|
|
|
IMP57 is a fundamental accessory for verifier and engineer to perform, connected with GSC5x, SIRIUS 89, Macrotest 5035, Genius 5080E or Combitest 2019, the Loop/Line impedance and the prospective short circuit current evaluation on a distribution circuit. The high value of test current generated (max 200A) allows quick and accurate measurement (0,1mOhm resolution) also close to power transformer. IMP57 consists in a practical and strong plastic suitcase, it haven't any display and can be connected by RS-232 to the above meters (called Master) to read the measurement results. With 4-wire measurement method the results aren't affected by test leads and it's no necessary perform any preliminary calibration.
|
|
MIT410TC and MIT430
Insulation Resistance and Continuity Testers
• Insulation testing up to 1000 V and 200 G?
• Patented analog arc and dual digital display
• CAT IV 600 V rating
• TRMS & DC Voltage measurement
• Continuity testing at 200 mA or 20 mA down to 0.01
• Pass/Fail limit alarms
• PI/DAR and Timer function
• Test result storage (MIT430)
• Bluetooth® wireless data transfer (MIT430)
• Three year product warranty
• IP54 rated
|
|
FEATURES:
1. DIM 571 is a LCD Indicated instruments for insulation (M Ohm), Continuity (OHM) and AC Voltage
2. Three Insulation test voltage (DCV): 250V, 500V, 1,000V.
3. Large LCD display(68 x 34mm)
4. Test Insulation at rated voltate into 1 1mA load
5. 200mA short circuit continuity current.
6. Timer for test functions (3 ~ 5 minutes)
7. Data Hold function
8. Auto power off function
9. Automatic circuit dischage
10. Fuse proection
11. EN61010 CAT III 600V
12. BS 16" Edition
|
|
The IRT 1557 is a small, lightweight insulation resistance and continuity tester. Hand-held, it's a superb addition to any test engineer's toolkit.
It performs measurements according to BS 7671 16th/17th Edition Wiring Regulations and Part P. Seaward's unique integrated safety probe puts the LCD and test probe in the user's line of sight whilst making measurements, no other tester does this. IRT 1557 is fully compliant with EN 61557 and IEC 61010-1 600v CAT lll. Automatic discharge of capactive circuits, it gives you automatic warning of the presence of hazardous voltages.
It comes with an easy to use rotary setting switch. The IRT 1557 offers a number of unique features, including voltage measurements up to 1000AC or DC and a dual safety rating. With incredible robustness the IRT 1557 provides all the tests you need with a safe feel.
|
|
1000V Megohmmeters
AEMC® manufactures a complete line of insulation testers designed to test the quality of insulation using 1000V test voltage required for testing equipment designed to be powered by 480VAC. Both analog and digital meters are available. AC powered, battery powered and hand crank models are available. Most models will measure into the GΩ and TΩ range. Most models offer multi-function capability, measuring AC/DC volts, resistance and continuity as well as insulation resistance. Both hand held instruments and rugged instruments built into portable cases are available.
|
|
1039 100V Megohmmeters
The Megohmmeter Model 1039 is a battery powered digital insulation resistance tester. It is designed to measure insulation resistance, current, capacitance, cable length, voltage and to measure resistance. The Model 1039 tests are 50 and 100V. It incorporates a 600V voltmeter which automatically detects and accurately displays AC/DC voltages in the test circuit on each of the insulation test voltage ranges. Above 25V it also provides and audible and visual signal, and inhibits further tests, thus protecting the user and the meter.
An exceptionally large digital/analog multi-function display provides clear and easy readings enhanced by a bright blue electroluminscent backlight.
|
|
5000V Megohmmeters
AEMC® manufactures a complete line of insulation testers designed to test the quality of insulation using 5000V test voltages required for testing large motors, generators, transformers and cables. Both analog and digital meters are available. AC powered and battery powered models are available. Most models will measure into the GΩ and TΩ ranges. All models offer multi-function capability, measuring AC/DC volts, resistance and continuity as well as insulation resistance. Both hand held instruments and rugged instruments built into portable cases are available.
|
|
1040 1000V Megohmmeters
The Megohmmeter Model 1040 is a battery powered digital insulation resistance tester. It is designed to measure insulation resistance, continuity, voltage and to measure resistance. The Model 1040 tests are 500 and 1000V. It incorporates a 600V voltmeter which automatically detects and accurately displays AC/DC voltages in the test circuit on each of the insulation test voltage ranges. Above 25V it also provides an audible and visual signal, and inhibits further tests, thus protecting the user and the meter.
An exceptionally large digital/analog multi-function display provides clear and easy readings enhanced by a bright blue electroluminscent backlight.
|
|
METRISO 5000A: analog high-voltage insulation measuring instrument with 4 measuring voltages: 100, 250, 500
and 1000 V (per EN 61 557 part 2) and 1500, 2000, 2500 and 5000 V
METRISO 5000AK: The battery powered METRISO 5000 A is converted into the muscle powered
METRISO 5000AK by replacing the battery module with a crank generator.
- Extensive measuring range: 10 kOhm... 1 TOhm
- Measuring range: 100 kOhm... 100 MOhm (1000 V)
- Measuring voltages: 100 V, 250 V, 500 V, 1000 V, 1500 V, 2000 V, 2500 V, 5000 V
- Measurements to 1000 V per DIN VDE 0413
- Voltage measurement to 2000 V ,
- Concise logarithmic display
- Guard terminal for the elimination of surface current
|
|
The DRM-100 instrument can precisely measure contact resistance on circuit breakers, switches, bus bar joints and other lowresistance devices in a high voltage environment.
Digital Resistance Meter Instrument Features
* Precise contact resistance measurement
* True DC current is automatically ramped up and down
* Test cycle programmable from 10-60 seconds
* Large, bright, high resolution, color screen
* Continuous mode for trouble shooting
* High accuracy and resolution
* Emergency OFF button and auxiliary grounding terminal for safety
* High strength and waterproof Instrument case for rough field use
* Test leads and accessories in separate carrying case
* Also available with internal memory, printer, USB port. Model DRR-100
* Color screen
* Auto ranging
|
|
Teraohm, is an ultra high range insulation resistance testing instrument with an output voltage of up to 10000 volts dc. It will measure up to 10 TeraOhms (10,000,000 MegaOhms). This insulation tester is suited for transformer, generator and large motor insulation resistance testing.
Features
* Insulation resistance measurement up to 10 TeraOhm (10,000,000 MegaOhm)
* Output voltage up to 10 kV in steps of 25 V
* Diagnostic tools (PI, DAR, DD)
* Fast charging of capacitive loads using 5 mA current source
* Automatic discharge of capacitive charge
* Large display with digital and bar-graph results
* Optional TeraLink Pro PC software for MS Windows®
|
|
|
|
|
|
Digital Winding Resistance Reporter
Model DWR-10
The Digital Winding Resistance (DWR) REPORTER can measure and save more than 10,000 high-resolution test results along with transformer nameplate data. With its expansive memory, its bright 45/8" x 3½" LCD screen and the attractive reports from its 40-character wide built-in printer, the DWR is the new standard in test equipment for the Transmission and Distribution Industry. The DWR can store hundreds of files. Each file can contain a virtually unlimited number of winding resistance measurements with tap and winding details of each, and several fields of information about the transformer, its location and the operator's name.
DWR REPORTER Features
- A large, color LCD screen for entering equipment details and presenting results, in various languages
- An expansive memory capacity for test results
- A robust power supply for fast testing of large power transformers
- An 40-character-wide built-in printer
- Remote tap-changer operation
- Compatible with Microsoft Excel® and Microsoft Word®
The Digital Winding Resistance Reporter file manager makes it easy to locate, open, view and print past results. Files are conveniently named according to the transformer serial number (up to 99 duplicates are permitted using an automatic suffix). Files are easily transferred to PC (RS-232 and USB ports).
|
|
|
The ground resistance of substations can be measured with two auxiliary electrodes which are put into the ground. To avoid influences from the mains current and its harmonics, this measurement should preferably be carried out with 128 Hz.The high output power of the CPC 100 ensures a high ratio of the signal level to the noise level. Thanks to the signal processor technology, the measuring procedure is very selective and disturbances by ground currents are reduced to a minimum.
|
|
Multi-purpose coupling unit for CPC 100
CP CU1 is a coupling-unit designated for measurements with the CPC 100 test system on overhead lines and power cables. Typical applications of this world-wide unique system include: Line impedances and k-factors of overhead lines or power cables, Mutual coupling of parallel lines, Coupling of power lines into signal cables,
Ground impedances of large substations, Step and touch voltages.
The test system offered by OMICRON makes use of frequency shift techniques for accurate measurements regardless of electrical interference.
Applications
- Line impedance and residual compensation factor (k-factor) measurements
- Positive and zero sequence impedance measurements of power lines
- Measurement of mutual coupling of parallel lines
- Measurement of ground impedances of large substations
- Step and touch voltage measurements
- Measurement of coupling impedances between power lines and signal cables
|
|
Earth Testing covers the testing of earth electrodes and the measurement of soil resistivity. The instrument requirements depend on the range of applications.
|
|
AutoPoint DT is a fixtureless, gridless flying probe with a unique power-off impedance analysis measurement system. Excellent for Manufacturing Defect Analysis (MDA) testing and Field Return Failures.
Supplied as a Stand Alone System or integrated with the PinPoint II Advanced Diagnostic Test System System
|
|
3731 Clamp-On Ground Resistance Testers
The Clamp-on Ground Resistance Tester Model 3731 measures ground rod and small grid resistance through any season, without the use of auxiliary ground rods.
Check Resistance on Single and Multiple Rods or Grids
Clamp-on Ground Resistance Testers are used in multi-grounded systems without disconnecting the ground under test. The Model 3731 simply clamps around the ground conductor or rod and measures the resistance to ground. By performing measurements on intact ground systems, the user also verifies the quality of the grounding connections and bonds. Resistance and continuity of grounding loops around pads and buildings may also be measured.
The Model 3731 also provides alarm and memory functions.
|
|
Ground resistance meter 3-electrode measurement on the 3151 gives greater precision !
Ground resistance measurement involves factors that are not encountered during ordinary resistance measurement, such as polarization of the earth, the influence of grounding current due to leak current and grounding voltage, and the influence of auxiliary grounding resistance. The 3151 is able to make more accurate measurements more safely under difficult conditions because it uses the alternating current potentiometer method to provide measurement accuracy, and because it contains features such as an auxiliary grounding resistance check feature and measurement frequency switching.
|
|
DEHNcap Test Adapter/Measuring Impedance
* Easy mechanical and electrical adaptation to HR, LR or XC test sockets
* Measuring impedance for maintenance tests of coupling units with suitable µA meter
* 4 mm safety plugs or sockets
* Energised HR plug, insulated
|
|
PART # SBS BCT-5000
DC RESISTIVE LOAD BANK (24, 48, & 120 VDC)
The only way to know your industrial batteries will perform to specification is to test them regularly. SBS's battery capacity testers enable you to test your wet or sealed batteries in a variety of ways and at three voltages. Load bank test 24V, 48V, or 120V DC systems with currents up to 171 amps. A built-in digital meter lets you read volts, amps, amp-hours, and elapsed time without having to hook up a separate meter. The display is accurate to 1% of full scale at the rated voltages. The unit also offers continuous operation, so there's no cool down needed after or between tests. Use the master load control switch to instantly apply or remove loads.
|
|
Testing of insulation plays a great role in electrotechnics.Dielectric breakdown tests are important to the safe functioning of everything from power distribution transformers to household appliances. Impulse voltage tests are characterized by a 1.2/50us waveform. This is as industry standard.
The huge range of devices to be tested requires impulse generators from a few hundred volts(V) up to hundreds of thousands of volts(kV). The impulses have low energy content, but this can vary depending on the application.
EMC PARTNER offer a range of instruments starting from 250V up to 100kV. All units have the necessary connections and safety features relative to the test.
Many product specific standards incorporate insulation testing as part of the safety criteria.
|
|
|
|
|
|
FULLTEST4058 model was designed from HT ITALIA to performing essential tests in industrial environments on electrical machines devices and partially type-tested assemblies (PTTA) in compliance with EN60204-1 and EN60439-1 respectively.
The meter principally performing Continuity test on potential equalising conductors with >10AAC test current, Insulation Resistance with 500VDC test voltage and Withstanding tests with 1000AC test voltage (for electrical machine devices) and 2500V test voltage (for individual test on PTTA assemblies switchboards).
Withstanding test is performed also in BURN mode with no limits on trip-out current. Discharging Time measures of internal capacitance and on external plugs of device under test complete the list of possible test with this meter.As FULLTEST4050 more advanced model also FULLTEST4058 have a built-in internal memory to save all measurement results and a RS-232 PCs interface for directly transfer of saved tests by dedicated Windows software.
The model is fitted inside a practical and protected plastic case board with no flammability and a membrane keyboard for rapid selection of functions is included on the frontal panel together a wide custom display.
FULLTEST4058 is the ideal solution for any kind of verifier and/or industrial installer to performing easily and rapid test on industrial appliances.
|
|
The S1-552 is an advanced 5kV insulation tester with a high output current and many time-saving features. A large, analog/digital LCD shows resistance valves up to 5 T%u03A9 and incorporated a timer and other test information. The output current, of up to 5mA, speeds up testing by charging capacitive loads quickly.
The 5 and 15-kV Megohmmeters are high-voltage, line operated instruments that can be used on all types of insulation tests ranging from 500 volts to 15 kV.
With over twenty 1-kV models to choose from, selecting the proper Megger insulation tester can appear a bewildering task at first. Actually all the process requires is a little organization. All Megger insulation testers perform essentially the same test in fundamentally the same manner %u2014 accurately and reliably. Refinements and added features, however, separate one model from another in application and operator appeal.
|
|
|
The partial discharge measurement of electric motors and generators during the current enterprise is world-wide increasingly used. Thus isolation problems can in time be recognized and revision work be better planned.
|
|
- Waveform (Range):Oscillation (up to 4 µF, Vmax 6000 V; 4 µF up to 10 µF, Vmax 4000 V)
- Coupling:up to 800 V rms/16 A for <= 6 s / up to 380 V rms/16 A for continuous operation
- Standards:IEC 60348-14 Amd.1,
- Options:EN 132400
- Required Accessory:Coupling Switch Matrix TC-MIG24, TEMA
|
|
Featuring Four Instruments in One
AC Hipot to 7KV
DC Hipot to 10KV
Earth Continuity Testing 1mOhms
Insulation Resistance 65GOhms to 2500V
Arc Detection with usec shutdown
Programmable
IEEE-488.2, RS232 Interfaces
|
|
MEGATEST-1
Digital Insulation Tester
Large LCD display with 60 segment bar graph
Test voltage 250, 500 V, 1000 V DC
Insulation measurement to 4000 M&Mac189;
Voltage to 600 V AC/DC
Acoustic continuity test
Memory for 4,000 test values
with RS-232 interface
CAT III 600 V
|
|
|
AEMC® manufactures a complete line of insulation testers designed to test the quality of insulation using 1000V test voltage required for testing equipment designed to be powered by 480VAC. Both analog and digital meters are available. AC powered, battery powered and hand crank models are available. Most models will measure into the GΩ and TΩ range. Most models offer multi-function capability, measuring AC/DC volts, resistance and continuity as well as insulation resistance. Both hand held instruments and rugged instruments built into portable cases are available.
|
|
|
|
|
|
C.A 6549
In its site-adapted casing, the C.A 6549 insulation tester offers quantitative and qualitative insulation analysis, on a large backlit graphic screen!
· measurement range: 10kΩ to 10TΩ!
· 4 fixed test voltages: 500 / 1,000 / 2,500 and 5,000V
· adjustable test voltage position: 40 to 5,100V in 10V or 100V increments
· step voltage mode: R(Utest) measurement curve viewed on the screen and gradient calculated automatically in ppm/V
· DAR, PI and DD quality ratios calculated automatically
· programmable test length and R(t) measurement curve displayed directly on the screen
· with indication of measurement t° after measurement, resistance recalculated to reference temperature for reliable and accurate insulation monitoring
· many other functions: test voltage locking, smooth function, programmable alarms, etc.
· can record thousands of measurements
· RS 232 connector for connection to PC or very compact serial printer
· power supply: rechargeable NiMH battery for 30 days' operating with 10 DAR measurements and 5 PI measurements per day
· electrical safety: IEC 61010-1 Cat.III 1,000V or Cat.I 2,500V and 61557
· dimensions: 270x250x180mm; mass: 4.3kg
|
|
Maximum 5kV Test Voltage - Up to 5TΩ of Insulated Resistance Testing
Safely evaluate the insulation characteristics of high voltage transformers, motors and cables
Measure insulation of high-voltage equipment (such as transformers, cables, and motors)
Automatically calculate and display the PI (Polarization Index) and DAR (Dielectric Absorption Ratio)
Temperature compensation to accurately respond to variations in insulation material
Data storage and USB interface
|
|
|
|
