|
|
|
Agilent LCR and resistance meters are useful in testing components and materials in a variety of research and design applications and in component manufacturing. LCR meters measure impedance (inductance, capacitance, and resistance) at spot frequencies. Resistance meters are optimized for high-resistance or low-resistance measurements.
|
|
|
The B&K Precision Model 889B Synthesized In-Circuit LCR/ESR Meter with Component Tester is a high accuracy test instrument used for measuring inductors, capacitors and resistors with a basic accuracy of 0.1%. Also, with the built-in functions of DC/AC Voltage measurements and Diode/Audible Continuity checks, the Model 889B can not only help engineers and students to understand the characteristic of electronics components but also being an essential tool on any service bench.
|
|
Measuring Instrument - LCR Precision Instruments ( LCR200) :
Key Features:
- Measurement Parameters : Z , Ls , Lp , Cs , Cp ,
DCR , ESR , D , Q , and (Theta)
- Test conditions : 100MHz , 120Hz , 1KHz , 10KHz , 100KHz , 200KHz ; 1Vrms , 250mVrms , 50mVrms , 1Vdc(DCR only)
- DMM Functionalities
- Dual LCD Display with LED backlit
- Open / Short calibration
- Remote binning capability
- Auto range / range hold selection
|
|
|
|
|
|
Product ID: LCR-612
20000 Counts Hand Held LCR Meter Dual Display Auto-Ranging ( LCR-612 )
20000 Counts LCR Meter
Dual Display Auto-Ranging
MODEL: LCR-612
Outstanding Features:
1.Basic accuracy:
0.5% for Resistance
0.7% for Inductance, Capacitance
2.Dual Displays provide quick tested results readouts, with L.C.R. Display values up to 19999 counts and Q.D.R. display values up to 9999 counts
3.Excellent resolutions:
Resistance up to 0.001Ù
Inductance Capacitance up to 0.1uH/0.1pF
4.Provided up to 4 testing parameters:
Ls+(Q,D,Rs), Lp+(Q,D,Rp)
Cs+(Q,D,Rs), Cp+(Q,D,Rp)
5. Auto-Power Off function:
To conserve battery life for longer use.
6.Fuse detection function:
To inform that the fuse is open or damaged.
7.External DC Adapter functions:
Use of a DC adapter can also serve to disable Auto Power Off function.
Dual Display LCR Meter LCR-612 Test Ranges: 120Hz and 1KH
LCR-612 SPECIFICATIONS
LCR-612 Display:
LCR—4 1/2 digits, maximum reading of 19999.
QDR—4 digits, maximum reading of 9999. (Auto range).
Parameter Measurement:
Ls+(Q,D,Rs), Lp+(Q,D,Rp)
Cs+(Q,D,Rs), Cp+(Q,D,Rp)
Overload: "OL" is display.
Test Frequency: 1KHz and 120Hz.
Range Mode: Auto and Manual.
Auto Power Off:
The meter key switch inactive for more than 5 minutes, press power key to resume operation.
Measurement rate: Approx. 1 time per second, nominal.
Power Requirement: (1). Single standard 9-volt battery.
(NEDA 1604, IEC 6F22 006P) ;(2). External DC Adapter 12Vmim to 15Vmax / 50mA.(optional)
Overload Protection: 0.1A/250V fast below fuse.
Dimensions:192mm(H) x 91mm(W) x 52.5mm(D).
Weight: 365g. (including accessories)
|
|
|
The LCR Meter measure passive components with as little as 0.05 % error. These easy-to-use instruments are quick to setup, adjust and calibrate. The SR715 and SR720 are ideal for applications such as incoming inspection, quality control, automated test, and general benchtop use.
|
|
High-speed LCR meter with up to 120MHz sampling
High Speed Testing of Chip Inductors and Magnetic Heads in Research and Development
Broad Frequency Measurement Range ( 100 kHz to 120 MHz )
High speed LCR testing (6ms/sample)
14 Parameter Types ( |Z|, |Y|, Θ, Rp, Rs(ESR), G, X, B, Lp, Ls, Cp, Cs, D (tan δ) and Q )
Detachable Head Amp
Load Compensation Function
BIN ( Classification ) Measurement
|
|
1. 320x240 dot-matrix display
2. Test frequency range : 20Hz - 1 MHz
3. Measurement parameter |Z|, Rs, Rp,Xs, Rdc|, |Y|, Gp,
Bp, Ls, Lp, Cs, Cp, D, Q , Theta
4. Basic Accuracy ± 0.1%
5. Measurement Time : 30 mS ( Fast )
6. Bin Function : 8 bins (expandable to 15 bins)
7. Comparator function: Primary / Secondary
8. Memory : 256 instrument setups
9. External Memory interface (Option)
10. Interface : Handler,( Option : GPIB, RS232 ,Printer )
11. Deviation Zero : Open / Short
12. DC Bias (Option)
|
|
- LCD Display 128 x 64
- File Management ( Flash Memory Card)
- Test Point Range : 64-2048
- Test Voltage : 50-1500VDC (RT-9651 H / CH )
- Insulation Test : 500K-1000MOhm(RT- 9651H/ CH)
- 4-Wire Rsistance Test : Yes
- Components Test : Resistor,Diode,Capacitor(Option)
- Resistor Measurement : 0.1Ohm-20MOhm
- Capacitor Measurement : 100pF-1000uF
- High Quality Relay
|
|
| ... products without technical information |
| |
|
High quality analogue instruments designed to measure an extensive range of electrical and electronic parameters. This comprehensive range offers DIN instruments, ANSI switchboard meters, panel indicators, sealed and ruggedised instruments, and complementary selector switches for line to line and line to neutral readings. Instruments are precision engineered and robust in design, ensuring accurate measurement and display in the most demanding of environments. All instruments are available in a range of styles, sizes and specifications to meet the exacting needs of industry.
|
|
The 236, 237, and 238 Source-Measure Units (SMU) are fully programmable instruments, capable of sourcing and measuring voltage or current simultaneously. These systems are really four instruments in one: voltage source, current source, voltage measure, and current measure.
Related Applications:
- MOSFET measurements
- GaAs measurements
- Bipolar measurements
- Diode characterization
- Oxide characteristics
- Electromigration testing
- Research and electronic manufacturing applications
|
|
E Probe now under development process
* Non contacting E field Measuring,
* Directional sensitivity
* Power supplies +/-12V
* Measuring range 1 milliVm-1 up to over 1000Vm-1
* Bandwidth : 10 mHz - 100 kHz
* White noise: μVm-1/√Hz experimentally shown
|
|
Portable PD Analyzing System LDS-6/UHF
for PD measurements and monitoring on GIS or Cable Systems
The LDS-6/UHF is a state-of- the-art, portable digital measuring system for the UHF processing of partial discharges acquired from installed GIS sensors, or UHF sensors. It combines the features of a PD detector and spectrum analyzer.
PD quality tests on GIS using installed GIS sensors
PD testing on HV Apparatus, using UHF technology
Designed for on-site PD diagnosis tests as well as for manufacturing and research
Single channel or Dual channel
Available in 19" housing with external PC connected via Ethernet, or portable case with built in mini PC
|
|
Digital Partial Discharge Measuring and Diagnostics System for industrial and general HV test floor environments.
The LDS-6 is a highly sophisticated digital measuring system for the PD detection according to the standard IEC 60270, VDE 0434 as well as various IEEE and other standards for the High Voltage Test and Measurement Technology. It meets also ICEA T-24-380 standard for Cable Industry.
PD quality tests on high voltage equipment
PD diagnosis on developing insulating materials
Designed for on-site PD diagnosis tests as well as for manufacturing and research
PD fault location for power cables
|
|
| ... products without technical information |
| |
The wish of operators and technologists in the wood-based panel industry to scan the raw density profile online during the running production has been regarded as impractical for many years.
By means of the GreCon Inline Raw Density Profile Measuring System StenOgraph, it is possible for the first time to scan the raw density profile, as one of the most important criteria of the quality of particle board and fibreboard, online after continuous presses.
This enables the operator to influence the raw density profile and thus the features of MDF and particle board during the production process.
Shorter running-in times of new production plants and during product changes as well as an optimised production process lead to substantial savings in cost and material while the panel quality is improved.
|
|
|
|
|
|
Portable Density Meter: DMA 35
The DMA 35 portable density meter measures the density and concentration of your sample and is characterized by the highest level of user friendliness. Its robust and lightweight design enables the use in numerous fields of application and its on-site operation in a wide range of work environments. This basic model enables the manual selection of measuring methods and sample IDs as well as wireless data exchange with a printer or PC. Therefore DMA 35 is an economic solution for general industrial and laboratory applications with constant or only occasionally changing measurement settings.
User friendliness
* Compact, lightweight design enabling one-hand measurement
* Easy operation, even when wearing protective gloves
* No-hassle measurement of hard-to-reach samples
* Large LC display with backlight for clear visibility of measuring results
* Measuring cell with inspection window and backlight
Robustness
* Rugged, leakproof housing design
* Designed for industrial and field applications
* Proven resistance of wetted parts against common samples
Wireless communication
* IrDA interface for data exchange with a PC and data export to a printer
Efficiency
* Storage of up to 100 sample IDs for easy sample identification
* Storage of up to 20 measuring methods
* Storage of up to 1024 measurement results including time stamp and sample ID
* Up to five programmable custom functions
* Two exchangeable 1.5 V AA batteries ensure long-term, reliable service
* Energy-saving mode for reduced power consumption provided
* Easy and fast replacement of the entire pump assembly
|
|
Concentration, Water Content and Dry Substance measured by microwaves
Your Advantages:
High selective sensitivity to water
High accuracy and long-term stability
even for difficult products
Simple installation, insertion directly
on the existing pipelines, vessels, chutes etc.
Simple start-up, system supported sample taking,
automatic calibration and graphic display
Accurate and reliable measurement
due to two highly stable PLL-synthesizers
and multi-frequency technology
Durable sensor measuring cells with wear resistant
smooth walled PTFE lining
Contactless measuring cell without installed
measuring antenna
High operational safety and standards of quality
|
|
|
|
|
|
|
The compact, rugged Thermo Scientific SGD-O is the most reliable non-contacting density gauge for monitoring fluid density, including PPG, PPA and SGU, in the oilfield during fracturing and cementing. Capable of enduring high shock and vibration yet lightweight, this advanced device features rapid response and high accuracy to improve consistency, safety and overall performance. Engineered to withstand the extreme moisture and high humidity of oilfield environments, it rapidly indicates variations in slurry density and proppant concentration during fracturing and cementing operations. The SGD-O is comprised of three components: the source and detector work together to measure the fluid density while the remotely located electronic transmitter provides a clear digital display of the measurement. This advanced gauge measures through any pipe thickness, with the detector providing response in three to five seconds and accuracy of ±0.1 pounds per gallon. The transmitter can be mounted up to 100 feet away from the gauge to ensure worker safety. It can be powered by a readily available 12 or 24 volt power supply and features quick disconnect connectors for cable and transmitters. The SGD-O is also easy-to-install and use and has minimal maintenance requirements.
|
|
|
|
|
|
PROCESS LOW FLOW RATE LIQUID IN-LINE DENSITY METERS DC-30 SERIES
LEMIS process uses the proven vibrating element technology which is widely accepted as the most accurate of continuous density measurement. It is based on the frequency changing of the sensitive unit and resistance of the built-in temperature sensor in dependence of characteristics of measured liquid. The oscillation period of the sensitive unit mainly depends on density and temperature of measured liquid.
Continuous monitoring optimizes, controls and manages the processes. DC-30 series has a variety of applications, where low flow rate does not allow to install standard high flow systems. PC connection allows distance control for the most critical parameters in such processes as organic synthesis and chemical reactions in reactors.
New age of LEMIS process combined meters measure various critical parameters: density, concentration, dynamic viscosity, kinematic viscosity, temperature. Two meters in one device saving cost of installation and maintenance!
|
|
|
|
|
|
PORTABLE LIQUID IN-TANK DENSITY METERS DM-250 SERIES
Portable Submersible Density meter DM-250.1 and DM-250.2 are best suited for liquid density and temperature measurements directly in the storage or process tanks (up to 30 meters depth). No labor extensive and errors critical sampling required. Instead, the sensor of DM-250.1 and DM-250.2 are submersed at any required level and record spot density and real temperature at that point directly in the liquid. The operation personal can get in minutes the average density in the tank and its density / temperature / level profile, for example, at every meter. DM-250.3 is best for situation when DM-250.1 and DM-250.2 could not be installed. Just take a sample that is over a hundred mililitres of sample and the equipment will give you the results in seconds! Hundreds of measurements can be stored locally and future transferred to a PC or printer via built-in Bluetooth connectivity.
Density determination directly in the tanks is faster, easier, more precise and cost effective comparing with conventional technique requiring sampling and use of glass hydrometers by qualified personal. That is why the DM-250 series portable density meters from LEMIS process have found wide application, first of all in oil industry upstream and downstream operations where control of quality (density) and quantity (mass) of petroleum products at movement and storage is very critical.
New age of LEMIS process combined meters measure various critical parameters: density, concentration, dynamic viscosity, kinematic viscosity, temperature. Two meters in one device saving cost of installation and maintenance!
|
|
|
|
|
|
Super high-speed sampling at 2000 times/second. Digital hold and peak hold functions. Ideal for measuring the dynamic phenomena of loads, pressure, torque, tension, etc.
The AD-4532B is equipped with a 2D (5-level) comparator function. This function makes it possible to determine the acceptability of the total result by performing a sequential comparison while shifting between the upper/lower limit in five levels using a time axis or an external input (trigger). The AD-4532B is ideal for use in measurements such as a press-in operation, which require changes in the comparison value as time elapses. The five comparators can also be used separately. The comparator judgment is indicated by a highly intuitive, tricolor (Orange/Green/Red) LED on the measurement data display.
The AD-4532B also features a chatter-prevention function. If bouncing of the comparator value occurs repeatedly near the upper/lower limit, a heavy burden will be placed on the relay circuit and other parts. To prevent this, the AD-4532B has a function to set the hysteresis width and time.
The AD-4532B comes equipped with an analog amplifier voltage output (±10V), a D/A analog voltage output (±10V), a comparator output and a Modbus-RTU input/output. In addition, we offer an optional BCD output, RS-232C input/output, D/A analog voltage/current output (±10V / 4-20mA) and Ethernet. The upper/lower limit setting, the zero compensation function and the hold function can be executed via Modbus-RTU.
Please see the AD-4532B catalog for further details.
|
|
The LCIC-WIM is the 2nd generation to our popular line of Load Cell Interface Card that thousands of them are being used all around the world. The LCIC-WIM samples the Load Cell in a rate of 52,000 samples per second so, it fits all dynamic weighing and force measurement applications.
The package includes also our unique LCIC-WIM Monitor utility which is a vital tool for analyzing dynamic load/force applications. It allows to collect the data, showing the results in graphic mode or save it for later use in excel etc.
The communication with the LCIC-WIM is via USB or RS232/485 so, it can be used with almost any PC or other computer.
|
|
A truly measured roll force is crucial in achieving correct roll gap settings, true force distribution from operator side to drive side of your mill and supervision of the backup bearings and roll eccentricity. The Millmate Roll Force System incorporates all these essential features.
The Millmate Roll Force System consists of a Millmate Controller (MC 400) and two load cells with matching units. The various types and the wide load range of Millmate Roll Force load cells cover practically all conceivable roll force measurement applications.
|
|
The DFS-II is a system used for testing the force on the tip of the tool of a wire bonder and in some die attach bond heads as well. The DFS-II system scope displays a wave form that permits the user to establish whether there is excessive vibration, impact force or unwanted movement on the bond head as it touches down on the surface of the DFS-II Sensor. The wave form can then be printed on the on board printer for hard copy recording.
This is a perfect tool for calibration, troubleshooting, setup and verification of machine operation. Both force and time duration can be measured in actual units (force in grams and time in milliseconds) without the need of conversion charts or extra calculations. The DFS-II can be used with wire bonders of any type (automatic, semiautomatic and manual) and of any manufacture. Maximum force measured by the sensor is 500g.
Contact us at mailus@hybond.com for more information.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
