testing.
Length, rotation and expansion measurements during pressurization.
WE ARE LOOKING FOR A DISTRIBUTOR IN ITALY. Please contact us if you are interested!
|
|
| ... products without technical information |
| |
|
|
|
|
Mecmesin offer a range of sophisticated Computer-controlled Test Frames. The Multi-test-i is available in a range of capacities to accommodate all your testing requirements, from the entry level MultiTest 1-i through to the advanced twin column test frames that have been specifically designed to test large or high load samples or products.
Intelligent loadcells mounted to the test frame allow the MultiTest-i to download data directly to a PC via the serial port at a rate of 2000 times a second. If your test requirements change then the MultiTest-i can easily be upgraded with a different load cell that meet your new testing requirements.
Emperor, Mecmesin’s powerful yet user-friendly control software, provides both a simple platform for routine analyses on the factory floor, as well as an advanced platform for sophisticated laboratory test routines. Programmable functions include running a test to a pre-determined force/torque, displacement, time or to break, as well as graphical interrogation of results.
Applications
The MultiTest-i range of motorised test stands can be used for many different applications including:-
Compressive testing
Deformation testing
Extension testing
Materials testing
Medical device testing
Packaging testing
Spring testing
Tensile testing
Textile testing
Top-load testing
Mecmesin offer a wide range of standard grips and fixtures, to hold your specimen. Alternatively, a custom-built fixture can be designed for your specific application.
|
|
Liebert XD™ System
Liebert energy-efficient and flexible high heat density cooling solutions are available with Open or Closed architecture and Pumped Refrigerant-based or Water-based technology.
Liebert XD refrigerant-based cooling modules work as a system to support the hot aisle/cold aisle approach to cooling high heat density data centers. The modules provide focused rack cooling, enhancing a room precision cooling unit, such as a Liebert DS system. Pumped refrigerant is ideal for use around electronic equipment, operating at low pressure in the piping circuit, and becoming a gas at room conditions.
|
|
|
|
see the results for the following category : 
