|
|
Flexible I/O for SCADA, Sequential Event Reporting, and Station Integration. Add up to 37 inputs and outputs to an SEL-2032 system. The base unit includes three digital outputs and two digital inputs. Use each of four card positions for one of the following I/O cards: eight analog inputs for dc process values (One card maximum), eight digital inputs to sense status of contacts, eight digital outputs to control external devices. Time-Tagged Sequential Events Recorder (SER). Store up to 512 SER reports of digital input transitions, time-tagged to the nearest millisecond. Send the SER data to a communications processor for system analysis and troubleshooting.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
... see all the products in the category
Keyboards
|
This digital, modular sensor with PMU Plug-and-Measure unit measures the relative humidity and temperature and calculates to output the values of the dew point temperature, water content, enthalpy, absolute humidity and wet bulb temperature.
|
|
The FEM diaphragm dosing pump has been specially developed
in order to accurately dose small quantities of liquid over a long
period of time whereby two of its most distinctive features are its
compact size and robustness (pump and electronics). The FEM
pump and electronics makes a complete dosing system which
is suitable for both simple as well as complex applications. With
the functions „quasi continuous flow“ and „batch dispensing“ the
FEM diaphragm pump differentiates itself from pumps based on
alternative technologies eg. piston, gear, syringe and peristaltic
pumps. Other interesting features are its high reliability, a
favourable purchasing price and low maintenance costs.
KNF has developed a specially programmed electronic control
module so that the integrated solenoid valve and the movements
of the diaphragm are exactly synchronised. This results in an
exact dosing which is gentle and low in pulsation. In addition
to these unique pump characteristics the control module also
allows a wide range of control possibilities to be used eg.
serial interfaces.
The dosing pump is self priming, maintenance free and can
be run dry |
|
The FEM diaphragm dosing pump has been specially developed
in order to accurately dose small quantities of liquid over a long
period of time whereby two of its most distinctive features are its
compact size and robustness (pump and electronics). The FEM
pump and electronics makes a complete dosing system which
is suitable for both simple as well as complex applications. With
the functions „quasi continuous flow“ and „batch dispensing“ the
FEM diaphragm pump differentiates itself from pumps based on
alternative technologies eg. piston, gear, syringe and peristaltic
pumps. Other interesting features are its high reliability, a
favourable purchasing price and low maintenance costs.
KNF has developed a specially programmed electronic control
module so that the integrated solenoid valve and the movements
of the diaphragm are exactly synchronised. This results in an
exact dosing which is gentle and low in pulsation. In addition
to these unique pump characteristics the control module also
allows a wide range of control possibilities to be used eg.
serial interfaces.
The dosing pump is self priming, maintenance free and can
be run dry |
|
| The broad range of SANYO DENKI fans has high reliability, low noise and affordable price. A wide range of AC and DC models allow the customer to chose the component that best fit every application. The new A series fans, optimized for cost-sensitive applications, make possible to use an high quality fan where before was impossible. LONG LIFE series fans, developed for applications whose maintenance is difficult or impossible, exceeds 100.000 hours of continuous rotation at 60°C. |
|
| ... products without technical information |
| |
The CPU-H Unit is distinguished above all by its large, central hollow shaft. The hollow shaft can be used to pass cables, shafts, welding wire, compressed air, vacuum, grease, oil or even Laser beams through the centre of the gear. In addition this Unit exhibits improved gear accuracy, higher maximum rotational speeds and a large, stiff and precise output bearing that functions simultaneously as housing. Improved corrosion protection allows use even in extreme environments.
Advantages:
- Gear Transmission accuracy improved by up to 50%
- Newly developed extremely precise, high capacity and high stiffness output bearing
- Complete corrosion protection
- Viton shaft seals for the output bearing with additional protective lip
- Output compatibility with the various CPU and CHA Series
- Zero backlash, high torsional stiffness and excellent repeatability
- High torque capacity
- Compact design and light weight
- Long operating life
- High efficiency
- Quick assembly and simple installation
- Maintenance-free with lifetime grease lubrication |
|
REDUCER CPU-M
Reducer under casing associating a reducer without play Harmonic Drive with a bearing of exit of large diameter with cross rollers.
Range CPU is a family of product, the version - M adapts to all the engines of the market. We adapt the hub to your driving shaft. The driving whole + reducing under casing CPU-M is particularly compact.
Benefit produced:
* Adaptability with all the engines of the market.
* Compactness of the assembly.
* High strength of the bearing of exit of large diameter to cross rollers
Characteristics produced:
* Couples of exit until 1840Nm,
* Radial force on the bearing of exit until 38.400N, length max 84mm.
* Utmost precision,
* Compactness of the assembly, adaptability to all the engines.
Sectors of use:
* Robotics,
* Machine tools,
* Special machines |
|
Navigator to Ultimate Comfort and Performance: Mitsubishi CNC E60 series
NEW EZMotion-NC E68
EZMotion CNC E60 Features
· Compact CNC (Panel-in structure) with integrated control unit
· High-performance CNC with 64-bit CPU
· Compact servo motors with high-resolution position encoders
· Quick selection of turning or milling modes in initial setup screen
· Analog output for the spindle’s frequency inverter drive
· All CNC data is stored in CASSETTE MEMORY hardware
E68 Features
· 8.4“ colour LCD display
· Front IC card I/F (optional)
· Compact panel-in structure
· Max. CNC axles: 4
· Max. spindles: 2
· Enhanced PLC capabilities
· Multi-language display
Customizable Screen Display
The sign-on screen is customizable. The screen display can be designed on a PC using bitmap editing software.
Advanced PLC Development Tools
PLC programming is performed with GX Developer, the development software package of the MELSEC PLC series.
|
|
|
|
