|
|
|
Agilent LCR and resistance meters are useful in testing components and materials in a variety of research and design applications and in component manufacturing. LCR meters measure impedance (inductance, capacitance, and resistance) at spot frequencies. Resistance meters are optimized for high-resistance or low-resistance measurements.
|
|
|
The B&K Precision Model 889B Synthesized In-Circuit LCR/ESR Meter with Component Tester is a high accuracy test instrument used for measuring inductors, capacitors and resistors with a basic accuracy of 0.1%. Also, with the built-in functions of DC/AC Voltage measurements and Diode/Audible Continuity checks, the Model 889B can not only help engineers and students to understand the characteristic of electronics components but also being an essential tool on any service bench.
|
|
Measuring Instrument - LCR Precision Instruments ( LCR200) :
Key Features:
- Measurement Parameters : Z , Ls , Lp , Cs , Cp ,
DCR , ESR , D , Q , and (Theta)
- Test conditions : 100MHz , 120Hz , 1KHz , 10KHz , 100KHz , 200KHz ; 1Vrms , 250mVrms , 50mVrms , 1Vdc(DCR only)
- DMM Functionalities
- Dual LCD Display with LED backlit
- Open / Short calibration
- Remote binning capability
- Auto range / range hold selection
|
|
|
|
|
|
Product ID: LCR-612
20000 Counts Hand Held LCR Meter Dual Display Auto-Ranging ( LCR-612 )
20000 Counts LCR Meter
Dual Display Auto-Ranging
MODEL: LCR-612
Outstanding Features:
1.Basic accuracy:
0.5% for Resistance
0.7% for Inductance, Capacitance
2.Dual Displays provide quick tested results readouts, with L.C.R. Display values up to 19999 counts and Q.D.R. display values up to 9999 counts
3.Excellent resolutions:
Resistance up to 0.001Ù
Inductance Capacitance up to 0.1uH/0.1pF
4.Provided up to 4 testing parameters:
Ls+(Q,D,Rs), Lp+(Q,D,Rp)
Cs+(Q,D,Rs), Cp+(Q,D,Rp)
5. Auto-Power Off function:
To conserve battery life for longer use.
6.Fuse detection function:
To inform that the fuse is open or damaged.
7.External DC Adapter functions:
Use of a DC adapter can also serve to disable Auto Power Off function.
Dual Display LCR Meter LCR-612 Test Ranges: 120Hz and 1KH
LCR-612 SPECIFICATIONS
LCR-612 Display:
LCR—4 1/2 digits, maximum reading of 19999.
QDR—4 digits, maximum reading of 9999. (Auto range).
Parameter Measurement:
Ls+(Q,D,Rs), Lp+(Q,D,Rp)
Cs+(Q,D,Rs), Cp+(Q,D,Rp)
Overload: "OL" is display.
Test Frequency: 1KHz and 120Hz.
Range Mode: Auto and Manual.
Auto Power Off:
The meter key switch inactive for more than 5 minutes, press power key to resume operation.
Measurement rate: Approx. 1 time per second, nominal.
Power Requirement: (1). Single standard 9-volt battery.
(NEDA 1604, IEC 6F22 006P) ;(2). External DC Adapter 12Vmim to 15Vmax / 50mA.(optional)
Overload Protection: 0.1A/250V fast below fuse.
Dimensions:192mm(H) x 91mm(W) x 52.5mm(D).
Weight: 365g. (including accessories)
|
|
|
The LCR Meter measure passive components with as little as 0.05 % error. These easy-to-use instruments are quick to setup, adjust and calibrate. The SR715 and SR720 are ideal for applications such as incoming inspection, quality control, automated test, and general benchtop use.
|
|
High-speed LCR meter with up to 120MHz sampling
High Speed Testing of Chip Inductors and Magnetic Heads in Research and Development
Broad Frequency Measurement Range ( 100 kHz to 120 MHz )
High speed LCR testing (6ms/sample)
14 Parameter Types ( |Z|, |Y|, Θ, Rp, Rs(ESR), G, X, B, Lp, Ls, Cp, Cs, D (tan δ) and Q )
Detachable Head Amp
Load Compensation Function
BIN ( Classification ) Measurement
|
|
1. 320x240 dot-matrix display
2. Test frequency range : 20Hz - 1 MHz
3. Measurement parameter |Z|, Rs, Rp,Xs, Rdc|, |Y|, Gp,
Bp, Ls, Lp, Cs, Cp, D, Q , Theta
4. Basic Accuracy ± 0.1%
5. Measurement Time : 30 mS ( Fast )
6. Bin Function : 8 bins (expandable to 15 bins)
7. Comparator function: Primary / Secondary
8. Memory : 256 instrument setups
9. External Memory interface (Option)
10. Interface : Handler,( Option : GPIB, RS232 ,Printer )
11. Deviation Zero : Open / Short
12. DC Bias (Option)
|
|
- LCD Display 128 x 64
- File Management ( Flash Memory Card)
- Test Point Range : 64-2048
- Test Voltage : 50-1500VDC (RT-9651 H / CH )
- Insulation Test : 500K-1000MOhm(RT- 9651H/ CH)
- 4-Wire Rsistance Test : Yes
- Components Test : Resistor,Diode,Capacitor(Option)
- Resistor Measurement : 0.1Ohm-20MOhm
- Capacitor Measurement : 100pF-1000uF
- High Quality Relay
|
|
7200 Capacitance Meter
The Model 7200 offers fast and accurate characterization of active and passive components at 1 MHz. The <50 µs risetime of the analog outputs makes this unit ideal for DLTS measurements.
• Ultra stable and repeatable measurements
• Programmable, internal 100 VDC bias
• 0.01 picofarad resolution
• High-speed, high-resolution analog outputs
• Selectable test levels
• Calibration stored in nonvolatile memory
• GPIB and HPGL
|
|
| ... products without technical information |
| |
|
|
|
|
The MICRO III, with its small dimensions of only 4,7 x 8,8 x 2,5 cm, is the ideal gas detector for personal protection. The single gas detector with ATEX certification weighs only 75 g. It detects reliably oxygen, hydrogen or many toxic gases like hydrogen sulphide, ammonia, ozone, carbon monoxide, etc. The current gas concentration is shown on a large display. With a loud alarm of 95 dB and a changing frequency the small single gas detector is audible even in noisy environments. Simultaneously, two bright and alternately flashing LEDs indicate a gas alarm. Three alarm levels and the battery alarm provide comprehensive protection.
With a permanent operation of 24 hours a day a single AA battery powers this instrument for up to 9 months. The long-life smart sensors allow the change to other gases without any problems, since the detector recognizes the new sensor type. A high-performance pump (as per ATEX) for gas sampling can be easily attached, ensuring to detect gas hazards in confined areas.
Gases to be detected: O2, H2S, CO, NO, NH3, HCN, HCl, SO2, H2, C2H4O, SiH4, PH3, COCl2, NO2, Cl2, O3, ClO2.
|
|
Hydrosteel 6000 is the ultimate portable monitoring tool for sour, HF and high temperature corrosion and diffusible hydrogen damage in steel.
The intrinsically safe instrument is totally non-intrusive and with minimal test surface preparation, and no consumables such as grease required, reliable measurements can be made within a minute.
Measurements can be taken from small pipes and large vessels, at any orientation and at any temperature up to 500 °C (932 °F), with a single probe.
|
|
DirectSense IAQ Monitors from GrayWolf make proactive indoor air quality surveys efficient and easy to conduct. Optimize the balance between facility energy efficiency and occupant health & comfort. Identify potential IAQ issues before they become problems and respond immediately to complaints with the highly accurate, extremely advanced and the most intuitive portable IAQ meters and test instrumentation available today.
This IAQ meter is designed for both walk-thru surveys and for long term (hours/days/weeks) trend logging: the 2 modes necessary for thorough Indoor Air Quality investigations.
|
|
|
The Kanomax IAQ Monitor 2211 features quick start-up and high accuracy in measuring carbon dioxide and carbon monoxide concentration levels in the environment. Temperature and humidity are also simultaneously measured in ah handy lightweight design.
|
|
The Casella CEL Microtherm Indoor Air Quality instrument is designed to monitor and record the indoor environment of storage facilities, factories, office or general workplace environments.
The overall instrument is compact and portable, allowing it to be transported and operated by a single person. Power is supplied from the mains, re-chargeable battery pack (option) or a combination of both. The fully integrated comprehensive software enables the user to archive data and generate reports automatically
|
|
Quest Indoor Air Quality Monitors provide you with a single source diagnostic tool for recording, reporting, charting, and analyzing your indoor air quality data.
Typical Applications for Indoor Air Quality Monitors include:
IAQ Complaint Investigation and Mitigation
Air Exchange Rate Measurement
HVAC System Performance Monitoring
HVAC System Balancing
Mold Investigation and Remediation
Health and Comfort Assessment
|
|
| ... products without technical information |
| |
PM100-G - Fiber Optic Power Meter
Simple optical power and loss measurement
PM100-S - Fiber Optic Power Meter
Simple optical power and loss measurement
PM200 - Fiber Optic Power Meter
Link certification and reporting tool
FO600 - FiberMeter Optical Power Meter
FO610 - High Power FiberMeter Optical Power Meter
Ideal for testing and certifying in both Multimode and Single Mode applications
|
|
Ideal for link qualification, the FiberBasix 500 series comprises the ELS-500 Light Source and the EPM-500 Power Meter. These instruments come with pass/fail thresholds (LED indicator) and a memory capacity of 1000 data items.
Applications
Link-loss characterization (ELS-500 Light Source)
LAN/WAN certification (ELS-500 Light Source)
Link-loss characterization and LAN/WAN certification (EPM-500 Power Meter)
Key Features and Benefits
Error-free testing features: automatic wavelength recognition, and no offset nulling required
Data transfer to a PC via USB connection
One-touch storage of results for all wavelengths at once (on the EPM-500)
Complete reporting software
|
|
|
The OP510 was specifically designed for applications where cost effective solutions for measuring, monitoring and logging of insertion loss or power fluctuations are needed. The OP510 is a small (4"x2"x1.25") desk friendly module designed such that minimal movement and bending of the reference- and test cables is necessary. This results in stable, accurate and repeatable measurements.
|
|
Two FasTesT ports: a three-wavelength singlemode port, including either 1625 nm or 1490 nm, and an optional two-wavelength multimode port, for a total of up to five wavelengths
Visual IL and ORL pass/fail analysis
Compatible with both the FTB-400 and FTB-200 platforms
FTTx ready: allows for the testing of passive optical networks (PONs) at 1310 nm, 1490 nm and 1550 nm, the three wavelengths recommended by the ITU-T (G.983.3) for PONs
Three-year warranty and recommended calibration interval, error-free testing and minimized training time
|
|
|
Luna Technologies' Optical Backscatter Reflectometer (OBR) delivers unprecedented inspection and diagnostic capabilities for the fiber-optics industry. Luna's state-of-the-art OBR provides isolation of faults and problems well before final test, saving hours in rework and hard dollars in yield loss.
|
|
|
Insertion Loss and Return Loss measurement for all four FTTX wavelengths. The 'no mandrel' method combined with concurrent dual-wavelength measurement makes this instrument the most efficient tool in FTTX component verification.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
